Wagner Reis da Costa Campos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wagner Reis da Costa Campos has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Luciana Iglésias Lourenço Lima
Federal University of Minas Gerais – Post Graduate Programme, Mechanical Engineering , Belo Horizonte, Minas Gerais, Brazil
2 shared publications- Luiza Esteves
Serviço de Integridade Estrutural (SEIES), Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN)
2 shared publications - Marco Antônio Dutra Quinan
Centro de Desenvolvimento da Tecnologia Nuclear, Brasil
2 shared publications - Mônica Maria de Abreu Mendonça Schvartzman
Centro de Desenvolvimento da Tecnologia Nuclear, Brasil
2 shared publications Alvaro Pritzel dos Santos
Universidade Federal do Rio Grande do Sul, Brasil
1 shared publication- Caroline Nazaré Gonçalves
Universidade Federal de Minas Gerais, Brasil
1 shared publication
Latest Publications
- Open Access
In Situ Evaluation of Epoxy Self-Healing Coating by Encapsulated Linseed Oil in Poly(Urea–Formaldehyde–Melamine) Microcapsules
The development of self-healing coatings represents a promising approach to enhance the durability of metal substrates exposed to corrosive environments, demanding thorough in situ investigations. In this study, poly(urea–formaldehyde–melamine) (PUF) microcapsules containing linseed oil (LO) were synthesized via in situ polymerization to act as healing agents in protective coatings. The microcapsules were characterized using scanning electron microscopy (SEM), optical microscopy (OM), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The capsules exhibited a regular spherical morphology with an average diameter of 96 µm and an LO encapsulation efficiency of 81 wt%. TGA confirmed their thermal stability up to 200 °C, while FTIR verified the successful encapsulation of LO. For performance evaluation, 10 wt% of the microcapsules was incorporated into an epoxy matrix and applied to carbon steel. Corrosion resistance was evaluated using electrochemical impedance spectroscopy (EIS) in 0.1 mol/L of NaCl solution over 500 h. The coating with microcapsules exhibited a |Z|0.01 of 106 Ω·cm2, higher than the 104 Ω·cm2 observed for the coating without microcapsules, indicating improved barrier properties. Raman spectroscopy confirmed the auto-oxidation of LO at damaged areas, evidencing the self-healing mechanism. Although full barrier recovery was not achieved, the system effectively delayed corrosion progression.
Open AccessIn Situ Evaluation of Epoxy Self-Healing Coating by Encapsulated Linseed Oil in Poly(Urea–Formaldehyde–Melamine) Microcapsules
The development of self-healing coatings represents a promising approach to enhance the durability of metal substrates exposed to corrosive environments, demanding thorough in situ investigations. In this study, poly(urea–formaldehyde–melamine) (PUF) microcapsules containing linseed oil (LO) were synthesized via in situ polymerization to act as healing agents in protective coatings. The microcapsules were characterized using scanning electron microscopy (SEM), optical microscopy (OM), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The capsules exhibited a regular spherical morphology with an average diameter of 96 µm and an LO encapsulation efficiency of 81 wt%. TGA confirmed their thermal stability up to 200 °C, while FTIR verified the successful encapsulation of LO. For performance evaluation, 10 wt% of the microcapsules was incorporated into an epoxy matrix and applied to carbon steel. Corrosion resistance was evaluated using electrochemical impedance spectroscopy (EIS) in 0.1 mol/L of NaCl solution over 500 h. The coating with microcapsules exhibited a |Z|0.01 of 106 Ω·cm2, higher than the 104 Ω·cm2 observed for the coating without microcapsules, indicating improved barrier properties. Raman spectroscopy confirmed the auto-oxidation of LO at damaged areas, evidencing the self-healing mechanism. Although full barrier recovery was not achieved, the system effectively delayed corrosion progression.
- Open Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 23 (2)
Metallurgical and Electrochemical characterization of a Supermartensitic Steel
The pitting corrosion of supermartensitic stainless steel (SMSS) was studied in an aqueous solution of 0.1 mol/L NaCl using the scanning vibrating electrode technique (SVET) and cyclic voltammetry. The SMSS showed 0.9% of retained austenite, as verified by Mössbauer spectroscopy. Cuboidal TiN particles were identified on the steel surfaces, by using optical, scanning electron, and transmission microscopy, associated to Mg-Ca-Al rich precipitates. Pit nucleation was slow and only verified after 24 h, associated to TiN/CaO•MgO•Al 2 O 3 complex inclusions, thus on original interdendritic spaces, where lower Cr content and the presence of inclusions are expected.
