Abolfazl Bijari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Abolfazl Bijari has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Salman Zandian
Faculty of Electrical and Computer Engineering, University of Birjand, Birjand, Iran
3 shared publicationsMehrdad Harifi-Mood
Faculty of Electrical and Computer Engineering, INRS (EMT), University of Quebec, Québec City, Canada
2 shared publications- Mohamad Eshghi
Faculty of Electrical and Computer Engineering, University of Birjand, Birjand, Iran
2 shared publications - Mohammad Amin Mallaki
Department of Electrical and Computer Engineering University of Birjand Birjand Iran
2 shared publications Mohammadjavad Ebrahimipour
Department of Electronics, Information and Bioengineering Politecnico di Milano, Milan, Italy
2 shared publications- Nasser Mehrshad
University of Birjand
2 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Springer Nature in Scientific Reports
A compact dual-mode single-resonator DGS microwave sensor for self-referenced permittivity characterization
This paper presents a compact microwave sensor for permittivity characterization based on a single defected ground structure (DGS) resonator with an intrinsic dual-mode response. Unlike conventional differential sensors that require two physically separated resonators, the proposed design exploits two resonant modes intrinsically generated by a stub-loaded double split-ring resonator to enable internal referencing within a single compact structure, thereby eliminating inter-resonator mismatch issues and reducing the sensor footprint. The lower-frequency mode exhibits weaker interaction with the sample under test than the sensing mode and acts as a common-mode reference, whereas the higher-frequency mode shows strong electric-field confinement in the sensing region and is used for permittivity sensing. A prototype was fabricated on a Rogers RO4003 substrate and experimentally validated using several solid dielectric samples. The measured results show a normalized sensitivity of 1.41% and a coefficient of determination of R 2 = 0.9814, in good agreement with full-wave simulations. Owing to its compact size, single-resonator implementation, and self-referenced operation, the proposed sensor is suitable for non-destructive dielectric characterization.
- 15 October 2026
- Published by Springer Nature in Scientific Reports
Open AccessA compact dual-mode single-resonator DGS microwave sensor for self-referenced permittivity characterization
This paper presents a compact microwave sensor for permittivity characterization based on a single defected ground structure (DGS) resonator with an intrinsic dual-mode response. Unlike conventional differential sensors that require two physically separated resonators, the proposed design exploits two resonant modes intrinsically generated by a stub-loaded double split-ring resonator to enable internal referencing within a single compact structure, thereby eliminating inter-resonator mismatch issues and reducing the sensor footprint. The lower-frequency mode exhibits weaker interaction with the sample under test than the sensing mode and acts as a common-mode reference, whereas the higher-frequency mode shows strong electric-field confinement in the sensing region and is used for permittivity sensing. A prototype was fabricated on a Rogers RO4003 substrate and experimentally validated using several solid dielectric samples. The measured results show a normalized sensitivity of 1.41% and a coefficient of determination of R 2 = 0.9814, in good agreement with full-wave simulations. Owing to its compact size, single-resonator implementation, and self-referenced operation, the proposed sensor is suitable for non-destructive dielectric characterization.
- 30 December 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (2) , 025103
Highly sensitive differential moisture sensor based on a novel multi-mode resonator
This paper presents a highly sensitive differential microwave sensor for moisture content (MC) measurement, demonstrated using whole-wheat flour as the sample under test. The proposed design incorporates a pair of novel symmetrical multi-mode resonators placed on either side of a 50 Ω microstrip transmission line. Fabricated on a low-cost FR-4 substrate, the sensor offers an optimal balance between high sensitivity and economic feasibility. Differential sensing is realized by employing one resonator as a reference ( έ r = 1) and the other as the sensing element exposed to the sample. The sensor is designed to generate four transmission zeros (TZs) within the frequency range of 0.1–4 GHz, with individual sensitivity of each TZ analyzed and compared. The fourth mode demonstrates a peak sensitivity of 168.8 MHz/ έ r . The sensor’s operational mechanism is examined through odd- and even-mode analysis, validated via full-wave electromagnetic simulations using CST Studio Suite. The fabricated prototype has compact physical dimensions of 8.4 × 4 × 0.16 cm 3 . Experimental verification was performed using both a vector network analyzer and a custom low-cost readout circuit, with results showing excellent agreement. The proposed sensor’s compact size, low cost, and high-performance position it as a strong candidate for precision MC monitoring in food industry applications.
