Jiří Huzlík
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiří Huzlík has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Roman Ličbinský
Transport Res Ctr, Lisenska 33a, Brno 63600, Czech Republic
8 shared publications - Jitka Hegrová
Transport Research Centre, Líšeňská 33a, 636 00 Brno, Czech Republic
5 shared publications - Martina Bucková
Transport Research Centre, Líšeňská 33a, 636 00 Brno, Czech Republic
5 shared publications - Vilma Jandová
Transport Research Centre, Brno, Czech Republic
5 shared publications - František Božek
Department of Population Protection, University of Defence, Brno, Czech Republic
4 shared publications - Jiří Pospíšil
Energy Institute, Brno University of Technology, 616 69 Brno, Czech Republic
4 shared publications
Latest Publications
- 17 October 2026
- Published by Elsevier in Environmental Research
- Vol. 310
Characterisation of particle-bound PAHs emitted from a residential wood-burning stove and their dependence on combustion phases
- 17 October 2026
- Published by Elsevier in Environmental Research
- Vol. 310
Characterisation of particle-bound PAHs emitted from a residential wood-burning stove and their dependence on combustion phases
- Open Access
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Characterization of particle-bound PAHs emitted from residential wood-burning stove and their dependence on combustion phases
Residential wood combustion is a major global source of bad air quality and respiratory illness, yet the real-time shifts in emission profiles during a single burn cycle remain poorly understood. This study investigates the phase-resolved dynamics and size distributions of particle-bound polycyclic aromatic hydrocarbons (PAHs) from three widespread temperate wood species (beech, black locust, and spruce) burned under nominal conditions in a standard residential stove. Aerosol emissions were separated using a cascade impactor across five distinct combustion phases, with PAH masses quantified via GC-MS/MS. Particulate and PAH emissions peaked sharply during initial ignition and flaming, caused by intense devolatilization and localized oxygen deficits. Across all fuels and phases, the physical size distribution remained monomodal, peaking at an aerodynamic diameter of ~0.1 µm, with the highly respirable fine fraction (PM1) representing 74–90% of the total mass. While particle size did not determine specific PAHs profiles, chemical composition was influenced by fuel type and combustion stage. Hardwoods (beech and black locust) consistently emitted low-molecular-weight (LMW) PAHs. Softwood (spruce), however, generated an intense initial release of high-molecular-weight (HMW) PAHs, before shifting to LMW species during the burnout phase. These findings demonstrate that highly toxic PAHs are bound on ultrafine carriers throughout the entire combustion cycle, highlighting the possibility of exposure risks.
- 1 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterization of particle-bound PAHs emitted from residential wood-burning stove and their dependence on combustion phases
Residential wood combustion is a major global source of bad air quality and respiratory illness, yet the real-time shifts in emission profiles during a single burn cycle remain poorly understood. This study investigates the phase-resolved dynamics and size distributions of particle-bound polycyclic aromatic hydrocarbons (PAHs) from three widespread temperate wood species (beech, black locust, and spruce) burned under nominal conditions in a standard residential stove. Aerosol emissions were separated using a cascade impactor across five distinct combustion phases, with PAH masses quantified via GC-MS/MS. Particulate and PAH emissions peaked sharply during initial ignition and flaming, caused by intense devolatilization and localized oxygen deficits. Across all fuels and phases, the physical size distribution remained monomodal, peaking at an aerodynamic diameter of ~0.1 µm, with the highly respirable fine fraction (PM1) representing 74–90% of the total mass. While particle size did not determine specific PAHs profiles, chemical composition was influenced by fuel type and combustion stage. Hardwoods (beech and black locust) consistently emitted low-molecular-weight (LMW) PAHs. Softwood (spruce), however, generated an intense initial release of high-molecular-weight (HMW) PAHs, before shifting to LMW species during the burnout phase. These findings demonstrate that highly toxic PAHs are bound on ultrafine carriers throughout the entire combustion cycle, highlighting the possibility of exposure risks.
