Pinar Okumus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pinar Okumus has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Cancan Yang
McMaster University
5 shared publications Mauricio Diaz Arancibia
4 shared publicationsMichael G. Oliva
Professor, Dept. of Civil and Environmental Engineering, Univ. of Wisconsin, Madison WI 53706
4 shared publications- Ravi Ranade
University at Buffalo, State University of New York
3 shared publications - Brandon E. Ross
Clemson University
2 shared publications - Hanmin Wang
Mott MacDonald, Portland, OR 97204, USA
2 shared publications
Latest Publications
- 31 July 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (11) , 321-334
Evaluation of Torsional Strength Design Expressions Using Experimentally Validated Numerical Analysis of Post-tensioned Girders
Post-tensioning is a popular method of reinforcing concrete in modern bridge construction, providing economical and efficient design solutions. For hollow members such as girders with box-shaped cross sections, post-tensioning ducts that pass through thin flanges or webs can interrupt shear flow along the perimeter of the cross section. The members can also be prone to torsion as a result of tensile stresses created by eccentric post-tensioning. Although the current AASHTO Load and Resistance Factor Design (LRFD) Bridge Design Specifications (BDS) addresses torsional strength, very few studies have evaluated the torsional design procedures for post-tensioned girders. This study aims to identify the influence of ducts and post-tensioning force on the torsional behavior of box-shaped girders post-tensioned with bonded or unbonded strands. Nonlinear finite-element models of girders under torsion are developed and validated using test data. Torsional strengths obtained from the analyses are compared with the ones from AASHTO LRFD BDS. The comparison indicates that the AASHTO predictions can be very conservative and have a significant scatter. The predictions were still conservative when the factor of AASHTO LRFD BDS that accounts for ducts for bonded strands was eliminated.
- 31 July 2025
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2679 (11) , 321-334
Evaluation of Torsional Strength Design Expressions Using Experimentally Validated Numerical Analysis of Post-tensioned Girders
Post-tensioning is a popular method of reinforcing concrete in modern bridge construction, providing economical and efficient design solutions. For hollow members such as girders with box-shaped cross sections, post-tensioning ducts that pass through thin flanges or webs can interrupt shear flow along the perimeter of the cross section. The members can also be prone to torsion as a result of tensile stresses created by eccentric post-tensioning. Although the current AASHTO Load and Resistance Factor Design (LRFD) Bridge Design Specifications (BDS) addresses torsional strength, very few studies have evaluated the torsional design procedures for post-tensioned girders. This study aims to identify the influence of ducts and post-tensioning force on the torsional behavior of box-shaped girders post-tensioned with bonded or unbonded strands. Nonlinear finite-element models of girders under torsion are developed and validated using test data. Torsional strengths obtained from the analyses are compared with the ones from AASHTO LRFD BDS. The comparison indicates that the AASHTO predictions can be very conservative and have a significant scatter. The predictions were still conservative when the factor of AASHTO LRFD BDS that accounts for ducts for bonded strands was eliminated.
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 30 (7)
Shear Condition Classification of Cracked Reinforced Concrete Beams Using Machine Learning
- 1 July 2025
- Published by American Society of Civil Engineers (ASCE) in Journal of Bridge Engineering
- Vol. 30 (7)
Shear Condition Classification of Cracked Reinforced Concrete Beams Using Machine Learning
- 12 September 2024
- Published by Springer Nature
- p. 451-458
Development of 3D Printable Strain Hardening Cementitious Composites for Bridge-Related Applications
- 12 September 2024
- Published by Springer Nature
- p. 451-458
Development of 3D Printable Strain Hardening Cementitious Composites for Bridge-Related Applications
- 12 April 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (8) , 2577-2591
Lateral load response and collapse probability of reinforced concrete shear walls retrofitted for repairability
This paper demonstrates the efficacy of a new reinforced concrete shear wall seismic retrofit method through a series of nonlinear static and incremental dynamic analyses. Unlike traditional retrofit methods, the method investigated aims to convert conventional walls into self‐centering walls whose behavior is governed by rocking and flexure. The retrofit involves creating a cold joint at the foundation–wall interface, cutting some reinforcing bars to allow rocking, adding external post‐tensioning to enable self‐centering, and externally confining wall toes to prevent concrete crushing. The retrofit was applied to two building archetypes, each with two different shear wall designs. The four walls were retrofitted by varying retrofit parameters (portion of the vertical reinforcement bars cut, and external post‐tensioning amount). Nonlinear static and nonlinear response history analyses were performed using experimentally validated, computationally efficient models that simulate walls with fiber‐based beam–column elements. Incremental dynamic analysis was used to create collapse fragility functions for pre‐ and post‐retrofit walls. The results show that the retrofit is effective when some vertical reinforcement bars are left uncut across the foundation–wall interface. The retrofit is more effective for walls with vertical reinforcement distributed across cross‐section as compared to walls with reinforcement concentrated near boundary elements and for walls with structurally efficient amounts of reinforcement as compared to walls with higher amounts of reinforcement. This is attributed to the larger amount of reinforcement bars cut in walls with concentrated reinforcement layouts or heavy reinforcement amounts, leading to a larger loss of strength, recovery of which requires larger amounts of post‐tensioning.
