Anisur Rahman

Next-generation polymeric materials are shifting toward adaptive and interactive behaviors of living systems; however, designing materials that can reversibly modulate optical properties under mechanical deformation while maintaining mechanical robustness remains a key challenge. Here, we report a mechanically robust vitrimer-based adaptive hybrid material (AHM) that exhibits a stretch-induced reversible transparency-to-opacity transition, enabled by the integration of dynamic interactions at the polymer-silica nanoparticle interface and controlled nanoparticle self-assembly. The AHM combines boronic ester-functionalized polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (S-Bpin) with diol-functionalized silica nanoparticles (diol-SiNPs) to form a hybrid network hosting both dynamic boronic ester and hydrogen-bonding interactions. These reversible linkages facilitate controlled nanoparticle self-assembly and enable strain-induced nanoparticle alignment/aggregation. Upon stretching, SiNP-rich domains align and aggregate within the polymer matrix, while local modulus mismatch between stiff aggregated SiNP/borylated-styrene-rich regions and the softer elastomeric midblock induces surface microwrinkle formation. These internal aggregates and surface wrinkles cooperatively enhance light scattering, producing the opaque state under strain. Furthermore, the tailored AHM exhibits high toughness, thermomechanical stability, reprocessability, and programmable shape-memory behavior. This work presents a dynamic interfacial design strategy for mechanically robust, optically reconfigurable, and reusable soft materials for adaptive optics, smart windows, sensing, soft robotics, and circular smart-material platforms.

The versatility of synthetic polymers has led to their continual and escalating production that has accompanied mismanagement at their end‐of‐life. Exploring and understanding complementary avenues to repurpose plastic waste beyond traditional mechanical recycling can unlock new opportunities in providing feedstock flexibility, securing supply chains, recovering valuable materials, and enabling new valorization paths. Chemical recycling allows for the return to monomers, tailored oligomers, and polymers, even from mixed states of post‐consumer waste plastics. This review article summarizes our research team's efforts on elucidating key insights surrounding plastic depolymerization and repolymerization into valorized products. We revealed organocatalyst design rules lead to highly effective and selective deconstruction of condensation polymers. The intricacies of tailoring the reaction environment to produce products of specific lengths and desired functionalities transform low‐value waste feedstocks into high‐performance materials with embedded circularity. Other types of polymers, including polyolefins and polyakenamers, have also been designed and converted into valuable products. There remain opportunities for further developments such as low‐energy and precision depolymerization, adoption of cutting‐edge small molecule transformation to access functionalized polymer scaffolds typically inaccessible otherwise, as well as precision design and understanding through the aid of advanced tools.

As part of the growing suite of technologies aimed at combatting rising temperatures, negative emissions technologies have become a powerful tool in the global effort to minimize the consequences of human-induced climate change. Among these, carbon removal from aqueous sources, which contain much higher carbon concentrations than the atmosphere, remains largely unexplored. Indeed, developing robust and efficient carbon capture materials for usage in complex aqueous environments remains a significant challenge. Here, we explore the potential of functionalizing polyvinylidene fluoride (PVDF) hollow fiber contactors grafted with a guanidinium-derived polymer sorbent for carbon removal from aqueous sources, including saline waters. Computational screening against amine-based analogs is utilized to identify guanidinium as a promising motif for bicarbonate (HCO₃ ^–) ions binding. To leverage this finding, synthesis of a guanidinium polymer and subsequent covalent grafting onto PVDF hollow fibers is employed to structured polymer–sorbent–grafted hollow fiber contactors. Our prototype achieves an initial HCO₃ ^– removal of 34% with an increase to 98% after four cycles. The functionalized fibers demonstrate aqueous stability over 13 adsorption/desorption cycles in model NaHCO₃ solutions where regeneration is facilitated by a mild pH swing. Importantly, the system maintains selective performance in the presence of competitive chloride ions over multiple cycles; carbon removal remained above 10% even at high (10:1) NaCl/NaHCO₃ ratios. These findings demonstrate the feasibility of sorbent-based aqueous carbon removal and highlight its potential as a promising approach for negative emissions.

