Radek Glaser
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Radek Glaser has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Vincent Caccese
University of Maine
4 shared publications Mohsen Shahinpoor
3 shared publicationsVincent Caccese
2 shared publications- M. Shahinpoor
University of Maine
1 shared publication
Latest Publications
- 1 January 2018
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 138, 48-65
Comparative finite element and experimental analysis of a quasi-static inflation of a thin deployable membrane space structure
- 1 January 2018
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 138, 48-65
Comparative finite element and experimental analysis of a quasi-static inflation of a thin deployable membrane space structure
- 21 January 2014
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 105 (9) , 980-997
Experimental determination of shear properties, buckling resistance and diagonal tension field of polyurethane coated nylon fabric
Experimental methods have been employed to acquire shear properties, examine buckling, and postbuckling response, and to characterize out-of-plane deformations of thin orthotropic polyurethane-coated nylon fabric designated for use in the finite element analysis of an inflatable structure. A custom-designed bi-axial pre-tension frame, a picture-fame rig, and a photogrammetry system were used to apply pre-tension, collect the angular and linear displacements, and to capture the buckling and wrinkle-forming mechanisms in the coupons during the shear test. The series of monotonic picture-frame tests provided with an average critical shear stress of 0.16 MPa that was required to buckle the coupons for a small range of the pre-tension force. While an average pre-buckling shear modulus (28.5 MPa) was obtained, only 2.25% of a relative difference between the average post-buckling apparent shear modulus (13.07 MPa) and the average shear modulus obtained from the 45° bias-extension test for the same material (13.36 MPa) was registered. The influence of the pre-tension not only on the initial buckling resistance and the transition point to the fully developed diagonal tension folds but also on a reduced resistance to the material damage during cyclic testing was investigated. A series of cyclic picture-frame tests gave the continuous load/unload response with appreciable hysteresis characteristics of the in-plane stress–strain with an average 10% of material degradation. When compared with the envelope of material resistance in the monotonic tests, during cycling loading, the coupons lost on average 13.9% more of its initial stress-carrying capability. The photogrammetry results allowed for the three-dimensional reconstruction of the coupon’s surface and the development of the deformation relationships between the effective force exerted on the coupons, the shear angle, and the geometric deformation variables for the wrinkles formed in the diagonal tension fold. The geometric deformation parameters, such as frequency of wrinkle formation, widths of the base and the tip, depths, the deformation angle, and the distances between the centerlines of the wrinkles occurring in the test coupon, were acquired with photogrametry and analyzed numerically with custom-written Matlab® code.
- 21 January 2014
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 105 (9) , 980-997
Experimental determination of shear properties, buckling resistance and diagonal tension field of polyurethane coated nylon fabric
Experimental methods have been employed to acquire shear properties, examine buckling, and postbuckling response, and to characterize out-of-plane deformations of thin orthotropic polyurethane-coated nylon fabric designated for use in the finite element analysis of an inflatable structure. A custom-designed bi-axial pre-tension frame, a picture-fame rig, and a photogrammetry system were used to apply pre-tension, collect the angular and linear displacements, and to capture the buckling and wrinkle-forming mechanisms in the coupons during the shear test. The series of monotonic picture-frame tests provided with an average critical shear stress of 0.16 MPa that was required to buckle the coupons for a small range of the pre-tension force. While an average pre-buckling shear modulus (28.5 MPa) was obtained, only 2.25% of a relative difference between the average post-buckling apparent shear modulus (13.07 MPa) and the average shear modulus obtained from the 45° bias-extension test for the same material (13.36 MPa) was registered. The influence of the pre-tension not only on the initial buckling resistance and the transition point to the fully developed diagonal tension folds but also on a reduced resistance to the material damage during cyclic testing was investigated. A series of cyclic picture-frame tests gave the continuous load/unload response with appreciable hysteresis characteristics of the in-plane stress–strain with an average 10% of material degradation. When compared with the envelope of material resistance in the monotonic tests, during cycling loading, the coupons lost on average 13.9% more of its initial stress-carrying capability. The photogrammetry results allowed for the three-dimensional reconstruction of the coupon’s surface and the development of the deformation relationships between the effective force exerted on the coupons, the shear angle, and the geometric deformation variables for the wrinkles formed in the diagonal tension fold. The geometric deformation parameters, such as frequency of wrinkle formation, widths of the base and the tip, depths, the deformation angle, and the distances between the centerlines of the wrinkles occurring in the test coupon, were acquired with photogrametry and analyzed numerically with custom-written Matlab® code.
- 8 January 2013
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 104 (7) , 682-698
Experimental methods to determine in-plane material properties of polyurethane-coated nylon fabric
Experimental procedures have been developed to obtain the mechanical stiffness and strength properties of an orthotropic polyurethane-coated nylon fabric for use in a finite element analysis of an inflatable, deployable structure. A method that utilizes a specialized material test fixture and photogrammetry to collect the linear and angular displacement data has been employed. Different material holding methods were compared with the objective of producing strength values not influenced by gripping and that allow for use of machine displacement to estimate longitudinal strains during cyclic testing. A series of tension and bias tension tests provided material properties such as Young’s modulus in both warp and fill directions, Poisson’s ratios in plane and through the thickness, and shear modulus. Results obtained from the photogrammetry method show good correlation to machine readings using a pinched gripping method. Additionally, cyclic tests gave the continuous load–unload response and the hysteresis characteristics of the stress–strain in plane and indicated the degree of material degradation. The shear stress–shear strain behavior and shear modulus values are acquired using bias tension tests on 45° skewed specimens.
- 8 January 2013
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 104 (7) , 682-698
Experimental methods to determine in-plane material properties of polyurethane-coated nylon fabric
Experimental procedures have been developed to obtain the mechanical stiffness and strength properties of an orthotropic polyurethane-coated nylon fabric for use in a finite element analysis of an inflatable, deployable structure. A method that utilizes a specialized material test fixture and photogrammetry to collect the linear and angular displacement data has been employed. Different material holding methods were compared with the objective of producing strength values not influenced by gripping and that allow for use of machine displacement to estimate longitudinal strains during cyclic testing. A series of tension and bias tension tests provided material properties such as Young’s modulus in both warp and fill directions, Poisson’s ratios in plane and through the thickness, and shear modulus. Results obtained from the photogrammetry method show good correlation to machine readings using a pinched gripping method. Additionally, cyclic tests gave the continuous load–unload response and the hysteresis characteristics of the stress–strain in plane and indicated the degree of material degradation. The shear stress–shear strain behavior and shear modulus values are acquired using bias tension tests on 45° skewed specimens.
- 10 December 2012
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 22 (1)
Development of novel smart MR-gates for wireless dynamic control of fluid flow
- 10 December 2012
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 22 (1)
Development of novel smart MR-gates for wireless dynamic control of fluid flow
- 14 July 2011
- Published by Springer Nature in Experimental Mechanics
- Vol. 52 (6) , 591-606
Shape Monitoring of a Beam Structure from Measured Strain or Curvature
- 14 July 2011
- Published by Springer Nature in Experimental Mechanics
- Vol. 52 (6) , 591-606
Shape Monitoring of a Beam Structure from Measured Strain or Curvature
- 28 March 2011
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 20 (4)
Development of magneto-rheological fluid composites with rigidification characteristics
- 28 March 2011
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 20 (4)
Development of magneto-rheological fluid composites with rigidification characteristics