- 12 April 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 53 (8) , 2577-2591
Lateral load response and collapse probability of reinforced concrete shear walls retrofitted for repairability
This paper demonstrates the efficacy of a new reinforced concrete shear wall seismic retrofit method through a series of nonlinear static and incremental dynamic analyses. Unlike traditional retrofit methods, the method investigated aims to convert conventional walls into self‐centering walls whose behavior is governed by rocking and flexure. The retrofit involves creating a cold joint at the foundation–wall interface, cutting some reinforcing bars to allow rocking, adding external post‐tensioning to enable self‐centering, and externally confining wall toes to prevent concrete crushing. The retrofit was applied to two building archetypes, each with two different shear wall designs. The four walls were retrofitted by varying retrofit parameters (portion of the vertical reinforcement bars cut, and external post‐tensioning amount). Nonlinear static and nonlinear response history analyses were performed using experimentally validated, computationally efficient models that simulate walls with fiber‐based beam–column elements. Incremental dynamic analysis was used to create collapse fragility functions for pre‐ and post‐retrofit walls. The results show that the retrofit is effective when some vertical reinforcement bars are left uncut across the foundation–wall interface. The retrofit is more effective for walls with vertical reinforcement distributed across cross‐section as compared to walls with reinforcement concentrated near boundary elements and for walls with structurally efficient amounts of reinforcement as compared to walls with higher amounts of reinforcement. This is attributed to the larger amount of reinforcement bars cut in walls with concentrated reinforcement layouts or heavy reinforcement amounts, leading to a larger loss of strength, recovery of which requires larger amounts of post‐tensioning.
- 6 September 2023
- Published by Elsevier in Engineering Structures
- Vol. 295
Live load and long-term response of steel bridges with high skew
- 6 September 2023
- Published by Elsevier in Engineering Structures
- Vol. 295
Live load and long-term response of steel bridges with high skew
- 3 June 2023
- Published by Springer Nature
- p. 622-633
Post-tensioning Force Measurement Using Optical Fiber Sensor-Embedded Strand for Prestressed Concrete Structures
- 3 June 2023
- Published by Springer Nature
- p. 622-633
Post-tensioning Force Measurement Using Optical Fiber Sensor-Embedded Strand for Prestressed Concrete Structures
- Open Access
- 22 March 2023
- Published by Elsevier in Resilient Cities and Structures
- Vol. 2 (1) , 152-161
Behavior and modeling of tessellated shear walls in a structural frame system
- 22 March 2023
- Published by Elsevier in Resilient Cities and Structures
- Vol. 2 (1) , 152-161
Open AccessBehavior and modeling of tessellated shear walls in a structural frame system
- 1 April 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 46
Finite element modeling of tessellated beams
- 1 April 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 46
Finite element modeling of tessellated beams
- 22 March 2022
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 19 (11) , 1676-1686
Estimating chloride exposure of reinforced concrete bridges using vehicle spray and splash mechanisms
Reinforced concrete (RC) bridges located in cold climates are typically exposed to large amounts of deicing salts during winter, which causes corrosion-related deterioration of RC bridges. Vehicle spray and splash are the major mechanisms of transporting deicing salts from the road to the exterior bridge surfaces. However, a systematic method for incorporating these mechanisms in the estimation of chloride exposure of an RC bridge is not available in the literature. This article aims to fill this knowledge gap. An analytical method is proposed to estimate the surface chloride concentration for an RC bridge, considering snow precipitation, salt application, vehicle type, vehicle speed, traffic volume, and distance to the roadside. The proposed method is demonstrated using an example RC bridge, and the results are compared with reported data from field tests. A parametric study investigating the effects of various model parameters on the results is also included in this article. The proposed method is expected to improve the determination of corrosion initiation time in service life estimation models for RC bridges.
