Ara Bissal
Ara Bissal has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Martin März
Friedrich-Alexander-Universitt Erlangen-Nurnberg,Department of Electrical Engineering,Nuremberg,Germany
2 shared publications- Waqas Ali
Department of Electrical Engineering (RCET), University of Engineering and Technology, Lahore, PAKISTAN
2 shared publications - Anders Eriksson
KTH Mechanics, Royal Institute of Technology, Stockholm, Sweden
1 shared publication - Fermín Gómez de León
Department of Energy Galileo Ferraris (DENERG), Politecnico di Torino, 10129 Turin, Italy
1 shared publication - Göran Engdahl
Royal Institute of Technology Stockholm, Sweden
1 shared publication - Jesper Magnusson
Department of Electromagnetic Engineering, Royal Institute of Technology (KTH), Teknikringen 33, Stockholm SE-100 44, Sweden
1 shared publication
Latest Publications
- Open Access
- 14 May 2025
- Published by University of Maribor
- p. 141-146
A Novel Railgun Simulation Model Based on a Quasistatic
This paper presents a novel railgun simulation model based on a quasistatic study in COMSOL. Traditional analytical models are inaccurate as they use the coenergy principle to calculate the force on the armature, yielding the total force in the displacement axis. By using a numerical magnetic solution, a parametric analysis evaluates the flux linkage, armature force, and system resistance at various positions and currents. After characterizing the railgun, the transient problem is solved by coupling the parametric study results with the system's equivalent circuit. Finally, the results are compared with those from the analytical approach.
- 14 May 2025
- Published by University of Maribor
- p. 141-146
Open AccessA Novel Railgun Simulation Model Based on a Quasistatic
This paper presents a novel railgun simulation model based on a quasistatic study in COMSOL. Traditional analytical models are inaccurate as they use the coenergy principle to calculate the force on the armature, yielding the total force in the displacement axis. By using a numerical magnetic solution, a parametric analysis evaluates the flux linkage, armature force, and system resistance at various positions and currents. After characterizing the railgun, the transient problem is solved by coupling the parametric study results with the system's equivalent circuit. Finally, the results are compared with those from the analytical approach.
- 29 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1410-1416
Experimental Verification of a Hybrid DC Breaker’s Solid-State Branch, Utilizing Discrete IGBTs, for LVDC Systems
Hybrid direct current (DC) breakers are essential for fast fault current interruption in low voltage direct current (LVDC) systems. This study investigates the current interruption capabilities of a hybrid DC breaker’s solid-state branch by using a programmable flyback power supply to generate different gate voltages. The results demonstrate that a single discrete insulated gate bipolar transistor (IGBT) in a TO-264 package can interrupt 1300 A by increasing the gate voltage from 16 V to 30 V, 12 times its rated value. By connecting four of these IGBTs in parallel with a symmetric layout, equal current sharing is achieved, allowing currents up to 4000 A to be successfully interrupted. These findings pave the way for small, efficient, cost-effective hybrid DC breakers that do not require expensive IGBT modules.
- 29 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1410-1416
Experimental Verification of a Hybrid DC Breaker’s Solid-State Branch, Utilizing Discrete IGBTs, for LVDC Systems
Hybrid direct current (DC) breakers are essential for fast fault current interruption in low voltage direct current (LVDC) systems. This study investigates the current interruption capabilities of a hybrid DC breaker’s solid-state branch by using a programmable flyback power supply to generate different gate voltages. The results demonstrate that a single discrete insulated gate bipolar transistor (IGBT) in a TO-264 package can interrupt 1300 A by increasing the gate voltage from 16 V to 30 V, 12 times its rated value. By connecting four of these IGBTs in parallel with a symmetric layout, equal current sharing is achieved, allowing currents up to 4000 A to be successfully interrupted. These findings pave the way for small, efficient, cost-effective hybrid DC breakers that do not require expensive IGBT modules.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1201-1206
Influence of gate to emitter voltage on the IGBT fault current interruption capabilities in a hybrid DC breaker
Low voltage direct current (DC) systems are playing a pivotal role in the transformation of the grid especially to accommodate for increasing power demands. One of the key enabling technologies is an ultra-fast DC breaker. Although some research has been done on DC breakers, they are relatively large and expensive devices especially due to the semiconductor branch. In this paper, an insulated gate bipolar transistor (IGBT) in a TO-264 package was driven to its limit to study its fault current interruption capability at very high currents. A programmable flyback converter was designed and built to test the turn-off capability of the IGBT at different gate voltages and currents. It has been shown that increasing the gate voltage from 15 V to 30 V, and minimizing stray inductances, a single IGBT can conduct and turn-off currents as large as 1300 A , i.e., 12 times the rated value, thereby significantly reducing the hybrid DC breaker size and cost.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1201-1206
Influence of gate to emitter voltage on the IGBT fault current interruption capabilities in a hybrid DC breaker
Low voltage direct current (DC) systems are playing a pivotal role in the transformation of the grid especially to accommodate for increasing power demands. One of the key enabling technologies is an ultra-fast DC breaker. Although some research has been done on DC breakers, they are relatively large and expensive devices especially due to the semiconductor branch. In this paper, an insulated gate bipolar transistor (IGBT) in a TO-264 package was driven to its limit to study its fault current interruption capability at very high currents. A programmable flyback converter was designed and built to test the turn-off capability of the IGBT at different gate voltages and currents. It has been shown that increasing the gate voltage from 15 V to 30 V, and minimizing stray inductances, a single IGBT can conduct and turn-off currents as large as 1300 A , i.e., 12 times the rated value, thereby significantly reducing the hybrid DC breaker size and cost.
- Open Access
Hybrid Multi-Physics Modeling of an Ultra-Fast Electro-Mechanical Actuator
The challenges of an HVDC breaker are to generate impulsive forces in the order of hundreds of kilonewtons within fractions of a millisecond, to withstand the arising internal mechanical stresses and to transmit these forces via an electrically-insulating device to the contact system with minimum time delay. In this work, several models were developed with different levels of complexity, computation time and accuracy. Experiments were done with two mushroom-shaped armatures to validate the developed simulation models. It was concluded that although the electromagnetic force generation mechanism is highly sensitive to the mechanical response of the system, the developed first order hybrid model is able to predict the performance of the breaker with good accuracy.
Open AccessHybrid Multi-Physics Modeling of an Ultra-Fast Electro-Mechanical Actuator
The challenges of an HVDC breaker are to generate impulsive forces in the order of hundreds of kilonewtons within fractions of a millisecond, to withstand the arising internal mechanical stresses and to transmit these forces via an electrically-insulating device to the contact system with minimum time delay. In this work, several models were developed with different levels of complexity, computation time and accuracy. Experiments were done with two mushroom-shaped armatures to validate the developed simulation models. It was concluded that although the electromagnetic force generation mechanism is highly sensitive to the mechanical response of the system, the developed first order hybrid model is able to predict the performance of the breaker with good accuracy.