- 30 December 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 37 (2) , 025103
Highly sensitive differential moisture sensor based on a novel multi-mode resonator
This paper presents a highly sensitive differential microwave sensor for moisture content (MC) measurement, demonstrated using whole-wheat flour as the sample under test. The proposed design incorporates a pair of novel symmetrical multi-mode resonators placed on either side of a 50 Ω microstrip transmission line. Fabricated on a low-cost FR-4 substrate, the sensor offers an optimal balance between high sensitivity and economic feasibility. Differential sensing is realized by employing one resonator as a reference ( έ r = 1) and the other as the sensing element exposed to the sample. The sensor is designed to generate four transmission zeros (TZs) within the frequency range of 0.1–4 GHz, with individual sensitivity of each TZ analyzed and compared. The fourth mode demonstrates a peak sensitivity of 168.8 MHz/ έ r . The sensor’s operational mechanism is examined through odd- and even-mode analysis, validated via full-wave electromagnetic simulations using CST Studio Suite. The fabricated prototype has compact physical dimensions of 8.4 × 4 × 0.16 cm 3 . Experimental verification was performed using both a vector network analyzer and a custom low-cost readout circuit, with results showing excellent agreement. The proposed sensor’s compact size, low cost, and high-performance position it as a strong candidate for precision MC monitoring in food industry applications.
- Open Access
- 1 August 2025
- Published by Universitas Ahmad Dahlan in TELKOMNIKA (Telecommunication Computing Electronics and Control)
- Vol. 23 (4) , 1046-1057
A new resonant-based sensor for non-invasive measurement of blood glucose levels
A new resonant-based sensor for non-invasive measurement of blood glucose levels
- 1 August 2025
- Published by Universitas Ahmad Dahlan in TELKOMNIKA (Telecommunication Computing Electronics and Control)
- Vol. 23 (4) , 1046-1057
Open AccessA new resonant-based sensor for non-invasive measurement of blood glucose levels
A new resonant-based sensor for non-invasive measurement of blood glucose levels
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (8) , 13210-13218
Angular Displacement Sensor Based on Double-Ring Resonator With a Novel Readout Circuit
This paper presents an angular displacement sensor utilizing a double ring resonator (DRR) and introduces an integrable and low-cost readout circuit to detect the transmission zero position in the sensor’s frequency response. The proposed sensor comprises a DRR-based stator and an open-ended stub rotor. The interaction between the rotor and stator via ohmic contact causes a notable change in the effective electrical length of the stator, leading to a measurable shift in the position of the transmission zero. The theoretical analysis of the sensor is conducted using ABCD matrices, ensuring accurate modeling and characterization. A novel readout circuit is implemented by a frequency synthesizer and a power detector. The proposed circuit effectively detects notches or peaks in the frequency response of the device under test (DUT) by applying a precisely controlled sinusoidal signal and measuring the output power. This enables reliable detection over a wide frequency range of 35 MHz to 4.4 GHz. The proposed readout circuit supports real-time measurements for resonant-based sensors in industrial applications, eliminating the need for expensive laboratory equipment. The experimental results show good agreement between the measurements from the readout circuit and those from a vector network analyzer (VNA), confirming the reliability and accuracy of the proposed method.
- 5 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (8) , 13210-13218
Angular Displacement Sensor Based on Double-Ring Resonator With a Novel Readout Circuit
This paper presents an angular displacement sensor utilizing a double ring resonator (DRR) and introduces an integrable and low-cost readout circuit to detect the transmission zero position in the sensor’s frequency response. The proposed sensor comprises a DRR-based stator and an open-ended stub rotor. The interaction between the rotor and stator via ohmic contact causes a notable change in the effective electrical length of the stator, leading to a measurable shift in the position of the transmission zero. The theoretical analysis of the sensor is conducted using ABCD matrices, ensuring accurate modeling and characterization. A novel readout circuit is implemented by a frequency synthesizer and a power detector. The proposed circuit effectively detects notches or peaks in the frequency response of the device under test (DUT) by applying a precisely controlled sinusoidal signal and measuring the output power. This enables reliable detection over a wide frequency range of 35 MHz to 4.4 GHz. The proposed readout circuit supports real-time measurements for resonant-based sensors in industrial applications, eliminating the need for expensive laboratory equipment. The experimental results show good agreement between the measurements from the readout circuit and those from a vector network analyzer (VNA), confirming the reliability and accuracy of the proposed method.
