Massimiliano Polichetti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Massimiliano Polichetti has a total of 391 co-authors. Here are the top co-authors by number of shared publications:
- Armando Galluzzi
University of Salerno
60 shared publications S. Pace
Department of Physics “E.R. Caianiello”, University of Salerno, Fisciano, Italy
39 shared publications- Danilo Zola
ENEA (Italy)
24 shared publications - Gaia Grimaldi
CNR-SPIN Salerno, via Giovanni Paolo II, 132, 84084 Fisciano, Italy
21 shared publications S Pace
20 shared publications- Krastyo Buchkov
Institute of Solid State Physics, Bulgarian Academy of Sciences, 72 Tzarigradsko Chaussee blvd., 1784 Sofia, Bulgaria
16 shared publications
Latest Publications
- Open Access
- 18 November 2026
- Published by IOP Publishing in Superconductor Science and Technology
A general unit-invariance theorem for the bean relation: Toward structurally invariant expressions for magnetization-derived critical current density of rectangular parallelepiped samples in perpendicular field
The determination of the critical current density Jc from magnetization hysteresis measurements in superconductors is routinely performed using analytical expressions derived from the Bean critical state model. For rectangular parallelepiped samples in a perpendicular magnetic field, two numerical prefactors, 2 and 20, are commonly reported in the literature. These formulations are often regarded as equivalent representations differing only by unit conventions. However, while the prefactor 2 is universally treated as dimensionless, the prefactor 20 is considered implicitly dimensional or sometimes appears with explicit dimensions. In this paper, we examine the presence of dimensions in this prefactor and discuss the implications associated with the use of the corresponding expression. By proving that only structurally invariant formulations remain unchanged under arbitrary coherent transformations of units, this work provides a rigorous criterion to distinguish universal geometrical expressions from convention-dependent ones. In particular, we establish a general unit-invariance theorem and demonstrate that the prefactor 2, which emerges uniquely from geometrical integration of the critical current distribution, is invariant under arbitrary coherent transformations of units. By contrast, the prefactor 20 which tacitly implies the dimensions [A cm2/emu], and arises within a hybrid CGS electromagnetic framework through the incorporation of specific electromagnetic conversion factors into the geometrical relation, is not invariant under unit transformations. The present discussion addresses invariance at the level of physical quantities, rather than mere numerical equivalence within fixed conventions. Our analysis illustrates how retaining the prefactor 20 outside its native unit framework may introduce systematic numerical deviations when the units of the physical quantities are modified without explicit re-derivation of the coefficient. These deviations do not reflect limitations of the critical state model itself, but rather the convention-dependent nature of hybrid prefactors. We emphasize that calculating the correct value is not a matter of choosing a particular electromagnetic unit system. However, expressions that embed conversion factors within numerical coefficients are inherently unit-dependent and may reduce transparency. For methodological robustness, reproducibility, and reliable comparison of data obtained by different groups and experimental systems, the structurally invariant formulation of the Bean relation provides a more transparent representation and may therefore be preferred when reporting magnetization-derived critical current densities.
