Himadri Roy Ghatak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Himadri Roy Ghatak has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Sandeep Kumar Tripathi
Department of Chemical Engineering , 29759 Sant Longowal Institute of Engineering and Technology , Longowal - , Sangrur, Punjab , India
4 shared publications Kaleem Ahmad
Department of Chemical Engineering , Sant Longowal Institute of Engineering and Technology , Longowal 148106 , Punjab , India
3 shared publications- Nishi Kant Bhardwaj
Department of Paper and Packaging Technology, Indian Institute of Technology Roorkee, Saharanpur, India
3 shared publications P.P. Kundu
Department of Polymer Science & Technology, University of Calcutta, Kolkata 700009, India
2 shared publicationsS. M. Ahuja
Department of Chemical Engineering , Sant Longowal Institute of Engineering and Technology , Longowal 148106 , Punjab , India
2 shared publications- Sandeep Singh
Environmental Hydrology Division, National Institute of Hydrology, Roorkee, Uttarakhand, 247667, India
2 shared publications
Latest Publications
- Open Access
- 16 July 2024
- Published by IEOM Society International
Kinetic Study of Mineralization during Electrochemical Oxidation of Lamotrigine
To analyses the kinetic study of mineralization during electro-oxidation on Ti/DSA (Ta2O5-Ir2O5) and combined electro-oxidation and electro-coagulation on Stainless Steel (SS) anode of an anti-epileptic drug Lamotrigine (LAM) in synthetic wastewater over a specific charge. Four different reaction orders (0.5, 1, 1.5 and 2) were tested using the integral method of analysis by plotting concentration terms over specific charges to determine the exact rate kinetics for the mineralization. The effect of applied current density was evaluated at 50 ppm of sodium sulphate (Na2SO4) as supporting electrolyte, and the effect of supporting electrolyte concentration was also assessed at a current density of 1.38 mA/cm2 in 50 ppm LAM solution. As a result of (i) electro-oxidation experiments on LAM, carried out on Ti/DSA anode, and (ii) combined electro-oxidation and electro-coagulation experiments carried out on SS anode, based on the R-squared value of the mineralization curves, the first-order reaction rate was proposed.
- 16 July 2024
- Published by IEOM Society International
Open AccessKinetic Study of Mineralization during Electrochemical Oxidation of Lamotrigine
To analyses the kinetic study of mineralization during electro-oxidation on Ti/DSA (Ta2O5-Ir2O5) and combined electro-oxidation and electro-coagulation on Stainless Steel (SS) anode of an anti-epileptic drug Lamotrigine (LAM) in synthetic wastewater over a specific charge. Four different reaction orders (0.5, 1, 1.5 and 2) were tested using the integral method of analysis by plotting concentration terms over specific charges to determine the exact rate kinetics for the mineralization. The effect of applied current density was evaluated at 50 ppm of sodium sulphate (Na2SO4) as supporting electrolyte, and the effect of supporting electrolyte concentration was also assessed at a current density of 1.38 mA/cm2 in 50 ppm LAM solution. As a result of (i) electro-oxidation experiments on LAM, carried out on Ti/DSA anode, and (ii) combined electro-oxidation and electro-coagulation experiments carried out on SS anode, based on the R-squared value of the mineralization curves, the first-order reaction rate was proposed.
- 21 June 2023
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 18 (5)
Apparent and true mineralization during combined electro‐oxidation and electro‐coagulation on stainless steel anode
Present study is a novel attempt to experimentally verify that electrochemical treatment of organic pollutants on stainless steel (SS) anode is a combination of electro‐oxidation (EO) and electro‐coagulation (EC) with quantitative estimation of individual contributions of the two mechanisms. Target organic pollutants, metformin HCl (MET‐HCl) and lamotrigine (LAM), were electrochemically treated with SS anode for this purpose. Experiments were designed using central composite rotatable design (CCRD) to assess the effect of current density (CD) and supporting electrolyte concentration (SEC) as independent process parameters. Under all conditions, the process was experimentally verified to be a combination of EO and EC. For MET‐HCl, true mineralization (TM) as a result of EO contribution varied between 50.13% and 66.64%. EO contribution and resulting TM for LAM ranged from 37.5% to 61.83%. EC contributed 30.6%–31.84% towards MET‐HCl remediation causing the TOC to be transferred from the liquid to the sludge produced (SP). EC contribution was 23.68%–35.89% for LAM remediation. Thus, apparent mineralization (AM), the sum of EO and EC contributions, ranged from 80.63% to 97.79% for MET‐HCl and 61.18% to 96.82% for LAM.Process parameters were statistically optimized using response surface methodology (RSM) to simultaneously maximize TM and AM with minimal energy consumption and maximal current efficiency. The optimized conditions were 0.83 mA/cm2 CD and 86.66 ppm SEC for MET‐HCl. The corresponding values were 1.31 mA/cm2 CD and 79.51 ppm SEC for LAM.
