Miron Victor Landau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Miron Victor Landau has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Mordechay Herskowitz
Chemical Engineering Department, Blechner Center for Industrial Catalysis and Process Development, Ben-Gurion University of the Negev, Beer-Sheva, Israel
19 shared publications David Fuks
3 shared publicationsRoxana Vidruk
3 shared publications- Anthon S. Ivanov
Department of Chemistry, M. V. Lomonosov Moscow State University, Leninskie Gory 1, Bld. 3, Moscow 119991, Russia
2 shared publications Dmitro Vingurt
2 shared publications- Eran Edri
Ben-Gurion University of the Negev
2 shared publications
Latest Publications
- Open Access
- 8 June 2023
- Published by American Chemical Society (ACS) in ACS Engineering Au
- Vol. 3 (4) , 265-277
Selective Partial Oxidation of Methane with CO2 Using Mobile Lattice Oxygens of LSF
- 8 June 2023
- Published by American Chemical Society (ACS) in ACS Engineering Au
- Vol. 3 (4) , 265-277
Open AccessSelective Partial Oxidation of Methane with CO2 Using Mobile Lattice Oxygens of LSF
- 6 January 2022
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (29) , 10387-10399
Hydrogenation of CO2 on Fe-Based Catalysts: Preferred Route to Renewable Liquid Fuels
- 6 January 2022
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (29) , 10387-10399
Hydrogenation of CO2 on Fe-Based Catalysts: Preferred Route to Renewable Liquid Fuels
- Open Access
Core-Shell Fe2O3@La1−xSrxFeO3−δ Material for Catalytic Oxidations: Coverage of Iron Oxide Core, Oxygen Storage Capacity and Reactivity of Surface Oxygens
A series of Fe2O3@LSF (La0.8Sr0.2FeO3−δ perovskite) core-shell materials (CSM) was prepared by infiltration of LSF precursors gel containing various complexants and their mixtures to nanocrystalline aggregates of hematite followed by thermal treatment. The content of LSF phase and amount of carboxyl groups in complexant determine the percent coverage of iron oxide core with the LSF shell. The most conformal coating core-shell material was prepared with citric acid as the complexant, contained 60 wt% LSF with 98% core coverage. The morphology of the CSM was studied by HRTEM-EELS combined with SEM-FIB for particles cross-sections. The reactivity of surface oxygen species and their amounts were determined by H2-TPR, TGA-DTG, the oxidation state of surface oxygen ions by XPS. It was found that at complete core coverage with perovskite shell, the distribution of surface oxygen species according to redox reactivity in CSM resemble pure LSF, but its lattice oxygen storage capacity is 2–2.5 times higher. At partial coverage, the distribution of surface oxygen species according to redox reactivity resembles that in iron oxide.
Open AccessCore-Shell Fe2O3@La1−xSrxFeO3−δ Material for Catalytic Oxidations: Coverage of Iron Oxide Core, Oxygen Storage Capacity and Reactivity of Surface Oxygens
A series of Fe2O3@LSF (La0.8Sr0.2FeO3−δ perovskite) core-shell materials (CSM) was prepared by infiltration of LSF precursors gel containing various complexants and their mixtures to nanocrystalline aggregates of hematite followed by thermal treatment. The content of LSF phase and amount of carboxyl groups in complexant determine the percent coverage of iron oxide core with the LSF shell. The most conformal coating core-shell material was prepared with citric acid as the complexant, contained 60 wt% LSF with 98% core coverage. The morphology of the CSM was studied by HRTEM-EELS combined with SEM-FIB for particles cross-sections. The reactivity of surface oxygen species and their amounts were determined by H2-TPR, TGA-DTG, the oxidation state of surface oxygen ions by XPS. It was found that at complete core coverage with perovskite shell, the distribution of surface oxygen species according to redox reactivity in CSM resemble pure LSF, but its lattice oxygen storage capacity is 2–2.5 times higher. At partial coverage, the distribution of surface oxygen species according to redox reactivity resembles that in iron oxide.
