Ihor Dudnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ihor Dudnikov has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Dudnikov
Poltava State Agrarian University
2 shared publications - Mykola Shevchuk
Lutsk National Technical University
2 shared publications A. Kuzmich
1 shared publication- Anatoliі Antonets
Poltava State Agrarian University
1 shared publication - Anton Kelemesh
Полтавський державний аграрний університет
1 shared publication - Ihor Marynchenko
Institute of Bast Crops NAAS
1 shared publication
Latest Publications
- Open Access
- 13 October 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(61)) , 6-11
Increasing the resource of agricultural machines
The object of research is the technological process of increasing the service life of pointed cultivator shares of tillage machines through the use of a progressive method of vibration hardening. One of the most problematic areas is the inadequate study of the investigated technological process of restoring the working bodies of agricultural machines. In order to gain a deeper understanding of the process of vibration processing of the material of these machine parts during their restoration, it is necessary to conduct further experimental studies. In the course of the study, it has been found that the use of vibration deformation of the surface layer of the material of parts contributes to an increase in their resource. The optimal parameters of vibration hardening of the cutting elements of the cultivator shares of tillage machines have been determined, which makes it possible to increase their durability. The main parameters of vibration hardening are revealed: the vibration amplitude of the processing tool is 0.75 mm; vibration frequency – 1400 min–1; hardening time – 30 s. As a research result, the assessment of the change in linear wear along the width of the cutting element of the cultivator duckfoot of tillage machines was carried out. In cultivators with tines restored by welding angle plates made of 45 steel (GOST 1050-2013, GB 699-88), sormite surfacing and vibration hardening, the linear wear rate by weight of cutting elements is 35–43 % less than in new tines. A study of changes in the wear of the cutting edge of cultivator shares was carried out, which, when restored by welding corner plates made of steel 45 (GOST 1050-2013, GB 699-88), surfacing with sormite and vibration hardening, is 1.57–1.68 times less than in new shares. In comparison with existing technologies, the developed technology provides a reduction in the wear of cutting elements by 10–17 %, in comparison with new ones made of 65G steel (GOST 14959-2016, GB 1222). The coefficient of technical utilization of the cultivator with tines restored according to the developed technology, in comparison with the new ones, is 1.07 times higher.
- 13 October 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(61)) , 6-11
Open AccessIncreasing the resource of agricultural machines
The object of research is the technological process of increasing the service life of pointed cultivator shares of tillage machines through the use of a progressive method of vibration hardening. One of the most problematic areas is the inadequate study of the investigated technological process of restoring the working bodies of agricultural machines. In order to gain a deeper understanding of the process of vibration processing of the material of these machine parts during their restoration, it is necessary to conduct further experimental studies. In the course of the study, it has been found that the use of vibration deformation of the surface layer of the material of parts contributes to an increase in their resource. The optimal parameters of vibration hardening of the cutting elements of the cultivator shares of tillage machines have been determined, which makes it possible to increase their durability. The main parameters of vibration hardening are revealed: the vibration amplitude of the processing tool is 0.75 mm; vibration frequency – 1400 min–1; hardening time – 30 s. As a research result, the assessment of the change in linear wear along the width of the cutting element of the cultivator duckfoot of tillage machines was carried out. In cultivators with tines restored by welding angle plates made of 45 steel (GOST 1050-2013, GB 699-88), sormite surfacing and vibration hardening, the linear wear rate by weight of cutting elements is 35–43 % less than in new tines. A study of changes in the wear of the cutting edge of cultivator shares was carried out, which, when restored by welding corner plates made of steel 45 (GOST 1050-2013, GB 699-88), surfacing with sormite and vibration hardening, is 1.57–1.68 times less than in new shares. In comparison with existing technologies, the developed technology provides a reduction in the wear of cutting elements by 10–17 %, in comparison with new ones made of 65G steel (GOST 14959-2016, GB 1222). The coefficient of technical utilization of the cultivator with tines restored according to the developed technology, in comparison with the new ones, is 1.07 times higher.
