Zhiyong Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhiyong Shi has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Enrico Meli
Department of Industrial Engineering, University of Florence, 50139 Florence, Italy
6 shared publications - Andrea Rindi
Department of Industrial Engineering, University of Florence, 50139 Florence, Italy
4 shared publications Andrea Rindi
3 shared publications- Kaiyun Wang
Southwest Jiaotong University
3 shared publications - Binjie Xu
State Key Laboratory of Rail Transit Vehicle System, Southwest Jiaotong University, Chengdu, China
2 shared publications Enrico Meli
2 shared publications
Latest Publications
- 1 June 2026
- Published by Elsevier in Engineering Failure Analysis
- Vol. 196
Failure mechanism of hunting stability degradation in high-speed trains under crosswind conditions
- 1 June 2026
- Published by Elsevier in Engineering Failure Analysis
- Vol. 196
Failure mechanism of hunting stability degradation in high-speed trains under crosswind conditions
- 28 July 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 181
Influence of profile optimization on wear and fatigue characteristics of curved rail: An experimental study
- 28 July 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 181
Influence of profile optimization on wear and fatigue characteristics of curved rail: An experimental study
- 5 May 2025
- Published by Elsevier in Tribology International
- Vol. 210
Interactive damage behaviors between rail corrosion and rolling contact in the marine atmospheric environment
- 5 May 2025
- Published by Elsevier in Tribology International
- Vol. 210
Interactive damage behaviors between rail corrosion and rolling contact in the marine atmospheric environment
- 18 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 406-420
Optimization design of curved rail profile for heavy-haul railways based on multi-period optimization method
Rail grinding is widely employed in heavy-haul railways to mitigate abnormal rail wear. However, frequent grinding can result in even more significant material loss than regular wear. This paper presents a method for adjusting track layout parameters to alleviate the severe rail wear problem on curved lines. First, field experiments and simulation analysis have been used to analyze the impact of track parameters on wheel-rail contact and the feasibility of parameter adjustment. A numerical optimization model has been established based on Genetic Algorithm-Levenberg Marquardt- Backpropagation neural networks (GA-LM-BP neural network), with the track parameters as the independent variable and the goal of reducing wear as the objective. The chaotic microvariation adaptive genetic algorithm has been used to obtain an optimized solution set. Finally, the optimization effects are revealed by comparing the rail wear characteristics obtained from the original values and the optimal solution set.
- 18 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 406-420
Optimization design of curved rail profile for heavy-haul railways based on multi-period optimization method
Rail grinding is widely employed in heavy-haul railways to mitigate abnormal rail wear. However, frequent grinding can result in even more significant material loss than regular wear. This paper presents a method for adjusting track layout parameters to alleviate the severe rail wear problem on curved lines. First, field experiments and simulation analysis have been used to analyze the impact of track parameters on wheel-rail contact and the feasibility of parameter adjustment. A numerical optimization model has been established based on Genetic Algorithm-Levenberg Marquardt- Backpropagation neural networks (GA-LM-BP neural network), with the track parameters as the independent variable and the goal of reducing wear as the objective. The chaotic microvariation adaptive genetic algorithm has been used to obtain an optimized solution set. Finally, the optimization effects are revealed by comparing the rail wear characteristics obtained from the original values and the optimal solution set.
- 12 July 2023
- Published by Elsevier in Measurement
- Vol. 219
Measurement of vehicle speed based on the GCC algorithm and its application in anti-slip control
- 12 July 2023
- Published by Elsevier in Measurement
- Vol. 219
Measurement of vehicle speed based on the GCC algorithm and its application in anti-slip control
- 10 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 237 (6) , 693-703
A degraded adhesion model for creep force calculation based on the CONTACT algorithm
Degraded adhesion is observed extensively during the braking or traction process. An accurate degraded adhesion law, on the other hand, is difficult to acquire since it is characterized by a complicated non-linear behaviour involving various surface phenomena. This work provides a new local degraded adhesion model, its implementation in a wheel-rail contact model, and its application in a multibody railway vehicle model. The present degraded adhesion model takes into account large sliding and adhesion recovery phenomena, which are strictly related to the power dissipated at the contact interface. Implementation of the current local degraded adhesion model enhances Kalker’s CONTACT algorithm. The application into multibody dynamics simulation demonstrates the high accuracy of computations. The model is validated by comparing it to experimental findings obtained from on-field tests. Simulated results regarding the tangential pressures, the slip velocity, and the dissipated power under degraded adhesion and partial adherence conditions are reported.