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 23 (2)
Open AccessMetallurgical and Electrochemical characterization of a Supermartensitic Steel
The pitting corrosion of supermartensitic stainless steel (SMSS) was studied in an aqueous solution of 0.1 mol/L NaCl using the scanning vibrating electrode technique (SVET) and cyclic voltammetry. The SMSS showed 0.9% of retained austenite, as verified by Mössbauer spectroscopy. Cuboidal TiN particles were identified on the steel surfaces, by using optical, scanning electron, and transmission microscopy, associated to Mg-Ca-Al rich precipitates. Pit nucleation was slow and only verified after 24 h, associated to TiN/CaO•MgO•Al 2 O 3 complex inclusions, thus on original interdendritic spaces, where lower Cr content and the presence of inclusions are expected.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Corrosion Behavior of 316L and Alloy 182 Dissimilar Weld Joint with Post-Weld Heat Treatment
Austenitic stainless steel and nickel-base alloys welds are widely used in nuclear reactor components, plants of energy generation, chemical, and petrochemical industries, due to their high corrosion resistance. The post weld heat treatments (PWHT) are generally applied to welding in order to relieve the welding residual stress. The aim of this work was to evaluate the influence of different PWHT on corrosion behavior of a dissimilar weld joint of two AISI 316L austenitic stainless steel plates with a nickel-base alloy as filler material in saline environments. The material was submitted to heat treatments for three hours at 600, 700 and 800 °C. The weld joint was examined by optical microscopy to determine the effects of PWHT in the microstructure. The corrosion behavior of the samples before and after heat treatment was evaluated using cyclic potentiodynamic polarization (CPP) in sodium chloride solutions (19% v/v) and pH 4.0 at room temperature. Metallographic analyses showed that delta ferrite dissolute as PWHT temperature increased. CPP curves demonstrated an increase of pitting corrosion resistance as the PWHT temperature rises, although the pit size has been increased. The heat treated weld joint at 600 °C showed a similar corrosion resistance compared to as-welded material.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Open AccessCorrosion Behavior of 316L and Alloy 182 Dissimilar Weld Joint with Post-Weld Heat Treatment
Austenitic stainless steel and nickel-base alloys welds are widely used in nuclear reactor components, plants of energy generation, chemical, and petrochemical industries, due to their high corrosion resistance. The post weld heat treatments (PWHT) are generally applied to welding in order to relieve the welding residual stress. The aim of this work was to evaluate the influence of different PWHT on corrosion behavior of a dissimilar weld joint of two AISI 316L austenitic stainless steel plates with a nickel-base alloy as filler material in saline environments. The material was submitted to heat treatments for three hours at 600, 700 and 800 °C. The weld joint was examined by optical microscopy to determine the effects of PWHT in the microstructure. The corrosion behavior of the samples before and after heat treatment was evaluated using cyclic potentiodynamic polarization (CPP) in sodium chloride solutions (19% v/v) and pH 4.0 at room temperature. Metallographic analyses showed that delta ferrite dissolute as PWHT temperature increased. CPP curves demonstrated an increase of pitting corrosion resistance as the PWHT temperature rises, although the pit size has been increased. The heat treated weld joint at 600 °C showed a similar corrosion resistance compared to as-welded material.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 24
Avaliação da Adição de Ti, Nb e (Ti+Nb) na Microestrutura e Susceptibilidade à Sensitização de Aços Inoxidáveis Ferríticos Submetidos à Soldagem TIG
Resumo Neste estudo, a microestrutura e a resistência à corrosão intergranular de aços inoxidáveis ferríticos com adições de Nb, Ti e (Ti+Nb) submetidos à soldagem TIG foram investigadas. A caracterização estrutural dos cordões de solda foi realizada através de microscopias óptica (MO) e eletrônica de varredura (MEV) e espectroscopia por energia dispersiva (EDS). A susceptibilidade à sensitização foi avaliada qualitativamente através da Prática W da norma ASTM 763 e quantitativamente através da técnica DL-EPR. Observou-se uma rede de martensita nos contornos de grão na região da solda do aço não estabilizado e uma microestrutura completamente ferrítica nas amostras dos aços com adições de estabilizantes. A Prática W revelou corrosão generalizada no interior dos grãos do aço AISI 430 e a presença de valas no AISI 430 Ti e concomitantemente com a técnica DL-EPR constatou-se que esses aços foram sensitizados pela soldagem. Já as amostras dos aços com adições de Nb e (Ti+Nb) mantiveram boa resistência à corrosão, estando livres de sensitização após a soldagem.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 24