- Open Access
- 30 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (111)) , 100-112
Building an analytical model of the gravitational grain movement in an open screw channel with variable inclination angles
Existing technical means for loading silos with grain material do not fully meet the needs of production. The issue related to grain injury remains urgent, which predetermines the need to design a gravitational loader of another principle of operation with the appropriate theoretical justification for the movement of grain material in it. This paper has presented and substantiated the model of the gravitational movement of grain in the peripheral open screw channel with two variable angles of inclination. The model is based on the system of forces in the cylindrical coordinate system, acting on the volume of grain flow in the peripheral screw channel. The grain speed at the end of the braking section of the channel should be as low as possible but not less than the initial flow rate at the beginning of the acceleration section. The model takes into consideration this condition and ensures the optimal passage of grain along any part of the channel. The reported model makes it possible to obtain the speed of grain movement at any time, takes into consideration the height of the bunker hole and the dependence between the angles of inclination of the spirals of acceleration and brake sections. A mathematical dependence is given for these angles that ensures the passage of grain without its discharge and, at the same time, prevents injury to the grain mass due to a controlled decrease in the resulting speed. A separate dependence is provided to find the time at which the grain increases its speed on the acceleration section, reaching the maximum value. Based on the model, a peripheral open screw channel with two angles of inclination of spirals α and β has been proposed. For this channel, the relationships between its key parameters have been established, in particular, values have been substantiated for the recommended angles of 41°…45° for the acceleration section and 39°…35° for the brake section, respectively, as well as the hо/r ratio not less than 0.6...0.7.
- 30 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (111)) , 100-112
Open AccessBuilding an analytical model of the gravitational grain movement in an open screw channel with variable inclination angles
Existing technical means for loading silos with grain material do not fully meet the needs of production. The issue related to grain injury remains urgent, which predetermines the need to design a gravitational loader of another principle of operation with the appropriate theoretical justification for the movement of grain material in it. This paper has presented and substantiated the model of the gravitational movement of grain in the peripheral open screw channel with two variable angles of inclination. The model is based on the system of forces in the cylindrical coordinate system, acting on the volume of grain flow in the peripheral screw channel. The grain speed at the end of the braking section of the channel should be as low as possible but not less than the initial flow rate at the beginning of the acceleration section. The model takes into consideration this condition and ensures the optimal passage of grain along any part of the channel. The reported model makes it possible to obtain the speed of grain movement at any time, takes into consideration the height of the bunker hole and the dependence between the angles of inclination of the spirals of acceleration and brake sections. A mathematical dependence is given for these angles that ensures the passage of grain without its discharge and, at the same time, prevents injury to the grain mass due to a controlled decrease in the resulting speed. A separate dependence is provided to find the time at which the grain increases its speed on the acceleration section, reaching the maximum value. Based on the model, a peripheral open screw channel with two angles of inclination of spirals α and β has been proposed. For this channel, the relationships between its key parameters have been established, in particular, values have been substantiated for the recommended angles of 41°…45° for the acceleration section and 39°…35° for the brake section, respectively, as well as the hо/r ratio not less than 0.6...0.7.