- 21 June 2023
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 18 (5)
Apparent and true mineralization during combined electro‐oxidation and electro‐coagulation on stainless steel anode
Present study is a novel attempt to experimentally verify that electrochemical treatment of organic pollutants on stainless steel (SS) anode is a combination of electro‐oxidation (EO) and electro‐coagulation (EC) with quantitative estimation of individual contributions of the two mechanisms. Target organic pollutants, metformin HCl (MET‐HCl) and lamotrigine (LAM), were electrochemically treated with SS anode for this purpose. Experiments were designed using central composite rotatable design (CCRD) to assess the effect of current density (CD) and supporting electrolyte concentration (SEC) as independent process parameters. Under all conditions, the process was experimentally verified to be a combination of EO and EC. For MET‐HCl, true mineralization (TM) as a result of EO contribution varied between 50.13% and 66.64%. EO contribution and resulting TM for LAM ranged from 37.5% to 61.83%. EC contributed 30.6%–31.84% towards MET‐HCl remediation causing the TOC to be transferred from the liquid to the sludge produced (SP). EC contribution was 23.68%–35.89% for LAM remediation. Thus, apparent mineralization (AM), the sum of EO and EC contributions, ranged from 80.63% to 97.79% for MET‐HCl and 61.18% to 96.82% for LAM.Process parameters were statistically optimized using response surface methodology (RSM) to simultaneously maximize TM and AM with minimal energy consumption and maximal current efficiency. The optimized conditions were 0.83 mA/cm2 CD and 86.66 ppm SEC for MET‐HCl. The corresponding values were 1.31 mA/cm2 CD and 79.51 ppm SEC for LAM.
- 14 June 2022
- Published by Walter de Gruyter GmbH in Chemical Product and Process Modeling
- Vol. 18 (3) , 391-409
Response surface methodology (RSM) and artificial neural network (ANN) approach to optimize the photocatalytic conversion of rice straw hydrolysis residue (RSHR) into vanillin and 4-hydroxybenzaldehyde
Effective use of waste lignin is always a challenging task, technologies have been applied in the past to get value-added compounds from waste lignin. However, the existing technologies are not economical and efficient to produce the value-added chemicals. Alkali soluble lignin from rice straw hydrolysis residue (RSHR) is subjected to photocatalytic conversion into value-added compounds. Photocatalysis is one of the multifarious advanced oxidation processes (AOPs), carried out with TiO 2 nanoparticles under a 125 W UV bulb. Gas chromatography mass spectroscopy (GCMS) confirmed the formation of vanillin and 4-hydroxybenzaldehyde. RSM and ANN techniques are adopted to optimize the process conditions for the maximization of the products. The response one ( Y 1 ) vanillin (24.61 mg) and second response ( Y 2 ) 4-hydroxybenzaldehyde (19.51 mg) is obtained at the optimal conditions as 7.0 h irradiation time, 2.763 g/L catalyst dose, 15 g/L lignin concentration, and 14.26 g/L NaOH dose for alkali treatment, suggested by face-centered central composite design (CCD). RSM and ANN models are statistically analyzed in terms of RMSE, R 2 and AAD. For RSM the R 2 0.9864 and 0.9787 while for ANN 0.9875 and 0.9847, closer to one warrant the good fitting of the models. Therefore, in terms of higher precision and predictive ability of both models the ANN model showed excellence for both responses as compared to the RSM model.