- 10 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 237 (6) , 693-703
A degraded adhesion model for creep force calculation based on the CONTACT algorithm
Degraded adhesion is observed extensively during the braking or traction process. An accurate degraded adhesion law, on the other hand, is difficult to acquire since it is characterized by a complicated non-linear behaviour involving various surface phenomena. This work provides a new local degraded adhesion model, its implementation in a wheel-rail contact model, and its application in a multibody railway vehicle model. The present degraded adhesion model takes into account large sliding and adhesion recovery phenomena, which are strictly related to the power dissipated at the contact interface. Implementation of the current local degraded adhesion model enhances Kalker’s CONTACT algorithm. The application into multibody dynamics simulation demonstrates the high accuracy of computations. The model is validated by comparing it to experimental findings obtained from on-field tests. Simulated results regarding the tangential pressures, the slip velocity, and the dissipated power under degraded adhesion and partial adherence conditions are reported.
- 23 March 2021
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 60 (7) , 2436-2450
Comparison of friction draft gear models for simulation in longitudinal train dynamics
The friction draft gear with hysteresis characteristics is one of the typical nonlinear elements in longitudinal train dynamics (LTD). Due to the nonlinear hysteresis of friction damping, the discontinuity between loading and unloading envelopes becomes a mathematical integration issue when adopting look-up table methods to establish draft gear models. It might cause integration divergence and wrong results if ignored. To solve this discontinuity, three different transitional strategies (velocity-dependent, intermediate slope, and smoothing approximation) are applied to building draft gear models, and the one-dimensional (1D) longitudinal train model adopting the ‘Zhai’ integration method is used. To ensure accurate results, the international benchmark cases of LTD are studied, and three draft gear models with different transitional strategies are compared in this paper. The results show that these three models can successfully work with ‘Zhai’ method in the LTD simulation to achieve the force agreement with benchmark cases. Compared to the other two models, the velocity-dependent model doesn’t exhibit good buffer deflection agreement and requires a smaller step size to achieve convergent results. Therefore, it is recommended that adopting the intermediate slope method or smoothing approximation approach avoids discontinuity problems of modelling draft gears in LTD.
- 23 March 2021
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 60 (7) , 2436-2450
Comparison of friction draft gear models for simulation in longitudinal train dynamics
The friction draft gear with hysteresis characteristics is one of the typical nonlinear elements in longitudinal train dynamics (LTD). Due to the nonlinear hysteresis of friction damping, the discontinuity between loading and unloading envelopes becomes a mathematical integration issue when adopting look-up table methods to establish draft gear models. It might cause integration divergence and wrong results if ignored. To solve this discontinuity, three different transitional strategies (velocity-dependent, intermediate slope, and smoothing approximation) are applied to building draft gear models, and the one-dimensional (1D) longitudinal train model adopting the ‘Zhai’ integration method is used. To ensure accurate results, the international benchmark cases of LTD are studied, and three draft gear models with different transitional strategies are compared in this paper. The results show that these three models can successfully work with ‘Zhai’ method in the LTD simulation to achieve the force agreement with benchmark cases. Compared to the other two models, the velocity-dependent model doesn’t exhibit good buffer deflection agreement and requires a smaller step size to achieve convergent results. Therefore, it is recommended that adopting the intermediate slope method or smoothing approximation approach avoids discontinuity problems of modelling draft gears in LTD.