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51
Research of Conditions of Cutting of Stalks with Sliding
Viktor Sheichenko, Professor, Doctor in Technics (Doctor of Technics Sciences), Poltava State Agrarian University, Poltava, Ukraine, e–mail: vsheychenko@ukr.net, ORCID ID: 0000-0003-2751-6181 Igor Dudnikov, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Poltava State Agrarian University, Poltava, Ukraine, ORCID ID: 0000-0002-0448-2241 Vitaliy Shevchuk, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Uman National University of Horticulture, Uman, Ukraine, e–mail: shevchuk16111@ukr.net, ORCID ID: 0000-0001-8305-4714 Viktor Shevchuk, Lecturer-Methodologist, Highest Category, Uman Vocational College of Technology and Business, Uman National University of Horticulture, Uman, Ukraine Abstract Features of cutting of a stalk by a blade with sliding are analytically investigated. The conditions of cutting with sliding of a horizontally located stalk with a knife are substantiated, according to which the blade must press on the stalk perpendicular to it and move at an angle ξ to the normal. The marked angle must be greater than the friction angle φ. The limits of change of values of the angle ξ at which cutting of stalks with sliding is possible are analyzed and defined. It is noted that to ensure cutting of the stem with sliding, as well as to simultaneously and rationally reduce the sliding time of the blade on the stem, it is advisable to perform the operation of cutting stems at an angle ξ less than 90 °. The dependence determined by the conditions of observance by the angle ξp of the zone of the desired action of the velocity point of the blade point to ensure cutting of the stems with sliding is established. The theoretical dependence for determining the sliding coefficient is established, which allows to numerically estimate the degree of sliding. It is noted that cutting with sliding requires less force N, less normal pressure than non-slip cutting. Under such conditions, an increase in the angle ξ leads to a corresponding decrease in the force N. The implementation of the results of the study in the cutting machines of harvesters, forage machines, as well as segmental cutters of reciprocating movement of harvesters, will allow due to the quality of the technological process of cutting plant stems with sliding increase in productivity up to 17%. Keywords sliding cutting, sliding coefficient, sliding cutting conditions Full Text: PDF References 1. Zheligovskij, V.A. (1960). Jelementy teorii pochvoobrabatyvajushhih mashin i mehanicheskoj tehnologii sel'skohozjajstvennyh materialov [Elements of the theory of tillage machines and mechanical technology of agricultural materials] Tbilisi, Izd. GSHI 1201 [in Russian]. 2. Bosoj, E.S. (1967). Rezhushhie apparaty uborochnyh mashin [Cutting devices of harvesting machines]. Moscow. Mashinostroenie [in Russian]. 3. Zaika, P.M. Teorіjasіl's'kogospodars'kih mashin. Mashini dlja zagotіvlіkormіv [Theory of agricultural machinery. Machines for forage harvesting]. V.II. Kharkiv: OKO [in Russian]. 4. Reznik, N.E. (1975). Teorija rezanija lezviem i osnovy rascheta rezhushhih apparatov [The theory of cutting with a blade and the basics of calculating cutting devices]. Moscow. Mashinostroenie [in Russian]. 5. Ivashko, A.A. (1958). Voprosy teorii rezanija organicheskih materialov lezviem [Questions of the theory of cutting organic materials with a blade]. Traktory i sel'hozmashiny – Tractors and Agricultural Machines, 2, 34-37 [in Russian]. 6. Vasilenko, I.F. (1937). Teorija rezhushhih apparatov zhatvennyh mashin[Theory of cutting devices of reaping machines]. Trudy VISHOM – - Proceedings of VISKHOM. Sat. 5. Moskva [in Russian]. 1201 [in Russian]. 7. Zhang, Y., Cui, Q., Li, H., Zhang, Z., He, Y. & Sun, D. (2020). Simulation and test of cutting mechanical characteristics of millet stalk based on ANSYS/LS-DYNA . INMATEH - Agricultural Engineering, 61 (2), pp. 143-150. DOI: 10.35633/inmateh-61-16 [in English]. 