Kwon-Hee Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kwon-Hee Kim has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
Chang-Hee Cho
Department of Precision Machinery, Gyeonggi College of Science and Technology, Siheung, Republic of Korea
6 shared publications- Doo-Hyun Cho
Department of Mechanical Engineering, Graduate school, Korea University, Seoul, Republic of Korea
3 shared publications Hyo-Chan Kwon
Agency for Defense Development
3 shared publicationsKwang Joon Kim
Korea Univ, Dept Mech Engn, Grad Sch, Seoul, South Korea
3 shared publications- Kwang Joon Kim
Department of Robotics and Mechatronics, Korea Institute of Machinery and Materials (KIMM), Daejeon, South Korea
3 shared publications Soo-Won Chae
Department of Mechanical Engineering, Korea University, Seongbuk-gu, Seoul, Republic of Korea
3 shared publications
Latest Publications
- Open Access
- 16 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2048
Characterization of Deburring by Abrasive Flow Machining for AL6061
Burrs form due to the plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through milling burr edge erosion tests by abrasive flow. Based on the assumption that the flow component is tangential to the burr edge has relatively little contribution to the edge erosion, an attempt was made for the application of the new objective function to the three-dimensional burr edge formed by two intersecting holes drilled with offset. The deburring test results and predictions from three-dimensional computational fluid dynamics’ (CFD) simulations were in reasonable agreement.
- 16 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2048
Open AccessCharacterization of Deburring by Abrasive Flow Machining for AL6061
Burrs form due to the plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through milling burr edge erosion tests by abrasive flow. Based on the assumption that the flow component is tangential to the burr edge has relatively little contribution to the edge erosion, an attempt was made for the application of the new objective function to the three-dimensional burr edge formed by two intersecting holes drilled with offset. The deburring test results and predictions from three-dimensional computational fluid dynamics’ (CFD) simulations were in reasonable agreement.
- Open Access
- 27 January 2022
- Published by MDPI AG in Preprints.org
Characterization Of Deburring By Abrasive Flow Machining for AL6061
Burrs form due to plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through experiments. Based on this new objective function, a prediction of deburring performance on the burr edge of the intersecting holes with offset was performed. The results between the predicted and experimental observation results were in reasonable agreement.
- 27 January 2022
- Published by MDPI AG in Preprints.org
Open AccessCharacterization Of Deburring By Abrasive Flow Machining for AL6061
Burrs form due to plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through experiments. Based on this new objective function, a prediction of deburring performance on the burr edge of the intersecting holes with offset was performed. The results between the predicted and experimental observation results were in reasonable agreement.
- Open Access
- 10 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (2) , 657
Improvement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in linear stage type test equipment. For this purpose, the causes of the position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, adding balancing weights to the platform unit and adjusting the stiffness of the LM Guides are proposed. These methods reduce the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- 10 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (2) , 657
Open AccessImprovement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in linear stage type test equipment. For this purpose, the causes of the position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, adding balancing weights to the platform unit and adjusting the stiffness of the LM Guides are proposed. These methods reduce the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- Open Access
- 23 November 2021
- Published by MDPI AG in Preprints.org
Improvement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- 23 November 2021
- Published by MDPI AG in Preprints.org
Open AccessImprovement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- 26 March 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (6) , 1061-1067
Strain Hardening Characteristics of 99.9% Pure Silver at Large Strains
- 26 March 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (6) , 1061-1067
Strain Hardening Characteristics of 99.9% Pure Silver at Large Strains
- 12 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 791-798
Underactuated Three-Finger Robot Hand with Human-Like Flexion
- 12 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 791-798
Underactuated Three-Finger Robot Hand with Human-Like Flexion
- 8 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (3) , 441-451
Efficient Removal of Milling Burrs by Abrasive Flow
- 8 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (3) , 441-451
Efficient Removal of Milling Burrs by Abrasive Flow
- 1 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (4) , 567-577
Energy Absorption of Square Tubes with Perforations in Dynamic Axial Crush
- 1 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (4) , 567-577
Energy Absorption of Square Tubes with Perforations in Dynamic Axial Crush
- 19 November 2019
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 21 (1) , 75-80
Study on the Design of a New Heatsink Cooling System for Thermoelectric Dehumidifier
- 19 November 2019
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 21 (1) , 75-80
Study on the Design of a New Heatsink Cooling System for Thermoelectric Dehumidifier
- 31 July 2019
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 43 (7) , 507-511
Deburring of Offset Hole Intersection with Abrasive Flow Machining
버는 드릴링, 절삭 등의 기계가공 과정에서 소재의 소성변형에 의해 발생하는 의도치 않은 잔여물이다. 특히, 빗겨서 생성된 교차구멍에서의 버는 가공품의 내부 깊은 곳에 생성되어 접근이 매우 어렵고, 형태가 복잡하여 버의 제거가 쉽지 않다. 본 연구는 빗겨서 직교하는 교차구멍을 입자유동 방식으로 디버링하는 경우, 여러 가공 변수들의 영향을 알아보았다. 실험은 Al6061 소재에 대하여 L8 직교배열표를 이용하여 유동거리, 연마재 입자크기, 연마액 농도, 연마액 점도, 그리고 유속을 변수로 선정하여 진행하였다. 민감도 분석을 통하여 디버링의 완성도는 유동거리에 따라 크게 의존하며 유속의 영향은 상대적으로 작다는 것을 알 수 있었다.
- 31 July 2019
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 43 (7) , 507-511
Deburring of Offset Hole Intersection with Abrasive Flow Machining
버는 드릴링, 절삭 등의 기계가공 과정에서 소재의 소성변형에 의해 발생하는 의도치 않은 잔여물이다. 특히, 빗겨서 생성된 교차구멍에서의 버는 가공품의 내부 깊은 곳에 생성되어 접근이 매우 어렵고, 형태가 복잡하여 버의 제거가 쉽지 않다. 본 연구는 빗겨서 직교하는 교차구멍을 입자유동 방식으로 디버링하는 경우, 여러 가공 변수들의 영향을 알아보았다. 실험은 Al6061 소재에 대하여 L8 직교배열표를 이용하여 유동거리, 연마재 입자크기, 연마액 농도, 연마액 점도, 그리고 유속을 변수로 선정하여 진행하였다. 민감도 분석을 통하여 디버링의 완성도는 유동거리에 따라 크게 의존하며 유속의 영향은 상대적으로 작다는 것을 알 수 있었다.