- 18 November 2026
- Published by IOP Publishing in Superconductor Science and Technology
Open AccessA general unit-invariance theorem for the bean relation: Toward structurally invariant expressions for magnetization-derived critical current density of rectangular parallelepiped samples in perpendicular field
The determination of the critical current density Jc from magnetization hysteresis measurements in superconductors is routinely performed using analytical expressions derived from the Bean critical state model. For rectangular parallelepiped samples in a perpendicular magnetic field, two numerical prefactors, 2 and 20, are commonly reported in the literature. These formulations are often regarded as equivalent representations differing only by unit conventions. However, while the prefactor 2 is universally treated as dimensionless, the prefactor 20 is considered implicitly dimensional or sometimes appears with explicit dimensions. In this paper, we examine the presence of dimensions in this prefactor and discuss the implications associated with the use of the corresponding expression. By proving that only structurally invariant formulations remain unchanged under arbitrary coherent transformations of units, this work provides a rigorous criterion to distinguish universal geometrical expressions from convention-dependent ones. In particular, we establish a general unit-invariance theorem and demonstrate that the prefactor 2, which emerges uniquely from geometrical integration of the critical current distribution, is invariant under arbitrary coherent transformations of units. By contrast, the prefactor 20 which tacitly implies the dimensions [A cm2/emu], and arises within a hybrid CGS electromagnetic framework through the incorporation of specific electromagnetic conversion factors into the geometrical relation, is not invariant under unit transformations. The present discussion addresses invariance at the level of physical quantities, rather than mere numerical equivalence within fixed conventions. Our analysis illustrates how retaining the prefactor 20 outside its native unit framework may introduce systematic numerical deviations when the units of the physical quantities are modified without explicit re-derivation of the coefficient. These deviations do not reflect limitations of the critical state model itself, but rather the convention-dependent nature of hybrid prefactors. We emphasize that calculating the correct value is not a matter of choosing a particular electromagnetic unit system. However, expressions that embed conversion factors within numerical coefficients are inherently unit-dependent and may reduce transparency. For methodological robustness, reproducibility, and reliable comparison of data obtained by different groups and experimental systems, the structurally invariant formulation of the Bean relation provides a more transparent representation and may therefore be preferred when reporting magnetization-derived critical current densities.
- Open Access
- 15 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7089
Numerical Investigation of Electroporation in the Presence of Silica-Coated Magnetic Nanoparticles: Electric Field Perturbation and Transmembrane Voltage Enhancement During Pulse Rise Time
Electroporation outcomes are governed by the local electric field distribution and transmembrane voltage, both of which may be altered by nanoscale elements positioned near the cell membrane. In this study, we developed a two-dimensional finite-element electromagnetic model to investigate the effect of a membrane-proximal silica-coated superparamagnetic iron oxide nanoparticle cluster during a trapezoidal electroporation pulse. The model couples electric and magnetic field components with a membrane electroporation formulation based on Smoluchowski-type pore-density dynamics. Simulations were performed with and without a nanoparticle positioned 5 nm from the membrane, considering different cytosol and extracellular medium conductivities. The results show that the nanoparticle induces a highly localized perturbation of the electric field, whose magnitude depends on the sampling region and conductivity contrast. Transmembrane voltage is modestly and transiently modulated during pulse rise time, whereas the effect is limited during the pulse plateau. Pore-density analysis further indicates that the nanoparticle does not induce a generalized increase in electroporation-related parameters and may locally reduce pore density near the nanoparticle–membrane interface. Overall, the model identifies transient and conductivity-dependent nanoscale field redistribution caused by membrane-proximal silica-coated magnetic nanoparticles, while highlighting the need for three-dimensional modeling and experimental validation before inferring electroporation enhancement.
- 15 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7089
Open AccessNumerical Investigation of Electroporation in the Presence of Silica-Coated Magnetic Nanoparticles: Electric Field Perturbation and Transmembrane Voltage Enhancement During Pulse Rise Time
Electroporation outcomes are governed by the local electric field distribution and transmembrane voltage, both of which may be altered by nanoscale elements positioned near the cell membrane. In this study, we developed a two-dimensional finite-element electromagnetic model to investigate the effect of a membrane-proximal silica-coated superparamagnetic iron oxide nanoparticle cluster during a trapezoidal electroporation pulse. The model couples electric and magnetic field components with a membrane electroporation formulation based on Smoluchowski-type pore-density dynamics. Simulations were performed with and without a nanoparticle positioned 5 nm from the membrane, considering different cytosol and extracellular medium conductivities. The results show that the nanoparticle induces a highly localized perturbation of the electric field, whose magnitude depends on the sampling region and conductivity contrast. Transmembrane voltage is modestly and transiently modulated during pulse rise time, whereas the effect is limited during the pulse plateau. Pore-density analysis further indicates that the nanoparticle does not induce a generalized increase in electroporation-related parameters and may locally reduce pore density near the nanoparticle–membrane interface. Overall, the model identifies transient and conductivity-dependent nanoscale field redistribution caused by membrane-proximal silica-coated magnetic nanoparticles, while highlighting the need for three-dimensional modeling and experimental validation before inferring electroporation enhancement.