8. Zhang, C.L., Chen, L.Q., Xia, J.F. & Zhang, J.M. (2019). Effects of blade sliding cutting angle and stem level on cutting еgenergy of rice stems. International Journal of Agricultural and Biological Engineering, 12 (6), pp. 75-81. DOI: 10.25165/j.ijabe.20191206.4604. [in English]. 9. Zhang, Y., Cui, Q., Li, H., Sun, D., Hou, H. (2018). Effects of stem region, moisture content and blade oblique angle on mechanical cutting of millet stems. INMATEH - Agricultural Engineering, 55 (2), pp. 105-112. ISSN20684215 [in English]. 10. Tian, K., Li, X., Shen, C., Zhang, B., Huang, J., Wang, J., Zhou, Y. (2017). Designand test of cutting blade of cannabis harvester based on longicorn bionic principle Nongye Gongcheng Xuebao . Transactionsof the Chinese Society of Agricultural Engineering, 33 (5), pp. 56-61. DOI: 10.11975/j.issn.1002-6819.2017.05.008 [in English]. 11. Klenin, N.I. & Sakun, V.A. (1980). Sel'skohozjajstvennye i meliorativnye mashiny [Agricultural and reclamation machines]. Moscow [in Russian]. 12. Letoshnev, M.N. (1955). Sel'skohozjajstvennye mashiny [Agreecultural machines] Moscow. L. Gos. izd. s.-h. literatury [in Russian]. 13. Osobov V.I. (2009). Mehanicheskaja tehnologija kormov [Mechanical feed technology]. Moscow. Kolos [in Russian]. 14. Hajlis, G.A. (1992). Osnovy teorii i rascheta sel'skohozjajstvennyh mashin [Fundamentals of the theory and calculation of agricultural machines]. Kiev, Izd-vo USHA, 1992. 235 s. 1201 [in Russian]. Citations Желиговский В.А. Элементы теории почвообрабатывающих машин и механической технологии сельскохозяйственных материалов. Тбилиси, Изд. ГСХИ, 1960. 146 с. Босой Е.С. Режущие аппараты уборочных машин. Москва. Машиностроение, 1967. 167 с. Заика П.М. Теоріясільськогосподарських машин. Т. ІІ. Машини для заготівлікормів. Харків. ОКО, 2003. 345 с. Резник Н.Е. Теория резания лезвием и основы расчета режущих аппаратов. Москва. Машиностроение, 1975. 303 с. Ивашко А.А. Вопросы теории резания органических материалов лезвием. Тракторы и сельхозмашины. 1958. № 2. С. 34-37. Василенко И.Ф. Теория режущих аппаратов жатвенных машин. Труды ВИСХОМ. Сб. 5. Москва, 1937. С. 7-114. Zhang, Y., Cui, Q., Li, H., Zhang, Z., He, Y., Sun, D. Simulation and test of cutting mechanical characteristics of millet stalk based on ANSYS/LS-DYNA. INMATEH - Agricultural Engineering. 2020. 61 (2). Pp. 143-150. DOI: 10.35633/inmateh-61-16 Zhang, C.L., Chen, L.Q., Xia, J.F., Zhang, J.M. Effects of blade sliding cutting angle and stem level on cutting еgenergy of rice stems. International Journal of Agricultural and Biological Engineering. 2019 12 (6). Рp. 75-81. DOI: 10.25165/j.ijabe.20191206.4604. Zhang, Y., Cui, Q., Li, H., Sun, D., Hou, H. Effects of stem region, moisture content and blade oblique angle on mechanical cutting of millet stems. INMATEH - Agricultural Engineering. 2018. 55 (2). Pp. 105-112. ISSN20684215 Tian, K., Li, X., Shen, C., Zhang, B., Huang, J., Wang, J., Zhou, Y. Designand test of cutting blade of cannabis harvester based on longicorn bionic principle. Nongye Gongcheng Xuebao. Transactionsof the Chinese Society of Agricultural Engineering. 2017. 33 (5). Pp. 56-61. DOI: 10.11975/j.issn.1002-6819.2017.05.008 Кленин Н.И., Сакун В.А. Сельскохозяйственные и мелиоративные машины. Москва: Колос, 1980. С. 72-78. Летошнев М.Н. Сельскохозяйственные машины. Москва. Л. Гос. изд. с.-х. литературы, 1955. Особов В.И. Механическая технология кормов. Москва. Колос, 2009. 339 с. Хайлис Г.А. Основы теории и расчета сельскохозяйственных машин. Киев, Изд-во УСХА, 1992. 235 с. Copyright (c) 2021 Viktor Sheichenko, Igor Dudnikov, Vitaliy Shevchuk, Viktor Shevchuk
- 1 January 2021
- Published by Central Ukrainian National Technical University in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
- No. 51
Research of Conditions of Cutting of Stalks with Sliding