- 24 September 2021
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 11 (22) , 7368-7379
Al-Doped magnetite encapsulated in mesoporous carbon: a long-lasting Fenton catalyst for CWPO of phenol in a fixed-bed reactor under mild conditions
Al substituted magnetite was identified as a promising heterogeneous Fenton catalyst for CWPO of 200 ppm phenol in a continuous system under mild conditions (pH 5, 40 °C, 0.1 ml min−1, 1.2S H2O2) for 500 h with 80% TOC conversion, 1 ppm Fe leaching.
- 24 September 2021
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 11 (22) , 7368-7379
Al-Doped magnetite encapsulated in mesoporous carbon: a long-lasting Fenton catalyst for CWPO of phenol in a fixed-bed reactor under mild conditions
Al substituted magnetite was identified as a promising heterogeneous Fenton catalyst for CWPO of 200 ppm phenol in a continuous system under mild conditions (pH 5, 40 °C, 0.1 ml min−1, 1.2S H2O2) for 500 h with 80% TOC conversion, 1 ppm Fe leaching.
- Open Access
Eco-Friendly and Sustainable Process for Converting Hydrous Bioethanol to Butanol
The purpose of the study was the development of water-resistant catalyst and catalytic processes for the conversion of hydrous ethanol to 1-butanol. Water, in hydrous ethanol, strongly inhibits conversion to 1-butanol on solid catalysts. In this study, the nonstoichiometric P-deficient hydroxyapatite containing carbonate anions (C-HAP), Ca10−x/2(PO4)6−x(CO3)x(OH)2, displayed good performance in the Guerbet condensation of hydrated ethanol to 1-butanol, after proper stabilization of reaction conditions. Hydrous ethanol (96 wt%) was converted on C-HAP formed as extrudates with silica binder at 400 °C and weight hour space velocity (WHSV) = 0.5–1.0 h−1 to yield 21–23% 1-butanol and 73–74% selectivity. It displayed stable operation for up to 170 h on streams conducted in bench and mini-pilot rigs with catalyst loadings of 2 and 50 cm3, respectively. The process simulation employed the recycling of ethanol without laboratory verification to reach 68% theoretical yield of 1-butanol. The techno-economic analysis demonstrated the feasibility of this process, showing that it may be profitable depending on the prices of hydrated ethanol and 1-butanol.
Open AccessEco-Friendly and Sustainable Process for Converting Hydrous Bioethanol to Butanol
The purpose of the study was the development of water-resistant catalyst and catalytic processes for the conversion of hydrous ethanol to 1-butanol. Water, in hydrous ethanol, strongly inhibits conversion to 1-butanol on solid catalysts. In this study, the nonstoichiometric P-deficient hydroxyapatite containing carbonate anions (C-HAP), Ca10−x/2(PO4)6−x(CO3)x(OH)2, displayed good performance in the Guerbet condensation of hydrated ethanol to 1-butanol, after proper stabilization of reaction conditions. Hydrous ethanol (96 wt%) was converted on C-HAP formed as extrudates with silica binder at 400 °C and weight hour space velocity (WHSV) = 0.5–1.0 h−1 to yield 21–23% 1-butanol and 73–74% selectivity. It displayed stable operation for up to 170 h on streams conducted in bench and mini-pilot rigs with catalyst loadings of 2 and 50 cm3, respectively. The process simulation employed the recycling of ethanol without laboratory verification to reach 68% theoretical yield of 1-butanol. The techno-economic analysis demonstrated the feasibility of this process, showing that it may be profitable depending on the prices of hydrated ethanol and 1-butanol.
- 23 November 2020
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 5 (2) , 486-500
Techno-economic analysis of a sustainable process for converting CO 2 and H 2 O to feedstock for fuels and chemicals
Environmental and economically-competitive co-electrolysis and catalytic processes were developed for production of feedstock for fuels and chemicals from CO 2 and H 2 O.
- 23 November 2020
- Published by Royal Society of Chemistry (RSC) in Sustainable Energy & Fuels
- Vol. 5 (2) , 486-500
Techno-economic analysis of a sustainable process for converting CO 2 and H 2 O to feedstock for fuels and chemicals
Environmental and economically-competitive co-electrolysis and catalytic processes were developed for production of feedstock for fuels and chemicals from CO 2 and H 2 O.
