WYWei Yang

Wei Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Wei Yang has a total of 121 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Crack Suppression Strategies for Laser Cladding WMoTaNb High-Entropy Alloy Coatings on Steel Substrates

    by Shuaidan Lu, Meiling Du, Dui Zhao, Yinghui Zhou, Chen Ma, Wenting Shao, Yongming Ren, Rengen Ding, Wei Yang, Jian Chen

    Laser cladding of dissimilar materials can significantly improve the wear and corrosion resistance of substrate materials; however, cracking in the cladding layer often limits its widespread application. In this paper, a WMoTaNb coating was prepared on the surface of alloy structural steel (PCrNiMoV) using laser cladding technology. The effects of laser cladding parameters, substrate preheating, and the addition of a transition layer on the microstructure and cracking behavior of the cladding layer were investigated. The results show that the effective preparation of WMoTaNb high-entropy alloy coatings on steel substrates is achievable, with the cladding layer exhibiting metallurgical bonding with the substrate material. Among the laser cladding parameters, laser power significantly affects the morphology of the molten pool and element distribution. High power leads to substantial dilution of Fe from the substrate, resulting in the formation of Fe-, Ta-, and Nb-rich phases and increased defects such as porosity. Low power results in poor bonding between the coating and substrate and a large number of unmelted powder particles. The surface crack density of the coating under direct cladding was 0.33 mm⁻¹. Substrate preheating reduced the number of surface cracks and improved the bonding strength between the coating and substrate. The crack suppression strategy combining substrate preheating with the addition of an Inconel 718 transition layer yielded a surface crack density of ~0.17 mm⁻¹, comparable to the substrate preheating condition alone (~0.14 mm⁻¹), representing a 48.5% reduction compared to the direct cladding process. However, this combined approach achieved the highest shear strength, with an average value of 419 MPa. This study provides guidance for crack suppression in laser-clad WMoTaNb high-entropy alloy coatings on steel substrates.

  • Laser-sharkskin biomimetic textures with MoS 2 composite coating for ultra-low friction TC6 titanium

    by Yan Xiaoni, Liu Yicong, Geng Nan, Guo Junde, Zhang Zhenyu, Yang Wei

    The TC6 titanium alloy used in components such as shock absorber struts and bearing seats shows certain levels of friction and wear. In order to improve its service life and performance, this paper adopts femtosecond laser to prepare dentate bionic texture surface, and uses MoS 2 composite coating to enhance the lubrication effect. The friction velocity of TC6 surface under 6 N load and 20 mm s −1 is studied. Tribological properties under the condition of 10 min friction time. The results show that: (1) Dentate texture can effectively reduce friction and wear phenomenon, and is affected by area density, among which the texture array with a density of 14% has the best anti-friction and wear effect. Compared with smooth surface, the friction coefficient is reduced by about 71%, and the wear volume is reduced by about 98%, which is attributed to the hardening effect of laser on the texture edge to make it withstand greater contact stress. The existence of texture pit reduces the actual friction contact surface, and has a certain absorption effect on abrasive debris, thus slowing down the phenomenon of abrasive wear in the friction process. (2) The layered structure of MoS 2 composite coating greatly improves the surface lubrication effect. Similarly, 14% density is the optimal anti-friction wear-resistant texture array, and the friction coefficient and wear volume are only 26% and 0.68% of the smooth surface. The coating medium inside the texture pit is continuously transported to the friction interface, playing a role in continuous lubrication. The synergistic effect of the dentate texture and MoS 2 composite coating makes the tribological properties of TC6 greatly improved.

  • Open Access

    Effects of Si Target Power on the Mechanical Properties and Antioxidation and Antiablation Properties of Magnetron-Sputtered (WMoTaNb)SiN Refractory High-Entropy Nitride Films

    by Xiangyu Wu, Shangkun Wu, Wenting Shao, Jian Chen, Wei Yang

    (WMoTaNb)SiN refractory high-entropy nitride films were deposited via magnetron cosputtering, and the Si content was systematically regulated by varying the Si target power to investigate its influence on the microstructure, mechanical properties, oxidation resistance, and oxyhydrogen-flame ablation behavior. All the films exhibited dense columnar architectures with a distinct FCC + BCC dual-phase structure, whereas increasing the Si target power led to a gradual increase in the deposition rate and Si incorporation. The mechanical properties displayed a non-monotonic relationship with the Si target power, with film applied at an intermediate level of Si target power showing the highest hardness, approximately 28.5 GPa, and improved elastic recovery. Tribological evaluations using a GCr15 steel ball revealed that this film exhibited the lowest wear rate of 4.1 × 10−6 mm3·N−1·m−1 and a narrower wear track, which was attributed to reduced plastic deformation and the development of an oxygen-enriched tribofilm during sliding. High-temperature oxidation at 1000 °C in air revealed that Si incorporation significantly modified oxide-scale evolution by refining the oxidation products and altering the scale architecture, while the protection of the scale was governed by its continuity and compactness rather than its thickness alone. Oxyhydrogen-flame ablation tests revealed that the degradation behavior was primarily driven by the competition between oxidation-induced mass increase and ablation-induced material loss, with localized film disruption and substrate exposure playing a decisive role. In summary, the findings illustrate that an optimal Si target power establishes a favorable equilibrium between mechanical strength, tribological efficiency, oxidation resistance, and ablation performance, underscoring the potential of (WMoTaNb)SiN films for protective applications in complex mechanical and extreme thermal environments.