- 14 June 2022
- Published by Walter de Gruyter GmbH in Chemical Product and Process Modeling
- Vol. 18 (3) , 391-409
Response surface methodology (RSM) and artificial neural network (ANN) approach to optimize the photocatalytic conversion of rice straw hydrolysis residue (RSHR) into vanillin and 4-hydroxybenzaldehyde
Effective use of waste lignin is always a challenging task, technologies have been applied in the past to get value-added compounds from waste lignin. However, the existing technologies are not economical and efficient to produce the value-added chemicals. Alkali soluble lignin from rice straw hydrolysis residue (RSHR) is subjected to photocatalytic conversion into value-added compounds. Photocatalysis is one of the multifarious advanced oxidation processes (AOPs), carried out with TiO 2 nanoparticles under a 125 W UV bulb. Gas chromatography mass spectroscopy (GCMS) confirmed the formation of vanillin and 4-hydroxybenzaldehyde. RSM and ANN techniques are adopted to optimize the process conditions for the maximization of the products. The response one ( Y 1 ) vanillin (24.61 mg) and second response ( Y 2 ) 4-hydroxybenzaldehyde (19.51 mg) is obtained at the optimal conditions as 7.0 h irradiation time, 2.763 g/L catalyst dose, 15 g/L lignin concentration, and 14.26 g/L NaOH dose for alkali treatment, suggested by face-centered central composite design (CCD). RSM and ANN models are statistically analyzed in terms of RMSE, R 2 and AAD. For RSM the R 2 0.9864 and 0.9787 while for ANN 0.9875 and 0.9847, closer to one warrant the good fitting of the models. Therefore, in terms of higher precision and predictive ability of both models the ANN model showed excellence for both responses as compared to the RSM model.
- Open Access
- 31 May 2022
- Published by The Korean Electrochemical Society - English Journal in Journal of Electrochemical Science and Technology
- Vol. 13 (2) , 292-307
Electrochemical Advanced Oxidation of Lamotrigine at Ti/DSA (Ta2O5-Ir2O5) and Stainless Steel Anodes
The study presents kinetics of degradation and mineralization of an anti-epileptic drug Lamotrigine (LAM) in the aqueous matrix by electrochemical advanced oxidation process (EAOP) on Ti/DSA (Ta2O5-Ir2O5) and Stainless Steel (SS) anodes using sodium sulphate as supporting electrolyte. On both the anodes, kinetic behaviour was pseudo-first-order for degradation as well as mineralization of LAM. On Ti/DSA anode, maximum LAM degradation of 75.42% was observed at an associated specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 100 ppm Na2SO4 concentration. Maximum mineralization attained was 44.83% at an associated specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 50 ppm concentration of Na2SO4 with energy consumption of 2942.71 kWh/kgTOC. Under identical conditions on SS anode, a maximum of 98.92% LAM degradation was marked after a specific charge (Q) of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 100 ppm concentration of Na2SO4. Maximum LAM mineralization on SS anode was 98.53%, marked at a specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 75 ppm concentration of Na2SO4, with energy consumption of 1312.17 kWh/kgTOC. Higher Mineralization Current Efficiency (MCE) values were attained for EAOP on SS anode for both degradation and mineralization due to occurrence of combined electro-oxidation and electro-coagulation process in comparison to EAOP on Ti/DSA anode due to occurrence of lone electro-oxidation process.
- 31 May 2022
- Published by The Korean Electrochemical Society - English Journal in Journal of Electrochemical Science and Technology
- Vol. 13 (2) , 292-307
Open AccessElectrochemical Advanced Oxidation of Lamotrigine at Ti/DSA (Ta2O5-Ir2O5) and Stainless Steel Anodes
The study presents kinetics of degradation and mineralization of an anti-epileptic drug Lamotrigine (LAM) in the aqueous matrix by electrochemical advanced oxidation process (EAOP) on Ti/DSA (Ta2O5-Ir2O5) and Stainless Steel (SS) anodes using sodium sulphate as supporting electrolyte. On both the anodes, kinetic behaviour was pseudo-first-order for degradation as well as mineralization of LAM. On Ti/DSA anode, maximum LAM degradation of 75.42% was observed at an associated specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 100 ppm Na2SO4 concentration. Maximum mineralization attained was 44.83% at an associated specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 50 ppm concentration of Na2SO4 with energy consumption of 2942.71 kWh/kgTOC. Under identical conditions on SS anode, a maximum of 98.92% LAM degradation was marked after a specific charge (Q) of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 100 ppm concentration of Na2SO4. Maximum LAM mineralization on SS anode was 98.53%, marked at a specific charge of 3.1 (Ah/litre) at a current density of 1.38 mA/cm2 and 75 ppm concentration of Na2SO4, with energy consumption of 1312.17 kWh/kgTOC. Higher Mineralization Current Efficiency (MCE) values were attained for EAOP on SS anode for both degradation and mineralization due to occurrence of combined electro-oxidation and electro-coagulation process in comparison to EAOP on Ti/DSA anode due to occurrence of lone electro-oxidation process.