- Open Access
- 15 April 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (17)
E-J characterization of YBa 2 Cu 3 O 7-x superconducting thin films with synergetic pinning centers using AC susceptibility techniques
We report a detailed investigation of flux dynamics in YBa₂Cu₃O₇₋ₓ (YBCO) superconducting thin films with strong synergetic pinning centers, using complex AC susceptibility measurements over a wide range of frequencies and DC magnetic fields. A new method is proposed to determine the characteristic pinning energy Uc from the electric field–current density (E–J) characteristics extracted at short time scales from AC susceptibility data. This method overcomes the limitations imposed by the use of standard Arrhenius plots, which rely on assuming a linear temperature dependence (p = 1) of the effective energy barrier U_eff (T,H_dc,J)=U_c (0 K,H_dc )ln(J_c (T,H_dc)/J) (1-T/T_c )^p. Our results provide a more accurate approach for evaluating the magnetic field dependence of Uc, yielding a power-law dependence on the magnetic field induction U_c∝〖B_dc〗^(-0.32), consistent with strong pinning behavior.
- 15 April 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (17)
Open AccessE-J characterization of YBa 2 Cu 3 O 7-x superconducting thin films with synergetic pinning centers using AC susceptibility techniques
We report a detailed investigation of flux dynamics in YBa₂Cu₃O₇₋ₓ (YBCO) superconducting thin films with strong synergetic pinning centers, using complex AC susceptibility measurements over a wide range of frequencies and DC magnetic fields. A new method is proposed to determine the characteristic pinning energy Uc from the electric field–current density (E–J) characteristics extracted at short time scales from AC susceptibility data. This method overcomes the limitations imposed by the use of standard Arrhenius plots, which rely on assuming a linear temperature dependence (p = 1) of the effective energy barrier U_eff (T,H_dc,J)=U_c (0 K,H_dc )ln(J_c (T,H_dc)/J) (1-T/T_c )^p. Our results provide a more accurate approach for evaluating the magnetic field dependence of Uc, yielding a power-law dependence on the magnetic field induction U_c∝〖B_dc〗^(-0.32), consistent with strong pinning behavior.
- Open Access
Anomalous Paramagnetic Meissner-like AC Response in EuRbFe4As4 Superconductor
Magnetic superconductor EuRbFe4As4 is a quite unique system in which macroscopic superconductivity and magnetic ordering coexist, with interesting interactions between Abrikosov vortices and Eu2+ spins that were investigated mostly by static (DC) magnetization measurements. Our aim is to study the dynamic interactions between the two sub-systems using AC susceptibility measurements in a wide range of temperatures and superimposed DC fields. In low DC fields, the magnetic transition at 15 K is clearly visible. We have observed very little difference between the AC susceptibility in different cooling regimes, but large difference for different field orientation. For field perpendicular to the superconducting planes, we have observed an anomalous dependence just below the critical temperature, which is absent in the parallel field orientation. We explained the anomaly by the interplay between the sample dimensions and the temperature dependence of the London penetration depth which may allow the paramagnetic Meissner-like response to be detected in the temperature dependence of the AC susceptibility. We stress that the newly reported phenomenon reflects an AC-susceptibility manifestation of a field-stabilized critical state rather than a thermodynamic phase. In addition, we have observed a paramagnetic AC response in the normal phase, in both field orientations, indicative of interactions between Eu2+ spins and flux lines.