  • Open Access

    The Electrochemical Characteristics and Corrosion Resistance of a Low-Melting-Point Al49Sn21Zn16Pb14 Alloy in NaCl Solution

    by Xiaofei Yao, Weihua Wang, Xiaoling Qi, Yunkun Lv, Wei Yang, Yufei Ma, Jian Chen

    In this study, we prepared an innovative corrosion-resistant and low-melting-point Al49Sn21Zn16Pb14 alloy, and its microstructure was characterized. The corrosion resistance of the Al49Sn21Zn16Pb14 alloy in a NaCl solution with different concentrations was tested via electrochemical and immersion methods. In addition, the corrosion morphologies and products were analyzed via scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray diffraction (XRD), and the effects of the NaCl solution’s concentration on the corrosion resistance of the Al49Sn21Zn16Pb14 alloy were studied. The results showed that the melting point of the Al49Sn21Zn16Pb14 alloy was only 356.8 °C, and the melting temperature range was 356.8–377.6 °C. The microstructure of the Al49Sn21Zn16Pb14 alloy was dendritic, eutectic, and peritectic, and it had a face-centered cube (FCC) composition in the solid solution phase. The dendrite structure comprised an Al-rich solid solution primarily in the interdendrites and a Zn-rich solid solution mostly in the dendrites; the eutectic structure mainly consisted of Sn- and Pb-rich solid solutions; and the peritectic structure mainly comprised Zn- and Sn-rich solid solutions. In NaCl solutions of different concentrations, the Al49Sn21Zn16Pb14 alloy is generally corrosive; the corrosion rate of the Al49Sn21Zn16Pb14 alloy in 3.5% NaCl solution was 1.97 × 10−2 mm/a; and the corrosion surface was loose or cracking. The corrosion products attached to the corrosion surface of the alloys mainly comprised Al and Zn oxides, while Sn and Pb corroded to form Sn and Pb oxides, which dissolved or fell off to form microholes or pores on the corrosion surface of the Al49Sn21Zn16Pb14 alloy. With an increase in the NaCl solution’s concentration, the degree of corrosion products that fell off or dissolved increased, and thus, the Al49Sn21Zn16Pb14 alloy’s corrosion rate increased. In 10.5% and 14% NaCl solutions, the amount of Al oxides in the corrosion products increased, and the locally dense corrosion product that formed on the corrosion surface of the Al49Sn21Zn16Pb14 alloy cracked and could not protect the matrix. The locally dense corrosion products on the surface of the Al49Sn21Zn16Pb14 alloy in NaCl solutions therefore could not improve the corrosion resistance.


  • High‐temperature tribological behavior of hydrothermal MoS 2 coating on TC6 surface treated by MAO method

    by Junde Guo, Kaituo Feng, Xiaopeng Wang, Wei Yang, Zhaohui Cheng, Biao Sun, Wei Cao, Junhu Meng

    Titanium alloys have excellent mechanical properties, but poor tribological properties limit their application as dynamic friction components. Micro‐arc oxidation (MAO) is a technique to generate a ceramic layer on the metal surface to obtain better wear resistance, but the structure of the ceramic layer leads to a high coefficient of friction. In this study, MAO–MoS 2 composite coatings were prepared on the surface of titanium alloy (TC6) by a combination of MAO and hydrothermal reaction. The tribological performance of the composite coatings was investigated by a ball‐on‐disk high‐temperature tribometer under room temperature to 300°C, and the corresponding lubrication mechanism was revealed. The results show that the average friction coefficient of the composite coating is reduced by 89.1% and the wear rate is reduced by 91.4% compared to the pure TC6 at 300°C, which is attributed to the introduction of the MAO ceramic layer and MoS 2 lubrication element synergistically improves the friction reduction and wear resistance of TC6. The findings of this study are expected to expand the engineering applications of titanium alloy components in aerospace and other related fields.


  • Open Access

    The nanocrystalline and high density dislocation-Enabled ultrahigh strength and ductility of Al0.4Co0.5V0.2FeNi high entropy alloy

    by Yuan Li, Zhong Yang, Ping Wang, Hongbo Duan, Wei Yang, Zhijun Ma, Chao Wu, Jianping Li