- 17 May 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Chemical Engineering
- Vol. 66 (3) , 494-502
Evolved Gases and Unified Kinetic Model for Low-temperature Thermal Decomposition of Rice Straw Hydrolysis Residue for Possible Value Addition
Low-temperature thermal decomposition (LTTD) of Rice straw hydrolysis residue (RSHR) was studied using thermogravimetric analysis and Fourier Transform Infrared spectroscopy (TGA-FTIR) at different heating rates. During thermogravimetry, the maximum rate of mass loss of 135% per min was observed at 339 °C ( Tmax ) for heating rate of 50 °C per min. Tmax decreased to 323, 315, and 299 °C with decrease in heating rate to 40, 30, and 20 °C min−1, respectively. LTTD of RSHR yields volatile oxygenated organics – acids, esters, aldehydes, ketones, alcohols and phenols – as revealed by the FTIR spectra of evolved gases. At increased decomposition temperature, carbonyl moieties were less conjugated. The main gaseous products of LTTD were carbon dioxide, carbon monoxide, and methane. Kinetics of LTTD of RSHR was analysed using thermogravimetry results. Activation energy of LTTD followed a Lorentzian distribution with respect to residual mass fraction (RMF). Dependence of LTTD rate on RMF was found to adhere to the truncated Sestak and Berggren model.
- 17 May 2022
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Chemical Engineering
- Vol. 66 (3) , 494-502
Evolved Gases and Unified Kinetic Model for Low-temperature Thermal Decomposition of Rice Straw Hydrolysis Residue for Possible Value Addition
Low-temperature thermal decomposition (LTTD) of Rice straw hydrolysis residue (RSHR) was studied using thermogravimetric analysis and Fourier Transform Infrared spectroscopy (TGA-FTIR) at different heating rates. During thermogravimetry, the maximum rate of mass loss of 135% per min was observed at 339 °C ( Tmax ) for heating rate of 50 °C per min. Tmax decreased to 323, 315, and 299 °C with decrease in heating rate to 40, 30, and 20 °C min−1, respectively. LTTD of RSHR yields volatile oxygenated organics – acids, esters, aldehydes, ketones, alcohols and phenols – as revealed by the FTIR spectra of evolved gases. At increased decomposition temperature, carbonyl moieties were less conjugated. The main gaseous products of LTTD were carbon dioxide, carbon monoxide, and methane. Kinetics of LTTD of RSHR was analysed using thermogravimetry results. Activation energy of LTTD followed a Lorentzian distribution with respect to residual mass fraction (RMF). Dependence of LTTD rate on RMF was found to adhere to the truncated Sestak and Berggren model.
- 12 May 2022
- Published by Springer Nature
- p. 275-309
A Review on the Valorization of Biorefinery Based Waste Lignin: Exploratory Potential Market Approach
- 12 May 2022
- Published by Springer Nature
- p. 275-309
A Review on the Valorization of Biorefinery Based Waste Lignin: Exploratory Potential Market Approach
- Open Access
- 14 February 2022
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 34 (3) , 727-732
Electrochemical Mineralization Kinetics of Metformin
Present work analyzes the kinetic study of mineralization during electro-oxidation on Ti/DSA (Ta2O5-Ir2O5) and combined electro-oxidation and electro-coagulation on stainless steel anode of an antidiabetic drug metformin hydrochloride (MET-HCl) in synthetic wastewater over a specific charge. Four different reaction orders (0.5, 1, 1.5 and 2) were tested using the integral analysis method by plotting TOC concentration terms over specific charges to determine the exact rate kinetics for the mineralization. The effect of applied current density was evaluated at 50 ppm of sodium sulphate as supporting electrolyte, and the effect of supporting electrolyte concentration was also assessed at a current density of 0.93 mA/cm2 in 50 ppm MET-HCl solution. As a result of (i) electro-oxidation experiments on MET-HCl, carried out on Ti/DSA anode, and (ii) combined electro-oxidation and electro-coagulation experiments carried out on stainless steel anode, based on the R-squared value of the mineralization curves, the first-order reaction rate was proposed.