Viktor Sheichenko, Professor, Doctor in Technics (Doctor of Technics Sciences), Poltava State Agrarian University, Poltava, Ukraine, e–mail: vsheychenko@ukr.net, ORCID ID: 0000-0003-2751-6181 Igor Dudnikov, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Poltava State Agrarian University, Poltava, Ukraine, ORCID ID: 0000-0002-0448-2241 Vitaliy Shevchuk, Associate Professor, PhD in Technics (Candidate of Technics Sciences), Uman National University of Horticulture, Uman, Ukraine, e–mail: shevchuk16111@ukr.net, ORCID ID: 0000-0001-8305-4714 Viktor Shevchuk, Lecturer-Methodologist, Highest Category, Uman Vocational College of Technology and Business, Uman National University of Horticulture, Uman, Ukraine Abstract Features of cutting of a stalk by a blade with sliding are analytically investigated. The conditions of cutting with sliding of a horizontally located stalk with a knife are substantiated, according to which the blade must press on the stalk perpendicular to it and move at an angle ξ to the normal. The marked angle must be greater than the friction angle φ. The limits of change of values of the angle ξ at which cutting of stalks with sliding is possible are analyzed and defined. It is noted that to ensure cutting of the stem with sliding, as well as to simultaneously and rationally reduce the sliding time of the blade on the stem, it is advisable to perform the operation of cutting stems at an angle ξ less than 90 °. The dependence determined by the conditions of observance by the angle ξp of the zone of the desired action of the velocity point of the blade point to ensure cutting of the stems with sliding is established. The theoretical dependence for determining the sliding coefficient is established, which allows to numerically estimate the degree of sliding. It is noted that cutting with sliding requires less force N, less normal pressure than non-slip cutting. Under such conditions, an increase in the angle ξ leads to a corresponding decrease in the force N. The implementation of the results of the study in the cutting machines of harvesters, forage machines, as well as segmental cutters of reciprocating movement of harvesters, will allow due to the quality of the technological process of cutting plant stems with sliding increase in productivity up to 17%. Keywords sliding cutting, sliding coefficient, sliding cutting conditions Full Text: PDF References 1. Zheligovskij, V.A. (1960). Jelementy teorii pochvoobrabatyvajushhih mashin i mehanicheskoj tehnologii sel'skohozjajstvennyh materialov [Elements of the theory of tillage machines and mechanical technology of agricultural materials] Tbilisi, Izd. GSHI 1201 [in Russian]. 2. Bosoj, E.S. (1967). Rezhushhie apparaty uborochnyh mashin [Cutting devices of harvesting machines]. Moscow. Mashinostroenie [in Russian]. 3. Zaika, P.M. Teorіjasіl's'kogospodars'kih mashin. Mashini dlja zagotіvlіkormіv [Theory of agricultural machinery. Machines for forage harvesting]. V.II. Kharkiv: OKO [in Russian]. 4. Reznik, N.E. (1975). Teorija rezanija lezviem i osnovy rascheta rezhushhih apparatov [The theory of cutting with a blade and the basics of calculating cutting devices]. Moscow. Mashinostroenie [in Russian]. 5. Ivashko, A.A. (1958). Voprosy teorii rezanija organicheskih materialov lezviem [Questions of the theory of cutting organic materials with a blade]. Traktory i sel'hozmashiny – Tractors and Agricultural Machines, 2, 34-37 [in Russian]. 6. Vasilenko, I.F. (1937). Teorija rezhushhih apparatov zhatvennyh mashin[Theory of cutting devices of reaping machines]. Trudy VISHOM – - Proceedings of VISKHOM. Sat. 5. Moskva [in Russian]. 1201 [in Russian]. 7. Zhang, Y., Cui, Q., Li, H., Zhang, Z., He, Y. & Sun, D. (2020). Simulation and test of cutting mechanical characteristics of millet stalk based on ANSYS/LS-DYNA . INMATEH - Agricultural Engineering, 61 (2), pp. 143-150. DOI: 10.35633/inmateh-61-16 [in English]. 8. Zhang, C.L., Chen, L.Q., Xia, J.F. & Zhang, J.M. (2019). Effects of blade sliding cutting angle and stem level on cutting еgenergy of rice stems. International Journal of Agricultural and Biological Engineering, 12 (6), pp. 75-81. DOI: 10.25165/j.ijabe.20191206.4604. [in English]. 