Open AccessAnomalous Paramagnetic Meissner-like AC Response in EuRbFe4As4 Superconductor
Magnetic superconductor EuRbFe4As4 is a quite unique system in which macroscopic superconductivity and magnetic ordering coexist, with interesting interactions between Abrikosov vortices and Eu2+ spins that were investigated mostly by static (DC) magnetization measurements. Our aim is to study the dynamic interactions between the two sub-systems using AC susceptibility measurements in a wide range of temperatures and superimposed DC fields. In low DC fields, the magnetic transition at 15 K is clearly visible. We have observed very little difference between the AC susceptibility in different cooling regimes, but large difference for different field orientation. For field perpendicular to the superconducting planes, we have observed an anomalous dependence just below the critical temperature, which is absent in the parallel field orientation. We explained the anomaly by the interplay between the sample dimensions and the temperature dependence of the London penetration depth which may allow the paramagnetic Meissner-like response to be detected in the temperature dependence of the AC susceptibility. We stress that the newly reported phenomenon reflects an AC-susceptibility manifestation of a field-stabilized critical state rather than a thermodynamic phase. In addition, we have observed a paramagnetic AC response in the normal phase, in both field orientations, indicative of interactions between Eu2+ spins and flux lines.
- Open Access
Limit to Self-Field Critical Current Density in Thin-Film, Type-II Superconductors
In the last decade, the self-field critical current density Jc(s.f.) in Type-II superconductors has been considered fundamentally limited by a Silsbee-like criterion of Jc(s.f.) = Hc1/λ. We show that this universal limit to self-field critical current density Jc(s.f.) is not universally valid. We present several examples for this in YBa2Cu3O7−δ-type and REBa2Cu3O7−δ thin films and one for Nb thin films and show that calculated Jc(s.f.) using the Silsbee-like criterion using thermodynamic parameters has been substantially exceeded experimentally. We also show that Jc(s.f.) can be significantly improved by incorporation of artificial pinning centers (APCs), further implying that no such universal limit to Jc(s.f.) can exist because such an upper bound, Jc(s.f.) would have to be independent of APCs. These findings call for a revision of the accepted understanding of current-carrying limits in Type-II superconductors and reveal substantial potential for improving Jc in REBCO-based coated conductors through optimization of APCs for large-scale applications, including commercial nuclear fusion.
Open AccessLimit to Self-Field Critical Current Density in Thin-Film, Type-II Superconductors
In the last decade, the self-field critical current density Jc(s.f.) in Type-II superconductors has been considered fundamentally limited by a Silsbee-like criterion of Jc(s.f.) = Hc1/λ. We show that this universal limit to self-field critical current density Jc(s.f.) is not universally valid. We present several examples for this in YBa2Cu3O7−δ-type and REBa2Cu3O7−δ thin films and one for Nb thin films and show that calculated Jc(s.f.) using the Silsbee-like criterion using thermodynamic parameters has been substantially exceeded experimentally. We also show that Jc(s.f.) can be significantly improved by incorporation of artificial pinning centers (APCs), further implying that no such universal limit to Jc(s.f.) can exist because such an upper bound, Jc(s.f.) would have to be independent of APCs. These findings call for a revision of the accepted understanding of current-carrying limits in Type-II superconductors and reveal substantial potential for improving Jc in REBCO-based coated conductors through optimization of APCs for large-scale applications, including commercial nuclear fusion.
- Open Access
- 1 February 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2) , 023502
Roadmap on nanoscale superconductivity for quantum technologies
In 2025, the Year of Quantum Science and Technology ( https://quantum2025.org/ ), we celebrate a century of quantum mechanics, witnessing a surge in activities that illuminate its inherent strangeness and drive technological innovation. Superconductivity, discovered 114 years ago, stands as a prime example, offering direct and compelling evidence of macroscopic quantum phenomena. Beyond its ability to conduct immense currents without loss, superconductivity reveals the quantum realm operating on a scale we can directly observe and manipulate. The macroscopic quantum coherence, where an ensemble of particles is described by a single wave function, leads to remarkable consequences: dissipation-less current and flux quantization—the basic properties exploited in superconducting quantum circuit fabrication. This Roadmap has been inspired by intensive discussions and collaborations emerging from the European Cooperation in Science & Technology COST-Action CA21144 (SuperQuMap—Superconducting Nanodevices and Quantum Materials for Coherent Manipulation). The aim of the COST Action SuperQuMap is to establish a strong European network centered on macroscopic quantum behavior in superconductors, bringing together groups of different backgrounds and more than 30 countries. The roadmap outlines the network’s concrete activities, driving advancements in superconductor-based quantum technologies and charting future directions. Spanning fundamental research to practical applications, the roadmap incorporates insights from industry partners developing quantum computation. It begins by exploring quantum materials, highlighting how topology and electronic correlations could catalyze a quantum leap in technology. We then delve into manipulating the superconducting phase, leveraging advancements in magnetism, 3D fabrication, and tunable correlations. Further, we showcase the advanced microscopy techniques—such as angle-resolved photoemission spectroscopy and scanning probes—used to visualize quantum behavior. Finally, and crucially, we detail the quantum devices developed within the network, and their transformative impact on modern quantum computing approaches.