- 22 March 2022
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 19 (11) , 1676-1686
Estimating chloride exposure of reinforced concrete bridges using vehicle spray and splash mechanisms
Reinforced concrete (RC) bridges located in cold climates are typically exposed to large amounts of deicing salts during winter, which causes corrosion-related deterioration of RC bridges. Vehicle spray and splash are the major mechanisms of transporting deicing salts from the road to the exterior bridge surfaces. However, a systematic method for incorporating these mechanisms in the estimation of chloride exposure of an RC bridge is not available in the literature. This article aims to fill this knowledge gap. An analytical method is proposed to estimate the surface chloride concentration for an RC bridge, considering snow precipitation, salt application, vehicle type, vehicle speed, traffic volume, and distance to the roadside. The proposed method is demonstrated using an example RC bridge, and the results are compared with reported data from field tests. A parametric study investigating the effects of various model parameters on the results is also included in this article. The proposed method is expected to improve the determination of corrosion initiation time in service life estimation models for RC bridges.
- 10 September 2021
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 19 (5) , 708-730
Seismic fragility of reinforced concrete bridge columns utilizing ductile fiber-reinforced concrete covers
The seismic resistance of reinforced concrete (RC) bridge piers reduces over time due to gradual deterioration processes, such as reinforcement corrosion. Using a ductile fiber reinforced concrete (FRC) reinforcement cover may mitigate deterioration. However, current methodologies for estimating deterioration and capacity reduction cannot be applied to bridge piers with cover made of a ductile FRC that behaves differently from conventional concrete. This article utilizes a systematic framework that combines corrosion and seismic analyses to address this limitation. The seismic fragility of an example bridge column with a ductile FRC cover was estimated using the framework and compared to that of a column with a conventional concrete cover. A detailed pitting corrosion model, which explicitly accounted for differences in cover crack patterns of concrete and a ductile FRC, was developed to estimate the rebar mass loss as a function of time. Seismic fragility functions were constructed by nonlinear response history analyses, incorporating rebar mass loss, at discrete times during the life span of the bridge. The results indicate that improved durability of the RC bridge pier enabled by FRC cover translates into a lower probability of seismic damage over time compared to the pier with a conventional concrete cover.
- 10 September 2021
- Published by Taylor & Francis in Structure and Infrastructure Engineering
- Vol. 19 (5) , 708-730
Seismic fragility of reinforced concrete bridge columns utilizing ductile fiber-reinforced concrete covers
The seismic resistance of reinforced concrete (RC) bridge piers reduces over time due to gradual deterioration processes, such as reinforcement corrosion. Using a ductile fiber reinforced concrete (FRC) reinforcement cover may mitigate deterioration. However, current methodologies for estimating deterioration and capacity reduction cannot be applied to bridge piers with cover made of a ductile FRC that behaves differently from conventional concrete. This article utilizes a systematic framework that combines corrosion and seismic analyses to address this limitation. The seismic fragility of an example bridge column with a ductile FRC cover was estimated using the framework and compared to that of a column with a conventional concrete cover. A detailed pitting corrosion model, which explicitly accounted for differences in cover crack patterns of concrete and a ductile FRC, was developed to estimate the rebar mass loss as a function of time. Seismic fragility functions were constructed by nonlinear response history analyses, incorporating rebar mass loss, at discrete times during the life span of the bridge. The results indicate that improved durability of the RC bridge pier enabled by FRC cover translates into a lower probability of seismic damage over time compared to the pier with a conventional concrete cover.