- Open Access
- 10 January 2025
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 32 (5) , 2455-2466
Release of PAHs from reclaimed asphalt mixtures into the water environment after passivation by cold in-place recycling technology
The paper deals with an analysis of the amount of 16 polycyclic aromatic hydrocarbons (PAHs (Polycyclic aromatic hydrocarbons—16 defined by US EPA.)) released from reclaimed asphalt mixtures used in base layers of road surfaces and in binder layers in road construction using cold in-place recycling. For the ten samples tested, the sum of 16 PAHs was determined directly for the crushed asphalt mixture and for its 24-h leachate. The crushed asphalt samples were used to make cylindrical asphalt specimens of the cold recycling mixture. The asphalt specimens were prepared to simulate as realistically as possible the use of the mixtures in road reconstructions implementing the cold in-place recycling technology, which should ensure the passivation of PAHs. The asphalt specimens were subjected to a dynamic leaching test under laboratory conditions with regular replacement of the leaching liquid. The results showed that the concentration of PAHs released into the water environment from the test specimens (passivated material) was approximately 40–50% lower than the amount of PAHs released from the asphalt mixtures in the 24-h leaching test. When compared to the input PAH concentrations in the asphalt mixtures (36–1323 mg.kg−1), on average, only 0.15% of PAHs is released from the passivated material. Dynamic leaching test has shown that the wrapping of the original asphalt mixture with a new binder and its subsequent compaction leads to the preservation of PAHs in the original material at such a level that their total concentrations are reduced by two orders of magnitude.
- 10 January 2025
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 32 (5) , 2455-2466
Open AccessRelease of PAHs from reclaimed asphalt mixtures into the water environment after passivation by cold in-place recycling technology
The paper deals with an analysis of the amount of 16 polycyclic aromatic hydrocarbons (PAHs (Polycyclic aromatic hydrocarbons—16 defined by US EPA.)) released from reclaimed asphalt mixtures used in base layers of road surfaces and in binder layers in road construction using cold in-place recycling. For the ten samples tested, the sum of 16 PAHs was determined directly for the crushed asphalt mixture and for its 24-h leachate. The crushed asphalt samples were used to make cylindrical asphalt specimens of the cold recycling mixture. The asphalt specimens were prepared to simulate as realistically as possible the use of the mixtures in road reconstructions implementing the cold in-place recycling technology, which should ensure the passivation of PAHs. The asphalt specimens were subjected to a dynamic leaching test under laboratory conditions with regular replacement of the leaching liquid. The results showed that the concentration of PAHs released into the water environment from the test specimens (passivated material) was approximately 40–50% lower than the amount of PAHs released from the asphalt mixtures in the 24-h leaching test. When compared to the input PAH concentrations in the asphalt mixtures (36–1323 mg.kg−1), on average, only 0.15% of PAHs is released from the passivated material. Dynamic leaching test has shown that the wrapping of the original asphalt mixture with a new binder and its subsequent compaction leads to the preservation of PAHs in the original material at such a level that their total concentrations are reduced by two orders of magnitude.
- Open Access
- 6 September 2024
- Published by Elsevier in Atmospheric Environment: X
- Vol. 23
Comparison of high mileage LPG cars in different technical condition in Czechia: Particle-bound PAHs
- 6 September 2024
- Published by Elsevier in Atmospheric Environment: X
- Vol. 23
Open AccessComparison of high mileage LPG cars in different technical condition in Czechia: Particle-bound PAHs
- Open Access
- 1 September 2023
- Published by Springer Nature in Journal of Applied Phycology
- Vol. 35 (5) , 2241-2256
Study of bioaccumulation of Cr, Ni and Zn by the green alga Desmodesmus subspicatus and assessment of the toxic effect of selected elements and their mixtures on algae cells
Toxicity assessment of K2Cr2O7, ZnCl2 and NiCl2.6H2O focusing on the green unicellular alga Desmodesmus subspicatus showed that Ni was the most toxic (EC50 = 0.121 mg L−1), followed by Cr (EC50 = 0.357 mg L−1) and Zn (EC50 = 0.968 mg L−1). The alga was exposed to solutions of the individual metals and their mixtures (Zn + Ni, Zn + Ni + Cr). After 48, 72 and 96 h of exposure, the accumulation of Zn, Ni and Cr in algal cells was assessed. Moreover, the change in toxicity of the metals, the concentration of selected biogenic elements (Ca, Na, Mg, S, K, P, Mn) in algal cells and the rate of metal removal from the solutions were also analysed. In the case of single-metal solutions, for Zn and Cr, the toxicity and accumulation in algal cells decreased over the 96 h of the experiment, whereas for Ni as well as for the binary and ternary mixtures the toxicity and accumulation increased. Significant correlations between the amount of metals accumulated in the cells and the inhibition of growth rates were observed. The content of selected biogenic elements in algal cells decreased over time in all treatments with added metals as well as in the control group, and after 96 h was higher in all treatments with addition of Ni compared to the control group and single-metal solutions of Zn and Cr. The highest removal of the metal from the solution occurred in the case of the single metal solution of Zn, where 83.4% of Zn was removed from the solution in 96 h.