- 1 February 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2) , 023502
Open AccessRoadmap on nanoscale superconductivity for quantum technologies
In 2025, the Year of Quantum Science and Technology ( https://quantum2025.org/ ), we celebrate a century of quantum mechanics, witnessing a surge in activities that illuminate its inherent strangeness and drive technological innovation. Superconductivity, discovered 114 years ago, stands as a prime example, offering direct and compelling evidence of macroscopic quantum phenomena. Beyond its ability to conduct immense currents without loss, superconductivity reveals the quantum realm operating on a scale we can directly observe and manipulate. The macroscopic quantum coherence, where an ensemble of particles is described by a single wave function, leads to remarkable consequences: dissipation-less current and flux quantization—the basic properties exploited in superconducting quantum circuit fabrication. This Roadmap has been inspired by intensive discussions and collaborations emerging from the European Cooperation in Science & Technology COST-Action CA21144 (SuperQuMap—Superconducting Nanodevices and Quantum Materials for Coherent Manipulation). The aim of the COST Action SuperQuMap is to establish a strong European network centered on macroscopic quantum behavior in superconductors, bringing together groups of different backgrounds and more than 30 countries. The roadmap outlines the network’s concrete activities, driving advancements in superconductor-based quantum technologies and charting future directions. Spanning fundamental research to practical applications, the roadmap incorporates insights from industry partners developing quantum computation. It begins by exploring quantum materials, highlighting how topology and electronic correlations could catalyze a quantum leap in technology. We then delve into manipulating the superconducting phase, leveraging advancements in magnetism, 3D fabrication, and tunable correlations. Further, we showcase the advanced microscopy techniques—such as angle-resolved photoemission spectroscopy and scanning probes—used to visualize quantum behavior. Finally, and crucially, we detail the quantum devices developed within the network, and their transformative impact on modern quantum computing approaches.
- Open Access
Advances in Cuprates and Iron-Based Superconductors: Physics, Properties, and Applications
The study of cuprates and iron-based superconductors continues to evolve rapidly, driven by the quest to understand unconventional pairing mechanisms and to harness their remarkable properties for high-field applications
Open AccessAdvances in Cuprates and Iron-Based Superconductors: Physics, Properties, and Applications
The study of cuprates and iron-based superconductors continues to evolve rapidly, driven by the quest to understand unconventional pairing mechanisms and to harness their remarkable properties for high-field applications
- Open Access
- 3 December 2025
- Published by MDPI AG in Preprints.org
Anomalous AC Susceptibility Response and Paramagnetic Meissner Phase of EuRbFe4As4 Superconductor
Magnetic superconductor EuRbFe4As4 is a quite unique system in which macroscopic superconductivity and magnetic ordering coexist, with interesting interactions between Abrikosov vortices and Eu2+ spins that were investigated mostly by static (DC) magnetization measurements. Our aim is to study the dynamic interactions between the two sub-systems using AC susceptibility measurements in a wide range of temperatures and superimposed DC fields. In low DC fields, the magnetic transition at 15 K is clearly visible. We have observed very little difference between the AC susceptibility in different cooling regimes, but large difference for different field orientation. For field perpendicular to the superconducting planes, we have observed an anomalous dependence just below the critical temperature, which is absent in the parallel field orientation. We explained the anomaly by the interplay between the sample dimensions and the temperature dependence of the London penetration depth which may allow the paramagnetic Meissner phase to be detected in the susceptibility response.