While the potential use of copolymerized electrolytes in Li metal batteries is subject to intense investigation, the fundamental understanding of the nanoscale domain formation and its effect on Li⁺ transport is still lacking. In this study, we investigated the correlation between the Li⁺ transport mechanism and the miscibility of monomers in polymer blend electrolytes derived from the in situ copolymerization of methyl methacrylate (MMA) and vinylene carbonate (VC) in the presence of polyethylene glycol dimethyl ether (PEGDME) plasticizer and bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. The addition of a polar short chain plasticizer reduced the dynamic and structural heterogeneities of the electrolyte. Small-angle X-ray scattering (SAXS) measurements and coarse-grained molecular dynamics (MD) simulations were used to investigate the nanoscale structure of the electrolytes. The distribution of relaxation times corresponding to the three distinct diffusion mechanisms of the free and interfacial Li⁺ ions at the copolymer/plasticizer and electrolyte/SEI boundaries was analyzed in a broad temperature range to elucidate the Li⁺ transport mechanism. The chemical composition of the SEI and the contribution of a ceramic lithium lanthanum zirconium oxide (LLZO, Li₇La₃Zr₂O₁₂) phase on the interfacial resistance, salt degradation, and SEI stability were studied by X-ray photoelectron spectroscopy (XPS) depth profile analysis and electrochemical testing.

Solid polymer electrolytes (SPEs) hold great promise for the advancement of next-generation energy storage devices. However, the ion transport mechanism in SPEs remains poorly understood. In this study, we investigate blends of poly-(1-(3-sulfonatopropyl)-2-vinylpyridinium) (P2VPPS) and poly-(lithium (trifluoromethane)-sulfonimide methacrylate) (P-(MTFSI)-Li) of varying molar ratios to develop a mechanistic understanding of ionic conductivity in a miscible polyzwitterion/polyanion system. Polyanions can act as single-ion conductors, but conductivity is often prohibitively low due to the decreased segmental mobility and ion aggregation. Here, it is hypothesized that the introduction of a polyzwitterion would competitively interact with the polyanion charge groups to realize improvements in the conductivity. Attractive interactions between the polyanions and polyzwitterions are confirmed by the blend's increased glass transition temperature using the Gordon-Taylor equation. Notably, an ordered local nanostructure (∼24 Å) emerged in the P2VPPS/P-(MTFSI)Li system at certain compositions, as characterized by small-angle X-ray and neutron scattering (SAXS/SANS). Concurrent with the emergence of this structure, broadband dielectric spectroscopy confirmed improvements in ionic conductivity. The highest conductivity is observed at a specific blend ratio P2VPPS:P-(MTFSI)-Li = 0.2:1 in the glassy state and 0.3:1 in the rubbery state, corresponding to the lowest effective activation energy (E*). Coarse-grained molecular dynamics simulations further emphasize the role of complexation between polyzwitterion and polyanion chains, correlating with the emergence of a new peak in SAXS and SANS for the blends. This work provides a fresh perspective on the role of local structural design in developing SPEs and offers insights into the morphological effects on ionic conductivity.

Developing versatile, tough, and sustainable adhesives that function effectively in both wet and dry environments is a major challenge. Here, we report a bioinspired design for versatile, tough, and reversible adhesives upcycled from consumer poly(ethylene terephthalate) (PET) waste. Our approach uses solvent-free, room-temperature dynamic cross-linking of deconstructed PET macromonomers with a diacetoacetate cross-linker, generating a dynamic, vinylogous urethane–bonded, amphiphilic adhesive. Tunable cross-linker concentration and amphiphilicity yield versatile adhesives suitable for underwater, structural, and pressure-sensitive applications on diverse substrates. Our adhesive exhibits high lap-shear strength and work of debonding under both wet and dry conditions, outperforming common commercial adhesives. The dynamic bonds enable thermal repair, on-demand multicycle debonding/rebonding, facile removal, and chemical recycling. Our strategy of transforming plastic waste into versatile, tough, and reversible adhesives offers a sustainable solution for both plastic waste management and next-generation adhesive design while also providing a commercially viable pathway for valorizing plastic waste.