- 21 October 2024
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 53 (7) , 3849-3862
An Inductor‐Less Zero‐IF Down‐Conversion Mixer With Low Flicker Noise and High Conversion Gain
This paper presents a novel active inductor (AI) to improve the performance of a down‐conversion active mixer in terms of conversion gain (CG) and flicker noise. The proposed AI exhibits negative resistance and partially flat inductance over a wide frequency band of 0.5–4.5 GHz. The effect of inserting the AI between the source of the switching quad of a Gilbert cell mixer is theoretically analyzed. The proposed inductor‐less mixer, designed to operate at a 2.4‐GHz RF input frequency and a 10‐MHz IF output frequency, employs current reuse and self‐forward body bias (SFBB) techniques. The proposed circuit is simulated in Cadence Spectre‐RF using RF‐TSMC 0.18‐μm CMOS technology. Post‐layout simulations demonstrate that the proposed AI significantly reduces flicker noise by over 23 dB at an IF output frequency of 1 kHz and improves the CG by over 16 dB at an RF frequency of 2.4 GHz. The proposed mixer achieves a CG of 37.6 dB and a flicker noise corner frequency of 6 kHz. Additionally, it exhibits a third‐order intermodulation intercept point (IIP3) of −5.2 dBm and a double‐sideband noise figure (DSB‐NF) of 6.1 dB at the IF output frequency of 10 MHz. Operating with a 1.5‐V supply, the proposed mixer consumes 10.6 mW of power.
- 21 October 2024
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 53 (7) , 3849-3862
An Inductor‐Less Zero‐IF Down‐Conversion Mixer With Low Flicker Noise and High Conversion Gain
This paper presents a novel active inductor (AI) to improve the performance of a down‐conversion active mixer in terms of conversion gain (CG) and flicker noise. The proposed AI exhibits negative resistance and partially flat inductance over a wide frequency band of 0.5–4.5 GHz. The effect of inserting the AI between the source of the switching quad of a Gilbert cell mixer is theoretically analyzed. The proposed inductor‐less mixer, designed to operate at a 2.4‐GHz RF input frequency and a 10‐MHz IF output frequency, employs current reuse and self‐forward body bias (SFBB) techniques. The proposed circuit is simulated in Cadence Spectre‐RF using RF‐TSMC 0.18‐μm CMOS technology. Post‐layout simulations demonstrate that the proposed AI significantly reduces flicker noise by over 23 dB at an IF output frequency of 1 kHz and improves the CG by over 16 dB at an RF frequency of 2.4 GHz. The proposed mixer achieves a CG of 37.6 dB and a flicker noise corner frequency of 6 kHz. Additionally, it exhibits a third‐order intermodulation intercept point (IIP3) of −5.2 dBm and a double‐sideband noise figure (DSB‐NF) of 6.1 dB at the IF output frequency of 10 MHz. Operating with a 1.5‐V supply, the proposed mixer consumes 10.6 mW of power.
- 16 June 2024
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 53 (2) , 571-594
An ultra‐low‐power low‐noise amplifier using a combination of current reuse and self‐forward body bias techniques for biomedical applications
Summary: Low‐power low noise amplifiers (LNAs) are critical block in the radio frequency (RF) front‐end of medical device radiocommunications service (MedRadio) receivers for amplifying weak received signals while introducing minimal noise. Despite the inherently low transconductance of MOS transistors, it is possible to achieve low noise, high gain, and good linearity in low power LNAs. This paper presents a combination of techniques to realize an ultra‐low‐power LNA with a compact size and high performance. The proposed LNA utilizes multiple gm‐boosting and self‐forward body bias techniques, with certain transistors operating in weak inversion. Additionally, the Multi‐Objective Inclined Planes System Optimization algorithm is employed to determine the optimal values of the circuit components, thereby achieving the best compromise among the various performance parameters. The proposed LNA with buffer is designed and simulated using an 180 nm CMOS process over the frequency band of 0.3–1 GHz. Simulated results show that the proposed LNA achieves a gain of 19.6 dB, a noise figure of 5.1 dB, good input matching (S11 < −10 dB), and a third‐order intermodulation intercept point (IIP3) of 3.8 dBm. Additionally, it consumes 320 μW (without buffer) from a 1 V power supply, and the chip area is 235 μm × 372 μm. The simulated results demonstrate that the proposed ultra‐low power LNA is a promising candidate for biomedical applications.