Open AccessAvaliação da Adição de Ti, Nb e (Ti+Nb) na Microestrutura e Susceptibilidade à Sensitização de Aços Inoxidáveis Ferríticos Submetidos à Soldagem TIG
Resumo Neste estudo, a microestrutura e a resistência à corrosão intergranular de aços inoxidáveis ferríticos com adições de Nb, Ti e (Ti+Nb) submetidos à soldagem TIG foram investigadas. A caracterização estrutural dos cordões de solda foi realizada através de microscopias óptica (MO) e eletrônica de varredura (MEV) e espectroscopia por energia dispersiva (EDS). A susceptibilidade à sensitização foi avaliada qualitativamente através da Prática W da norma ASTM 763 e quantitativamente através da técnica DL-EPR. Observou-se uma rede de martensita nos contornos de grão na região da solda do aço não estabilizado e uma microestrutura completamente ferrítica nas amostras dos aços com adições de estabilizantes. A Prática W revelou corrosão generalizada no interior dos grãos do aço AISI 430 e a presença de valas no AISI 430 Ti e concomitantemente com a técnica DL-EPR constatou-se que esses aços foram sensitizados pela soldagem. Já as amostras dos aços com adições de Nb e (Ti+Nb) mantiveram boa resistência à corrosão, estando livres de sensitização após a soldagem.
- Open Access
- 1 December 2016
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 13 (13) , 2439-2450
Development and Test of an Equipment to Measure Residual Strain Inside Pipes Using the Hole-Drilling Method
Residual stresses are present in materials or structural component in the absence of external loads or changes in temperatures. The most common causes of residual stresses being present are the manufacturing or assembling processes. All manufacturing processes, such as casting, welding, machining, moulding, heat treatment, etc, introduces residual stresses into the manufactured object. The residual stresses effects could be beneficial or detrimental, depending on its distribution related to the component or structure, its load service and if they are compressive or tensile. In order to do the studies of residual stresses inside pipes, where the fatigue cracks normally initiate, an equipment that allows applying the Hole-Drilling Method was developed. The equipment efficacy was confirmed in this work by using it to detect residual strains inside a Mock-up that simulates the relief and security nozzle of Angra 1 Nuclear Power Plant (NPP) pressuriser.
- 1 December 2016
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 13 (13) , 2439-2450
Open AccessDevelopment and Test of an Equipment to Measure Residual Strain Inside Pipes Using the Hole-Drilling Method
Residual stresses are present in materials or structural component in the absence of external loads or changes in temperatures. The most common causes of residual stresses being present are the manufacturing or assembling processes. All manufacturing processes, such as casting, welding, machining, moulding, heat treatment, etc, introduces residual stresses into the manufactured object. The residual stresses effects could be beneficial or detrimental, depending on its distribution related to the component or structure, its load service and if they are compressive or tensile. In order to do the studies of residual stresses inside pipes, where the fatigue cracks normally initiate, an equipment that allows applying the Hole-Drilling Method was developed. The equipment efficacy was confirmed in this work by using it to detect residual strains inside a Mock-up that simulates the relief and security nozzle of Angra 1 Nuclear Power Plant (NPP) pressuriser.
- 1 January 2011
- Published by Taylor & Francis in Welding International
- Vol. 25 (1) , 15-23
Stress corrosion cracking of the AISI 316L stainless steel HAZ in a PWR nuclear reactor environment
Low-carbon alloy steels and stainless steels are widely used in the primary circuits of pressurized water reactor (PWR)-type nuclear reactors. Nickel alloys are employed in welding these materials due to their characteristics such as high mechanical and corrosion resistance and suitable thermal expansion coefficients. Over the last 30 years, stress corrosion cracking (SCC) has mainly been observed in the regions of welds between dissimilar materials that exist in these reactors. The objective of this work is to evaluate, for comparison purposes, the susceptibility to SCC of the heat-affected zone of austenitic stainless steel AISI 316L when subject to an environment that is similar to the primary circuit of a PWR nuclear reactor at temperatures of 303 and 325°C. To carry out this evaluation, the slow strain rate test was used. The results indicate that the SCC is heat activated and that at 325°C, the most significant weak fractures arising from SCC process can be seen.