- 1 September 2023
- Published by Springer Nature in Journal of Applied Phycology
- Vol. 35 (5) , 2241-2256
Open AccessStudy of bioaccumulation of Cr, Ni and Zn by the green alga Desmodesmus subspicatus and assessment of the toxic effect of selected elements and their mixtures on algae cells
Toxicity assessment of K2Cr2O7, ZnCl2 and NiCl2.6H2O focusing on the green unicellular alga Desmodesmus subspicatus showed that Ni was the most toxic (EC50 = 0.121 mg L−1), followed by Cr (EC50 = 0.357 mg L−1) and Zn (EC50 = 0.968 mg L−1). The alga was exposed to solutions of the individual metals and their mixtures (Zn + Ni, Zn + Ni + Cr). After 48, 72 and 96 h of exposure, the accumulation of Zn, Ni and Cr in algal cells was assessed. Moreover, the change in toxicity of the metals, the concentration of selected biogenic elements (Ca, Na, Mg, S, K, P, Mn) in algal cells and the rate of metal removal from the solutions were also analysed. In the case of single-metal solutions, for Zn and Cr, the toxicity and accumulation in algal cells decreased over the 96 h of the experiment, whereas for Ni as well as for the binary and ternary mixtures the toxicity and accumulation increased. Significant correlations between the amount of metals accumulated in the cells and the inhibition of growth rates were observed. The content of selected biogenic elements in algal cells decreased over time in all treatments with added metals as well as in the control group, and after 96 h was higher in all treatments with addition of Ni compared to the control group and single-metal solutions of Zn and Cr. The highest removal of the metal from the solution occurred in the case of the single metal solution of Zn, where 83.4% of Zn was removed from the solution in 96 h.
- Open Access
- 21 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 13 (1) , 20
Development of New Health Risk Assessment of Nanoparticles: EPA Health Risk Assessment Revised
The concentration of nanoparticles in the ambient air can lead to induced toxicities; however, it appears that nanoparticles’ unique properties are completely omitted when assessing health risks. This paper aims to enhance the EPA health risk assessment by incorporating two new variables that consider the size of nanoparticles: the toxicity multiplier and the size multiplier. The former considers the qualitative aspect of the size of particles within a concentration, whilst the latter takes into account the effects associated with the number of particles of the specific i-th size distribution interval. To observe the impact of the new variables, a case study was performed. The studied element was cadmium, which was measured using ICP-MS to discover concentrations of size fractions, ranging from −5, which was almost 24 times higher compared with the current method. The contribution of nanoparticles to the risk value grew from barely 6% to an alarming 88%. Therefore, the enhanced method can lead to more realistic results when assessing the health risks of nanoparticles.
- 21 December 2022
- Published by MDPI AG in Nanomaterials
- Vol. 13 (1) , 20
Open AccessDevelopment of New Health Risk Assessment of Nanoparticles: EPA Health Risk Assessment Revised
The concentration of nanoparticles in the ambient air can lead to induced toxicities; however, it appears that nanoparticles’ unique properties are completely omitted when assessing health risks. This paper aims to enhance the EPA health risk assessment by incorporating two new variables that consider the size of nanoparticles: the toxicity multiplier and the size multiplier. The former considers the qualitative aspect of the size of particles within a concentration, whilst the latter takes into account the effects associated with the number of particles of the specific i-th size distribution interval. To observe the impact of the new variables, a case study was performed. The studied element was cadmium, which was measured using ICP-MS to discover concentrations of size fractions, ranging from −5, which was almost 24 times higher compared with the current method. The contribution of nanoparticles to the risk value grew from barely 6% to an alarming 88%. Therefore, the enhanced method can lead to more realistic results when assessing the health risks of nanoparticles.
- 3 November 2022
- Published by Royal Society of Chemistry (RSC) in Organic & Biomolecular Chemistry
- Vol. 21 (1) , 93-97
Common xanthene fluorescent dyes are visible-light activatable CO-releasing molecules
Fluorescein, eosin and rose bengal, xanthene diagnostic dyes, are releasing carbon monoxide, formic and phthalic acids upon irradiation by visible light in aqueous media, previously unreported photolysis products.