9. Zhang, Y., Cui, Q., Li, H., Sun, D., Hou, H. (2018). Effects of stem region, moisture content and blade oblique angle on mechanical cutting of millet stems. INMATEH - Agricultural Engineering, 55 (2), pp. 105-112. ISSN20684215 [in English]. 10. Tian, K., Li, X., Shen, C., Zhang, B., Huang, J., Wang, J., Zhou, Y. (2017). Designand test of cutting blade of cannabis harvester based on longicorn bionic principle Nongye Gongcheng Xuebao . Transactionsof the Chinese Society of Agricultural Engineering, 33 (5), pp. 56-61. DOI: 10.11975/j.issn.1002-6819.2017.05.008 [in English]. 11. Klenin, N.I. & Sakun, V.A. (1980). Sel'skohozjajstvennye i meliorativnye mashiny [Agricultural and reclamation machines]. Moscow [in Russian]. 12. Letoshnev, M.N. (1955). Sel'skohozjajstvennye mashiny [Agreecultural machines] Moscow. L. Gos. izd. s.-h. literatury [in Russian]. 13. Osobov V.I. (2009). Mehanicheskaja tehnologija kormov [Mechanical feed technology]. Moscow. Kolos [in Russian]. 14. Hajlis, G.A. (1992). Osnovy teorii i rascheta sel'skohozjajstvennyh mashin [Fundamentals of the theory and calculation of agricultural machines]. Kiev, Izd-vo USHA, 1992. 235 s. 1201 [in Russian]. Citations Желиговский В.А. Элементы теории почвообрабатывающих машин и механической технологии сельскохозяйственных материалов. Тбилиси, Изд. ГСХИ, 1960. 146 с. Босой Е.С. Режущие аппараты уборочных машин. Москва. Машиностроение, 1967. 167 с. Заика П.М. Теоріясільськогосподарських машин. Т. ІІ. Машини для заготівлікормів. Харків. ОКО, 2003. 345 с. Резник Н.Е. Теория резания лезвием и основы расчета режущих аппаратов. Москва. Машиностроение, 1975. 303 с. Ивашко А.А. Вопросы теории резания органических материалов лезвием. Тракторы и сельхозмашины. 1958. № 2. С. 34-37. Василенко И.Ф. Теория режущих аппаратов жатвенных машин. Труды ВИСХОМ. Сб. 5. Москва, 1937. С. 7-114. Zhang, Y., Cui, Q., Li, H., Zhang, Z., He, Y., Sun, D. Simulation and test of cutting mechanical characteristics of millet stalk based on ANSYS/LS-DYNA. INMATEH - Agricultural Engineering. 2020. 61 (2). Pp. 143-150. DOI: 10.35633/inmateh-61-16 Zhang, C.L., Chen, L.Q., Xia, J.F., Zhang, J.M. Effects of blade sliding cutting angle and stem level on cutting еgenergy of rice stems. International Journal of Agricultural and Biological Engineering. 2019 12 (6). Рp. 75-81. DOI: 10.25165/j.ijabe.20191206.4604. Zhang, Y., Cui, Q., Li, H., Sun, D., Hou, H. Effects of stem region, moisture content and blade oblique angle on mechanical cutting of millet stems. INMATEH - Agricultural Engineering. 2018. 55 (2). Pp. 105-112. ISSN20684215 Tian, K., Li, X., Shen, C., Zhang, B., Huang, J., Wang, J., Zhou, Y. Designand test of cutting blade of cannabis harvester based on longicorn bionic principle. Nongye Gongcheng Xuebao. Transactionsof the Chinese Society of Agricultural Engineering. 2017. 33 (5). Pp. 56-61. DOI: 10.11975/j.issn.1002-6819.2017.05.008 Кленин Н.И., Сакун В.А. Сельскохозяйственные и мелиоративные машины. Москва: Колос, 1980. С. 72-78. Летошнев М.Н. Сельскохозяйственные машины. Москва. Л. Гос. изд. с.-х. литературы, 1955. Особов В.И. Механическая технология кормов. Москва. Колос, 2009. 339 с. Хайлис Г.А. Основы теории и расчета сельскохозяйственных машин. Киев, Изд-во УСХА, 1992. 235 с. Copyright (c) 2021 Viktor Sheichenko, Igor Dudnikov, Vitaliy Shevchuk, Viktor Shevchuk
- Open Access
- 14 November 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1) , 26-32
Improving the technology of part machining by surface plastic deformation
- 14 November 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1) , 26-32
Open AccessImproving the technology of part machining by surface plastic deformation
- Open Access
- 1 May 2019
- Published by Independent Journal of Management and Production in Independent Journal of Management & Production
- Vol. 10 (7) , 687-701
Development of technology for the hemp stalks preparation