- 3 December 2025
- Published by MDPI AG in Preprints.org
Open AccessAnomalous AC Susceptibility Response and Paramagnetic Meissner Phase of EuRbFe4As4 Superconductor
Magnetic superconductor EuRbFe4As4 is a quite unique system in which macroscopic superconductivity and magnetic ordering coexist, with interesting interactions between Abrikosov vortices and Eu2+ spins that were investigated mostly by static (DC) magnetization measurements. Our aim is to study the dynamic interactions between the two sub-systems using AC susceptibility measurements in a wide range of temperatures and superimposed DC fields. In low DC fields, the magnetic transition at 15 K is clearly visible. We have observed very little difference between the AC susceptibility in different cooling regimes, but large difference for different field orientation. For field perpendicular to the superconducting planes, we have observed an anomalous dependence just below the critical temperature, which is absent in the parallel field orientation. We explained the anomaly by the interplay between the sample dimensions and the temperature dependence of the London penetration depth which may allow the paramagnetic Meissner phase to be detected in the susceptibility response.
- Open Access
- 5 August 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (15) , 1196
The Effect of Copper Adsorption on Iron Oxide Magnetic Nanoparticles Embedded in a Sodium Alginate Bead
The preparation and use of iron oxide magnetic nanoparticles for water remediation is a widely investigated research field. To improve the efficacy of such nanomaterials, different synthetic processes and functionalization methods have been developed in the framework of green chemistry to exploit their magnetic properties and adsorption capacity in a sustainable way. In this work, iron oxide magnetic nanoparticles embedded in cross-linked sodium alginate beads designed to clean water from metal ions were magnetically characterized. In particular, the effect of copper adsorption on their magnetic properties was investigated. The magnetic characterization in a DC field of the beads before adsorption showed the presence of a superparamagnetic state at 300 K—a state that was also preserved after copper adsorption. The main differences in terms of magnetic properties before and after Cu2+ adsorption were the reduction of the magnetic signal (observed by comparing the saturation magnetization) and a different shape of the blocking temperature distribution obtained by magnetization versus temperature measurements. The evaluation of the reduction in magnetization can be important from the application perspective since it can affect the efficiency of the beads’ removal from the water medium after treatment.
- 5 August 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (15) , 1196
Open AccessThe Effect of Copper Adsorption on Iron Oxide Magnetic Nanoparticles Embedded in a Sodium Alginate Bead
The preparation and use of iron oxide magnetic nanoparticles for water remediation is a widely investigated research field. To improve the efficacy of such nanomaterials, different synthetic processes and functionalization methods have been developed in the framework of green chemistry to exploit their magnetic properties and adsorption capacity in a sustainable way. In this work, iron oxide magnetic nanoparticles embedded in cross-linked sodium alginate beads designed to clean water from metal ions were magnetically characterized. In particular, the effect of copper adsorption on their magnetic properties was investigated. The magnetic characterization in a DC field of the beads before adsorption showed the presence of a superparamagnetic state at 300 K—a state that was also preserved after copper adsorption. The main differences in terms of magnetic properties before and after Cu2+ adsorption were the reduction of the magnetic signal (observed by comparing the saturation magnetization) and a different shape of the blocking temperature distribution obtained by magnetization versus temperature measurements. The evaluation of the reduction in magnetization can be important from the application perspective since it can affect the efficiency of the beads’ removal from the water medium after treatment.
- Open Access
- 26 May 2025
- Published by Elsevier in Progress in Materials Science
- Vol. 155
Critical current density in advanced superconductors
- 26 May 2025
- Published by Elsevier in Progress in Materials Science
- Vol. 155
Open AccessCritical current density in advanced superconductors