- 1 January 2011
- Published by Taylor & Francis in Welding International
- Vol. 25 (1) , 15-23
Stress corrosion cracking of the AISI 316L stainless steel HAZ in a PWR nuclear reactor environment
Low-carbon alloy steels and stainless steels are widely used in the primary circuits of pressurized water reactor (PWR)-type nuclear reactors. Nickel alloys are employed in welding these materials due to their characteristics such as high mechanical and corrosion resistance and suitable thermal expansion coefficients. Over the last 30 years, stress corrosion cracking (SCC) has mainly been observed in the regions of welds between dissimilar materials that exist in these reactors. The objective of this work is to evaluate, for comparison purposes, the susceptibility to SCC of the heat-affected zone of austenitic stainless steel AISI 316L when subject to an environment that is similar to the primary circuit of a PWR nuclear reactor at temperatures of 303 and 325°C. To carry out this evaluation, the slow strain rate test was used. The results indicate that the SCC is heat activated and that at 325°C, the most significant weak fractures arising from SCC process can be seen.
- Open Access
- 1 September 2009
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 14 (3) , 228-237
Avaliação da suscetibilidade à corrosão sob tensão da ZAC do aço inoxidável AISI 316L em ambiente de reator nuclear PWR
Aços carbono de baixa liga e aços inoxidáveis são amplamente utilizados nos circuitos primários de reatores nucleares do tipo PWR (Pressurized Water Reactor). Ligas de níquel são empregadas na soldagem destes materiais devido a características como elevadas resistências mecânica e à corrosão, coeficiente de expansão térmica adequado, etc. Nos últimos 30 anos, a corrosão sob tensão (CST) tem sido observada principalmente nas regiões das soldas entre materiais dissimilares existentes nestes reatores. Este trabalho teve como objetivo avaliar, por comparação, a suscetibilidade à corrosão sob tensão da zona afetada pelo calor (ZAC) do aço inoxidável austenítico AISI 316L quando submetida a um ambiente similar ao do circuito primário de um reator nuclear PWR nas temperaturas de 303ºC e 325ºC. Para esta avaliação empregou-se o ensaio de taxa de deformação lenta - SSRT (Slow Strain Rate Test). Os resultados indicaram que a CST é ativada termicamente e que a 325ºC pode-se observar a presença mais significativa de fratura frágil decorrente do processo de corrosão sob tensão.
- 1 September 2009
- Published by FapUNIFESP (SciELO) in Soldagem & Inspeção
- Vol. 14 (3) , 228-237
Open AccessAvaliação da suscetibilidade à corrosão sob tensão da ZAC do aço inoxidável AISI 316L em ambiente de reator nuclear PWR
Aços carbono de baixa liga e aços inoxidáveis são amplamente utilizados nos circuitos primários de reatores nucleares do tipo PWR (Pressurized Water Reactor). Ligas de níquel são empregadas na soldagem destes materiais devido a características como elevadas resistências mecânica e à corrosão, coeficiente de expansão térmica adequado, etc. Nos últimos 30 anos, a corrosão sob tensão (CST) tem sido observada principalmente nas regiões das soldas entre materiais dissimilares existentes nestes reatores. Este trabalho teve como objetivo avaliar, por comparação, a suscetibilidade à corrosão sob tensão da zona afetada pelo calor (ZAC) do aço inoxidável austenítico AISI 316L quando submetida a um ambiente similar ao do circuito primário de um reator nuclear PWR nas temperaturas de 303ºC e 325ºC. Para esta avaliação empregou-se o ensaio de taxa de deformação lenta - SSRT (Slow Strain Rate Test). Os resultados indicaram que a CST é ativada termicamente e que a 325ºC pode-se observar a presença mais significativa de fratura frágil decorrente do processo de corrosão sob tensão.