Getting high-quality trusts in modern technology for growing technical hemp is one of the most labor-intensive processes.The main factors that cause loss of quality of hemp are determined by the level of perfection of the harvesting stage of the production process. It is precisely at this stage that the basic processes of product quality management are concentrated, the main physical and technological losses are taking place.The main drawbacks of the known methods of obtaining the trusts of technical hemp include the dependence of the process of forming its qualitative indicators on weather conditions, the unevenness of the separation and strength of the fiber on the entire mass of the sent layer, the length of the technological process, which determines the quantitative loss of production.The article presents the results of research on the development of resource-saving technology for the production of technical hemp trusts due to the addition of an outlet with improved water drains with reeds and finger-wheels and the direct effect of their constructive parameters on the quality indicators of the trust.Mechanized technological processes are carried out thanks to the developed unit, which includes: a modernized corrugated water pump, hay rakes and a roll baler.It was noted that an increase in the number of mechanical influences on the hemp strap ribbon leads to a corresponding decrease in its height and mass. The loosening process reduces the weight of the tape to 2.1 kg per linear meter. Under these conditions, the height of the windrow increases to 35.0 cm. Techniques for obtaining a hedge trustee make it possible to reduce the time of process implementation at the initial stages of its preparation for primary processing, intensifies the process of purification due to the additional mechanical drive with improved aggregates. The short fiber obtained from the hemp trust for the technology developed meets the existing requirements.
- 1 May 2019
- Published by Independent Journal of Management and Production in Independent Journal of Management & Production
- Vol. 10 (7) , 687-701
Open AccessDevelopment of technology for the hemp stalks preparation
Getting high-quality trusts in modern technology for growing technical hemp is one of the most labor-intensive processes.The main factors that cause loss of quality of hemp are determined by the level of perfection of the harvesting stage of the production process. It is precisely at this stage that the basic processes of product quality management are concentrated, the main physical and technological losses are taking place.The main drawbacks of the known methods of obtaining the trusts of technical hemp include the dependence of the process of forming its qualitative indicators on weather conditions, the unevenness of the separation and strength of the fiber on the entire mass of the sent layer, the length of the technological process, which determines the quantitative loss of production.The article presents the results of research on the development of resource-saving technology for the production of technical hemp trusts due to the addition of an outlet with improved water drains with reeds and finger-wheels and the direct effect of their constructive parameters on the quality indicators of the trust.Mechanized technological processes are carried out thanks to the developed unit, which includes: a modernized corrugated water pump, hay rakes and a roll baler.It was noted that an increase in the number of mechanical influences on the hemp strap ribbon leads to a corresponding decrease in its height and mass. The loosening process reduces the weight of the tape to 2.1 kg per linear meter. Under these conditions, the height of the windrow increases to 35.0 cm. Techniques for obtaining a hedge trustee make it possible to reduce the time of process implementation at the initial stages of its preparation for primary processing, intensifies the process of purification due to the additional mechanical drive with improved aggregates. The short fiber obtained from the hemp trust for the technology developed meets the existing requirements.