- Open Access
Reverse Water Gas Shift by Chemical Looping with Iron-Substituted Hexaaluminate Catalysts
The Fe-substituted Ba-hexaaluminates (BaFeHAl) are active catalysts for reverse water-gas shift (RWGS) reaction conducted in chemical looping mode. Increasing of the degree of substitution of Al3+ for Fe3+ ions in co-precipitated BaHAl from 60% (BaFeHAl) to 100% (BaFe-hexaferrite, BaFeHF), growing its surface area from 5 to 30 m2/g, and promotion with potassium increased the CO capacity in isothermal RWGS-CL runs at 350–450 °C, where the hexaaluminate/hexaferrite structure is stable. Increasing H2-reduction temperature converts BaFeHAl to a thermally stable BaFeHF modification that contains additional Ba-O-Fe bridges in its structure, reinforcing the connection between alternatively stacked spinel blocks. This material displayed the highest CO capacity of 400 µmol/g at isothermal RWGS-CL run conducted at 550 °C due to increased concentration of oxygen vacancies reflected by greater surface Fe2+/Fe3+ ratio detected by XPS. The results demonstrate direct connection between CO capacity measured in RWGS-CL experiments and calculated CO2 conversion.
Open AccessReverse Water Gas Shift by Chemical Looping with Iron-Substituted Hexaaluminate Catalysts
The Fe-substituted Ba-hexaaluminates (BaFeHAl) are active catalysts for reverse water-gas shift (RWGS) reaction conducted in chemical looping mode. Increasing of the degree of substitution of Al3+ for Fe3+ ions in co-precipitated BaHAl from 60% (BaFeHAl) to 100% (BaFe-hexaferrite, BaFeHF), growing its surface area from 5 to 30 m2/g, and promotion with potassium increased the CO capacity in isothermal RWGS-CL runs at 350–450 °C, where the hexaaluminate/hexaferrite structure is stable. Increasing H2-reduction temperature converts BaFeHAl to a thermally stable BaFeHF modification that contains additional Ba-O-Fe bridges in its structure, reinforcing the connection between alternatively stacked spinel blocks. This material displayed the highest CO capacity of 400 µmol/g at isothermal RWGS-CL run conducted at 550 °C due to increased concentration of oxygen vacancies reflected by greater surface Fe2+/Fe3+ ratio detected by XPS. The results demonstrate direct connection between CO capacity measured in RWGS-CL experiments and calculated CO2 conversion.
- 21 May 2020
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 12 (24) , 12993-13000
Electrospun nanofibers with surface oriented lamellar patterns and their potential applications
Surface oriented lamellar structures in ceramic nanofibers for catalysis and energy storage.
- 21 May 2020
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 12 (24) , 12993-13000
Electrospun nanofibers with surface oriented lamellar patterns and their potential applications
Surface oriented lamellar structures in ceramic nanofibers for catalysis and energy storage.
- 8 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (22) , 24855-24867
Electrospun Fe–Al–O Nanobelts for Selective CO2 Hydrogenation to Light Olefins
Ceramic nanobelts consisting of Fe-Al-O spinel, modified with potassium were synthesized as catalysts for CO2 hydrogenation into hydrocarbons for the first time. Nanobelts and hollow nanofibers were produced utilizing the internal heat released by oxidation of the organic component within the fibers. This extremely fast and short heating facilitated crystallization of the desired phase, while maintaining small grains and large surface area. We investigated the effects of mat thickness, composition, and heating rate on the final morphology. A general transformation mechanism for electrospun nanofibers that correlates the mat's thickness and rate of oxidation during thermal treatment was proposed. The catalytic performance of carburized ceramic K/Fe-Al-O nanobelts was compared to K/Fe-Al-O spinel powder. Optimized electrospun catalyst showed superior carbon dioxide conversion of 48% and a selectivity of 52% to light C2-C5 olefins, while the powder catalyst produced mainly C6+ hydrocarbons. Characterization of steady state catalytic materials by EDAX, XRD, XPS, HRTEM and N2-adsorption methods revealed that high olefins selectivity of electrospun material is related to high extent of reduction of surface iron atoms due to more efficient interaction with the potassium promoter.