- 16 June 2024
- Published by Wiley in International Journal of Circuit Theory and Applications
- Vol. 53 (2) , 571-594
An ultra‐low‐power low‐noise amplifier using a combination of current reuse and self‐forward body bias techniques for biomedical applications
Summary: Low‐power low noise amplifiers (LNAs) are critical block in the radio frequency (RF) front‐end of medical device radiocommunications service (MedRadio) receivers for amplifying weak received signals while introducing minimal noise. Despite the inherently low transconductance of MOS transistors, it is possible to achieve low noise, high gain, and good linearity in low power LNAs. This paper presents a combination of techniques to realize an ultra‐low‐power LNA with a compact size and high performance. The proposed LNA utilizes multiple gm‐boosting and self‐forward body bias techniques, with certain transistors operating in weak inversion. Additionally, the Multi‐Objective Inclined Planes System Optimization algorithm is employed to determine the optimal values of the circuit components, thereby achieving the best compromise among the various performance parameters. The proposed LNA with buffer is designed and simulated using an 180 nm CMOS process over the frequency band of 0.3–1 GHz. Simulated results show that the proposed LNA achieves a gain of 19.6 dB, a noise figure of 5.1 dB, good input matching (S11 < −10 dB), and a third‐order intermodulation intercept point (IIP3) of 3.8 dBm. Additionally, it consumes 320 μW (without buffer) from a 1 V power supply, and the chip area is 235 μm × 372 μm. The simulated results demonstrate that the proposed ultra‐low power LNA is a promising candidate for biomedical applications.
- 17 November 2023
- Published by Springer Nature in Neural Computing and Applications
- Vol. 36 (4) , 1833-1847
A new approach to multi-objective optimization of a tapered matrix distributed amplifier for UWB applications
- 17 November 2023
- Published by Springer Nature in Neural Computing and Applications
- Vol. 36 (4) , 1833-1847
A new approach to multi-objective optimization of a tapered matrix distributed amplifier for UWB applications
- 14 October 2022
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (12)
A new compact, wide bandwidthdual‐passbandmicrostrip filter based ondual‐mode stepped‐impedance‐resonators
- 14 October 2022
- Published by Wiley in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 32 (12)
A new compact, wide bandwidthdual‐passbandmicrostrip filter based ondual‐mode stepped‐impedance‐resonators
- 12 May 2022
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (12) , 8554-8560
A Compact Dual-Band Bandpass Filter Using Coupled Microstrip Lines
In this paper, a new compact dual-band bandpass filter (DB-BPF) is proposed using parallel coupled lines. The design method is based on introducing transmission zeros (TZs) in the frequency response of a single-wideband filter. In the proposed structure, three coupled lines and a multi-mode resonator are used to realize the wide bandpass filter. Meanwhile, two coupled lines that are connected at the end and loaded by an open-circuit stub are employed to make a new notch filter. The proposed DB-BPF is designed and fabricated on Rogers RO3210 substrate for Wireless Local Area Networks (WLANs) applications. The simulation results show good agreement with measurements. The measured results exhibit two passbands centered at 2.4 and 5.2 GHz, having an insertion loss of less than 0.1 dB and 0.9 dB, respectively. Low insertion loss, compact size, and high attenuation between two passbands are the main advantages of the proposed DB-BPF.
- 12 May 2022
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (12) , 8554-8560
A Compact Dual-Band Bandpass Filter Using Coupled Microstrip Lines
In this paper, a new compact dual-band bandpass filter (DB-BPF) is proposed using parallel coupled lines. The design method is based on introducing transmission zeros (TZs) in the frequency response of a single-wideband filter. In the proposed structure, three coupled lines and a multi-mode resonator are used to realize the wide bandpass filter. Meanwhile, two coupled lines that are connected at the end and loaded by an open-circuit stub are employed to make a new notch filter. The proposed DB-BPF is designed and fabricated on Rogers RO3210 substrate for Wireless Local Area Networks (WLANs) applications. The simulation results show good agreement with measurements. The measured results exhibit two passbands centered at 2.4 and 5.2 GHz, having an insertion loss of less than 0.1 dB and 0.9 dB, respectively. Low insertion loss, compact size, and high attenuation between two passbands are the main advantages of the proposed DB-BPF.
- 17 February 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 107 (3) , 551-565
Power efficiency enhancement analysis of an inverse class D power amplifier for NB-IoT applications
- 17 February 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 107 (3) , 551-565
Power efficiency enhancement analysis of an inverse class D power amplifier for NB-IoT applications