- 1 January 2019
- Published by National Scientific Center - Institute of Agricultural Engineering and Electrification in Mehanization and electrification of agricultural
- No. 9(108),p. 72-80
Investigation effect of the throughput combine on the quality of grain separated by a preliminary threshing device
Purpose. Improving the efficiency of the combine harvester by establishing the effect its throughput (thresher loading) on the quality indicators of the grain separated by a preliminary threshing device. Methods. Experimental researches were carried out using the method planning and conducting single-factor experiments. The processing of experimental results was carried out taking into account the methods by regression analysis. The approximation of the experimental dependencies by the mathematical model was performed using the least squares method using the statistical software package STATISTIKA-6.5. Results. A combined technological process transportation and threshing of grain-straw mass (GSM) was developed, which is based on a preliminary threshing device and takes into account the differences in the interaction of GSM with the device drum bars. The identity the processes change in the energy of germination and seed germination culture germination depending on the level loading for all the considered device options is noted. For each device option, a rational value throughput is established, which corresponds to a high level of germination energy. Conclusions. The highest germination energy level harvested grain is 99% set for a header, the drum of which contains four strips, when the combine thresher is loaded at 7.5 kg/s. For a serial header, a high germination rate of 92% is set when the thresher is loaded at 8.5–9.5 kg/s; for a header with a preliminary threshing device with a whip under the drum at 97% when loading 6–7 kg/s; for a header with a smooth drum 94.0–94.5% with a threshing load of 8–9 kg/s; for the reaper, the drum of which contains two strips about 95% when loading the thresher 3–4 kg/s, respectively. Comparing with the serial, for a header with the four slats drum, a higher 7% level of seed germination has been noted with a slight (1.0–1.5 kg/s) reduction in the capacity of the combine. Keywords: combine harvester, header, device for preliminary threshing of grain, grain-straw mass, germination energy, seed germination.
- 1 January 2019
- Published by National Scientific Center - Institute of Agricultural Engineering and Electrification in Mehanization and electrification of agricultural
- No. 9(108),p. 72-80
Investigation effect of the throughput combine on the quality of grain separated by a preliminary threshing device
Purpose. Improving the efficiency of the combine harvester by establishing the effect its throughput (thresher loading) on the quality indicators of the grain separated by a preliminary threshing device. Methods. Experimental researches were carried out using the method planning and conducting single-factor experiments. The processing of experimental results was carried out taking into account the methods by regression analysis. The approximation of the experimental dependencies by the mathematical model was performed using the least squares method using the statistical software package STATISTIKA-6.5. Results. A combined technological process transportation and threshing of grain-straw mass (GSM) was developed, which is based on a preliminary threshing device and takes into account the differences in the interaction of GSM with the device drum bars. The identity the processes change in the energy of germination and seed germination culture germination depending on the level loading for all the considered device options is noted. For each device option, a rational value throughput is established, which corresponds to a high level of germination energy. Conclusions. The highest germination energy level harvested grain is 99% set for a header, the drum of which contains four strips, when the combine thresher is loaded at 7.5 kg/s. For a serial header, a high germination rate of 92% is set when the thresher is loaded at 8.5–9.5 kg/s; for a header with a preliminary threshing device with a whip under the drum at 97% when loading 6–7 kg/s; for a header with a smooth drum 94.0–94.5% with a threshing load of 8–9 kg/s; for the reaper, the drum of which contains two strips about 95% when loading the thresher 3–4 kg/s, respectively. Comparing with the serial, for a header with the four slats drum, a higher 7% level of seed germination has been noted with a slight (1.0–1.5 kg/s) reduction in the capacity of the combine. Keywords: combine harvester, header, device for preliminary threshing of grain, grain-straw mass, germination energy, seed germination.