- 8 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (22) , 24855-24867
Electrospun Fe–Al–O Nanobelts for Selective CO2 Hydrogenation to Light Olefins
Ceramic nanobelts consisting of Fe-Al-O spinel, modified with potassium were synthesized as catalysts for CO2 hydrogenation into hydrocarbons for the first time. Nanobelts and hollow nanofibers were produced utilizing the internal heat released by oxidation of the organic component within the fibers. This extremely fast and short heating facilitated crystallization of the desired phase, while maintaining small grains and large surface area. We investigated the effects of mat thickness, composition, and heating rate on the final morphology. A general transformation mechanism for electrospun nanofibers that correlates the mat's thickness and rate of oxidation during thermal treatment was proposed. The catalytic performance of carburized ceramic K/Fe-Al-O nanobelts was compared to K/Fe-Al-O spinel powder. Optimized electrospun catalyst showed superior carbon dioxide conversion of 48% and a selectivity of 52% to light C2-C5 olefins, while the powder catalyst produced mainly C6+ hydrocarbons. Characterization of steady state catalytic materials by EDAX, XRD, XPS, HRTEM and N2-adsorption methods revealed that high olefins selectivity of electrospun material is related to high extent of reduction of surface iron atoms due to more efficient interaction with the potassium promoter.
- Open Access
Effect of Surface Chemistry and Crystallographic Parameters of TiO2 Anatase Nanocrystals on Photocatalytic Degradation of Bisphenol A
The photocatalytic activity of a series of anatase TiO2 materials with different amounts of exposed (001) facets (i.e., 12% (TiO2-1), 38% (TiO2-3), and 63% (TiO2-3)) was tested in a batch slurry reactor towards liquid-phase bisphenol A (BPA, c0(BPA) = 10 mg/L, ccat. = 125 mg/L) degradation. Photo-electrochemical and photo-luminescence measurements revealed that with the increasing amount of exposed anatase (001) facets, the catalysts generate more electron-hole pairs and OH∙ radicals that participate in the photocatalytic mineralization of pollutants dissolved in water. In the initial stages of BPA degradation, a correlation between % exposure of (001) facets and catalytic activity was developed, which was in good agreement with the findings of the photo-electrochemical and photo-luminescence measurements. TiO2-1 and TiO2-3 solids achieved 100% BPA removal after 80 min in comparison to the TiO2-2 sample. Adsorption of BPA degradation products onto the TiO2-2 catalyst surface was found to have a detrimental effect on the photocatalytic performance in the last stage of the reaction course. Consequently, the global extent of BPA mineralization decreased with the increasing exposure of anatase (001) facets. The major contribution to the enhanced reactivity of TiO2 anatase (001) surface is the Brønsted acidity resulting from dissociative chemisorption of water on a surface as indicated by FTIR, TPD, and MAS NMR analyses.
Open AccessEffect of Surface Chemistry and Crystallographic Parameters of TiO2 Anatase Nanocrystals on Photocatalytic Degradation of Bisphenol A
The photocatalytic activity of a series of anatase TiO2 materials with different amounts of exposed (001) facets (i.e., 12% (TiO2-1), 38% (TiO2-3), and 63% (TiO2-3)) was tested in a batch slurry reactor towards liquid-phase bisphenol A (BPA, c0(BPA) = 10 mg/L, ccat. = 125 mg/L) degradation. Photo-electrochemical and photo-luminescence measurements revealed that with the increasing amount of exposed anatase (001) facets, the catalysts generate more electron-hole pairs and OH∙ radicals that participate in the photocatalytic mineralization of pollutants dissolved in water. In the initial stages of BPA degradation, a correlation between % exposure of (001) facets and catalytic activity was developed, which was in good agreement with the findings of the photo-electrochemical and photo-luminescence measurements. TiO2-1 and TiO2-3 solids achieved 100% BPA removal after 80 min in comparison to the TiO2-2 sample. Adsorption of BPA degradation products onto the TiO2-2 catalyst surface was found to have a detrimental effect on the photocatalytic performance in the last stage of the reaction course. Consequently, the global extent of BPA mineralization decreased with the increasing exposure of anatase (001) facets. The major contribution to the enhanced reactivity of TiO2 anatase (001) surface is the Brønsted acidity resulting from dissociative chemisorption of water on a surface as indicated by FTIR, TPD, and MAS NMR analyses.