- 3 November 2022
- Published by Royal Society of Chemistry (RSC) in Organic & Biomolecular Chemistry
- Vol. 21 (1) , 93-97
Common xanthene fluorescent dyes are visible-light activatable CO-releasing molecules
Fluorescein, eosin and rose bengal, xanthene diagnostic dyes, are releasing carbon monoxide, formic and phthalic acids upon irradiation by visible light in aqueous media, previously unreported photolysis products.
- Open Access
- 27 July 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (15) , 9186
Conditions Affecting Wind-Induced PM10 Resuspension as a Persistent Source of Pollution for the Future City Environment
Air pollution by particulate matter (PM) in cities is an ongoing problem with increasing severity. The biggest PM contributors are traffic and domestic fire burning. With the shift towards electromobility and the use of low-emission fuels, attention should be shifted to less mentioned sources of pollution. Such sources of pollution include wind-induced resuspension. This study focuses on determining the threshold wind speed causing the resuspension of particulate matter (TWSR) with aerodynamic diameter smaller than 10 µm. A methodology is introduced that examines how data could be treated to identify its characteristics (for locations where only PM10 data are available). The most significant monitored parameters are air humidity, wind direction, time of the day, and surface type. The characteristic wind speeds causing resuspension are identified in four locations for different times of day. It was proven that at times of intense human activity, particles are lifted by wind more easily. The mean threshold wind speed causing resuspension in the studied urban environment was identified as 1.58 m/s at a height of 2 m above the surface. The wind speeds were also compared with experimental studies of resuspension. The results proved correspondence between the identified wind speeds and the experimental results.
- 27 July 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (15) , 9186
Open AccessConditions Affecting Wind-Induced PM10 Resuspension as a Persistent Source of Pollution for the Future City Environment
Air pollution by particulate matter (PM) in cities is an ongoing problem with increasing severity. The biggest PM contributors are traffic and domestic fire burning. With the shift towards electromobility and the use of low-emission fuels, attention should be shifted to less mentioned sources of pollution. Such sources of pollution include wind-induced resuspension. This study focuses on determining the threshold wind speed causing the resuspension of particulate matter (TWSR) with aerodynamic diameter smaller than 10 µm. A methodology is introduced that examines how data could be treated to identify its characteristics (for locations where only PM10 data are available). The most significant monitored parameters are air humidity, wind direction, time of the day, and surface type. The characteristic wind speeds causing resuspension are identified in four locations for different times of day. It was proven that at times of intense human activity, particles are lifted by wind more easily. The mean threshold wind speed causing resuspension in the studied urban environment was identified as 1.58 m/s at a height of 2 m above the surface. The wind speeds were also compared with experimental studies of resuspension. The results proved correspondence between the identified wind speeds and the experimental results.
- Open Access
The Relationship among Precipitation, Application of Salt in Winter Road Maintenance and the Quality of Waterways and Soil around Motorway
Construction of motorways and road traffic bring a new line element into the landscape, which fundamentally influences the local hydrological regime and water quality. Impermeable surfaces are introduced into the landscape, affecting the natural infiltration of water in the environment. The aim of the present research was to assess the long-term historical development of changes in the landscape retention potential due to construction of the D1 motorway in the Jihlava region and also evaluate the impact of winter maintenance on the quality of surface waters and soils. During the reference period, the research area showed an increase in land take and related increases in soil sealing by impermeable surfaces due to the construction of the D1 motorway. This fact has clearly contributed to the deterioration of the retention potential of the landscape in the area. Chloride concentrations of both matrices were evaluated in relation to the amount of de-icing salt applied at the sites and precipitation recorded in this region. Water samples collected at the outflow contained in all cases higher concentrations of chloride than samples of the inflow water. The highest chloride concentration in soil was measured in samples collected at a distance of 2 m from the road.
