Izzul Adli Mohd Arif
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Izzul Adli Mohd Arif has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ahmad Lutfi Anis
Faculty of Applied Sciences, Universiti Teknologi MARA, 94300 Kota Samarahan, Sarawak, Malaysia
3 shared publications - Mahesh Kumar Talari
Department of Metallurgical and Materials Engineering, National Institute of Technology, Warangal 506004, Telangana, India
3 shared publications - Muhammad Hussain Ismail
Universiti Teknologi MARA
3 shared publications N. Kishore Babu
Empa, Swiss Federal Laboratories for Material Science and Technology
2 shared publications- Gabbita Durga Janaki Ram
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai, India
1 shared publication - Nagumothu Kishore Babu
Department of Metallurgical and Materials Engineering, National Institute of Technology, Warangal, India
1 shared publication
Latest Publications
- Open Access
- 24 December 2019
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 7 (4.14) , 538-543
Effects of Boron and Carbon Added Titanium Filler on Microstructure and Mechanical Properties of Ti-15-3 Alloy Weldments
Microstructural and mechanical properties beta Titanium (β-Ti) weldments can be improved by grain refinement and formation of insoluble precipitates in the weld. This paper reports the effect of Boron (B) and Carbon (C) addition to Ti-15V-3Cr-3Sn-3Al (Ti-15-3) fillers on the microstructural and mechanical properties of Ti-15-3 gas tungsten arc weldments. X-ray diffraction and scanning electron microscopic analysis revealed the presence of β-Ti phase in the weldments prepared without the filler modification, while additional TiB and TiC phases are observed in the weldments prepared with fillers modified with B and C, respectively. B and C addition to the fillers has resulted in the grain refinement of the weldments and the grain size reduction is seen to be higher with the increasing B and C addition. The formation of TiB, TiC and growth restriction effect due to the presence of B and C in the filler resulted in the decreased grain size of the β-Ti weldments. Mechanical properties such as hardness and tensile strength improved as the amount of B and C addition increased. The improvement of mechanical properties is contributed by the grain refinement and the formation of TiB and TiC precipitates in weldments.
- 24 December 2019
- Published by Science Publishing Corporation in International Journal of Engineering & Technology
- Vol. 7 (4.14) , 538-543
Open AccessEffects of Boron and Carbon Added Titanium Filler on Microstructure and Mechanical Properties of Ti-15-3 Alloy Weldments
Microstructural and mechanical properties beta Titanium (β-Ti) weldments can be improved by grain refinement and formation of insoluble precipitates in the weld. This paper reports the effect of Boron (B) and Carbon (C) addition to Ti-15V-3Cr-3Sn-3Al (Ti-15-3) fillers on the microstructural and mechanical properties of Ti-15-3 gas tungsten arc weldments. X-ray diffraction and scanning electron microscopic analysis revealed the presence of β-Ti phase in the weldments prepared without the filler modification, while additional TiB and TiC phases are observed in the weldments prepared with fillers modified with B and C, respectively. B and C addition to the fillers has resulted in the grain refinement of the weldments and the grain size reduction is seen to be higher with the increasing B and C addition. The formation of TiB, TiC and growth restriction effect due to the presence of B and C in the filler resulted in the decreased grain size of the β-Ti weldments. Mechanical properties such as hardness and tensile strength improved as the amount of B and C addition increased. The improvement of mechanical properties is contributed by the grain refinement and the formation of TiB and TiC precipitates in weldments.
- 28 January 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 685-690
Microstructure and Mechanical Properties of Ti-15-3 Alloy Gas Tungsten Arc Welds Prepared Using CP-Titanium Filler
- 28 January 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 685-690
Microstructure and Mechanical Properties of Ti-15-3 Alloy Gas Tungsten Arc Welds Prepared Using CP-Titanium Filler
- 27 January 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 861-865
Grain Refinement, Microstructural and Hardness Investigation of C Added Ti-15-3 Alloys Prepared by Argon Arc Melting
- 27 January 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 861-865
Grain Refinement, Microstructural and Hardness Investigation of C Added Ti-15-3 Alloys Prepared by Argon Arc Melting