- 14 February 2022
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 34 (3) , 727-732
Open AccessElectrochemical Mineralization Kinetics of Metformin
Present work analyzes the kinetic study of mineralization during electro-oxidation on Ti/DSA (Ta2O5-Ir2O5) and combined electro-oxidation and electro-coagulation on stainless steel anode of an antidiabetic drug metformin hydrochloride (MET-HCl) in synthetic wastewater over a specific charge. Four different reaction orders (0.5, 1, 1.5 and 2) were tested using the integral analysis method by plotting TOC concentration terms over specific charges to determine the exact rate kinetics for the mineralization. The effect of applied current density was evaluated at 50 ppm of sodium sulphate as supporting electrolyte, and the effect of supporting electrolyte concentration was also assessed at a current density of 0.93 mA/cm2 in 50 ppm MET-HCl solution. As a result of (i) electro-oxidation experiments on MET-HCl, carried out on Ti/DSA anode, and (ii) combined electro-oxidation and electro-coagulation experiments carried out on stainless steel anode, based on the R-squared value of the mineralization curves, the first-order reaction rate was proposed.
- 1 February 2022
- Published by Elsevier in Journal of the Indian Chemical Society
- Vol. 99 (3)
Optimal production of vanillin and 4-hydroxybenzaldehyde from rice straw hydrolysis residue (RSHR) over TiO2/UV and ZnO/UV system
- 1 February 2022
- Published by Elsevier in Journal of the Indian Chemical Society
- Vol. 99 (3)
Optimal production of vanillin and 4-hydroxybenzaldehyde from rice straw hydrolysis residue (RSHR) over TiO2/UV and ZnO/UV system
- 1 November 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (56) , 31466-31480
Simulated process integration of wastewater electrooxidation with recuperated micro gas turbine for energy recovery
- 1 November 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (56) , 31466-31480
Simulated process integration of wastewater electrooxidation with recuperated micro gas turbine for energy recovery
- 25 September 2020
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 35 (4) , 559-568
Effect of introducing ozone in elemental chlorine free bleaching of pulp on generation of chlorophenolic compounds
Effect of using ozone before elemental chlorine free (ECF) bleaching of oxygen delignified wheat straw pulp produced following soda-anthraquinone pulping on bleaching effluent and pulp properties was studied. The effluent generated during bleaching of pulp contains high amount of adsorbable organic halogens (AOX), chemical oxygen demand (COD), biochemical oxygen demand (BOD) and highly toxic chlorophenolic compounds. This study is aimed to utilise green chemistry approach during bleaching of one of the abundantly used agro residue wheat straw for improving the quality of bleaching effluent and pulp properties. Introducing ozone stage before ECF bleaching resulted in significant reduction of chloriphenolic compounds like chlorocatechols by 48.9 %, chloroguaiacols by 33.3 %, chlorovanillins by 28.4 % and chlorophenols by 26.7 % in the effluent compared to those of control. Incorporation of ozone before ECF bleaching BOD, COD, AOX and colour were reduced by 40.0 %, 41.1 %, 46.7 % and 57.8 %, respectively, as compared to control. Optical properties like brightness and whiteness of the pulp bleached using ozone were also improved by 2.5 units and 4.0 units, respectively as compared to that with control.
- 25 September 2020
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 35 (4) , 559-568
Effect of introducing ozone in elemental chlorine free bleaching of pulp on generation of chlorophenolic compounds
Effect of using ozone before elemental chlorine free (ECF) bleaching of oxygen delignified wheat straw pulp produced following soda-anthraquinone pulping on bleaching effluent and pulp properties was studied. The effluent generated during bleaching of pulp contains high amount of adsorbable organic halogens (AOX), chemical oxygen demand (COD), biochemical oxygen demand (BOD) and highly toxic chlorophenolic compounds. This study is aimed to utilise green chemistry approach during bleaching of one of the abundantly used agro residue wheat straw for improving the quality of bleaching effluent and pulp properties. Introducing ozone stage before ECF bleaching resulted in significant reduction of chloriphenolic compounds like chlorocatechols by 48.9 %, chloroguaiacols by 33.3 %, chlorovanillins by 28.4 % and chlorophenols by 26.7 % in the effluent compared to those of control. Incorporation of ozone before ECF bleaching BOD, COD, AOX and colour were reduced by 40.0 %, 41.1 %, 46.7 % and 57.8 %, respectively, as compared to control. Optical properties like brightness and whiteness of the pulp bleached using ozone were also improved by 2.5 units and 4.0 units, respectively as compared to that with control.