Open AccessThe Relationship among Precipitation, Application of Salt in Winter Road Maintenance and the Quality of Waterways and Soil around Motorway
Construction of motorways and road traffic bring a new line element into the landscape, which fundamentally influences the local hydrological regime and water quality. Impermeable surfaces are introduced into the landscape, affecting the natural infiltration of water in the environment. The aim of the present research was to assess the long-term historical development of changes in the landscape retention potential due to construction of the D1 motorway in the Jihlava region and also evaluate the impact of winter maintenance on the quality of surface waters and soils. During the reference period, the research area showed an increase in land take and related increases in soil sealing by impermeable surfaces due to the construction of the D1 motorway. This fact has clearly contributed to the deterioration of the retention potential of the landscape in the area. Chloride concentrations of both matrices were evaluated in relation to the amount of de-icing salt applied at the sites and precipitation recorded in this region. Water samples collected at the outflow contained in all cases higher concentrations of chloride than samples of the inflow water. The highest chloride concentration in soil was measured in samples collected at a distance of 2 m from the road.
- Open Access
- 15 May 2020
- Published by MDPI AG in Atmosphere
- Vol. 11 (5) , 510
Air Quality in Brno City Parks
Parks embody an important element of urban infrastructure and a basic type of public space that shapes the overall character of a city. They form a counterweight to built-up areas and public spaces with paved surfaces. In this context, parks compensate for the lack of natural, open landscapes in cities and thus have a fundamental impact on the quality of life of their inhabitants. For this reason, it is important to consider the quality of the environment in urban parks, air quality in particular. Concentrations of gaseous pollutants, namely, nitric oxide (NO), nitrogen dioxide (NO2), and ozone (O3), were measured in parks of Brno, the second-largest city in the Czech Republic. Relevant concentration values of PM10 solids were determined continuously via the nephelometric method, followed by gravimetric method-based validation. The results obtained through the measurement of wind direction, wind speed, temperature, and relative humidity were used to identify potential sources of air pollution in parks. The “openair” and “openairmaps” packages from the OpenSource software R v. 3.6.2 were employed to analyze the effect of meteorological conditions on air pollution. Local polar concentration maps found use in localizing the most serious sources of air pollution within urban parks. The outcomes of the analyses show that the prevailing amount of the pollution determined at the measuring point most likely originates from the crossroads near the sampled localities. At the monitored spots, the maximum concentrations of pollutants are reached especially during the morning rush hour. The detailed time and spatial course of air pollution in the urban parks were indicated in the respective concentration maps capturing individual pollutants. Significantly increased concentrations of nitrogen oxides were established in a locality situated near a busy road (with the traffic intensity of 33,000 vehicles/d); this scenario generally applied to colder weather. The highest PM10 concentrations were measured at the same location and at an average temperature that proved to be the lowest within the entire set of measurements. In the main city park, unlike other localities, higher concentrations of PM10 were measured in warmer weather; such an effect was probably caused by the park being used to host barbecue parties.
- 15 May 2020
- Published by MDPI AG in Atmosphere
- Vol. 11 (5) , 510
Open AccessAir Quality in Brno City Parks
Parks embody an important element of urban infrastructure and a basic type of public space that shapes the overall character of a city. They form a counterweight to built-up areas and public spaces with paved surfaces. In this context, parks compensate for the lack of natural, open landscapes in cities and thus have a fundamental impact on the quality of life of their inhabitants. For this reason, it is important to consider the quality of the environment in urban parks, air quality in particular. Concentrations of gaseous pollutants, namely, nitric oxide (NO), nitrogen dioxide (NO2), and ozone (O3), were measured in parks of Brno, the second-largest city in the Czech Republic. Relevant concentration values of PM10 solids were determined continuously via the nephelometric method, followed by gravimetric method-based validation. The results obtained through the measurement of wind direction, wind speed, temperature, and relative humidity were used to identify potential sources of air pollution in parks. The “openair” and “openairmaps” packages from the OpenSource software R v. 3.6.2 were employed to analyze the effect of meteorological conditions on air pollution. Local polar concentration maps found use in localizing the most serious sources of air pollution within urban parks. The outcomes of the analyses show that the prevailing amount of the pollution determined at the measuring point most likely originates from the crossroads near the sampled localities. At the monitored spots, the maximum concentrations of pollutants are reached especially during the morning rush hour. The detailed time and spatial course of air pollution in the urban parks were indicated in the respective concentration maps capturing individual pollutants. Significantly increased concentrations of nitrogen oxides were established in a locality situated near a busy road (with the traffic intensity of 33,000 vehicles/d); this scenario generally applied to colder weather. The highest PM10 concentrations were measured at the same location and at an average temperature that proved to be the lowest within the entire set of measurements. In the main city park, unlike other localities, higher concentrations of PM10 were measured in warmer weather; such an effect was probably caused by the park being used to host barbecue parties.