Ben Thomas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ben Thomas has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Mark Hadfield
Bournemouth University
9 shared publications S. Austen
6 shared publications- Mayank Anand
Department of Design and Engineering,Bournemouth University, Poole BH12 5BB,UK
3 shared publications - Abu Saifullah
University of Portsmouth
2 shared publications - Antolin Hernández Battez
Department of Construction and Manufacturing Engineering, University of Oviedo, Pedro Puig Adam, s/n, 33203 Gijón, Spain
2 shared publications J. Gillman
The Balmain Environmental Trust Shaftesbury, United Kingdom
2 shared publications
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2607 (1) , 100005
An analysis of rotationally moulded sandwich structure’s repeated impact properties
Repeated impact properties of fully recyclable rotationally moulded polyethylene (PE) sandwich samples were experimentally investigated in this work. Testing was carried out with an impact force sensor attached drop weight impactor at 20 J to 50 J energy levels. These sandwich structures used in marine, automotive, large tanks and other applications, are susceptible to small damage due to impact events with floating debris, collisions or friction with other vehicles, crafts etc. in their service life which can grow with time and repeated impacts leading to a catastrophic failure. To avoid this unexpected situation, an in-depth understanding of repeated impact properties of this sandwich structure is essential. The repeated impact properties were analysed in terms of impact force-deflection, maximum impact force, impact damage and the total number of repeated impacts needed for sample penetration. A lower impact energy level showed a higher total repeated impact events to penetrate sandwich samples fully. The maximum impact force vs the repeated impact number figure exhibited three different regions which are related to the damage mechanisms of tested rotationally moulded sandwich samples.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2607 (1) , 100005
Open AccessAn analysis of rotationally moulded sandwich structure’s repeated impact properties
Repeated impact properties of fully recyclable rotationally moulded polyethylene (PE) sandwich samples were experimentally investigated in this work. Testing was carried out with an impact force sensor attached drop weight impactor at 20 J to 50 J energy levels. These sandwich structures used in marine, automotive, large tanks and other applications, are susceptible to small damage due to impact events with floating debris, collisions or friction with other vehicles, crafts etc. in their service life which can grow with time and repeated impacts leading to a catastrophic failure. To avoid this unexpected situation, an in-depth understanding of repeated impact properties of this sandwich structure is essential. The repeated impact properties were analysed in terms of impact force-deflection, maximum impact force, impact damage and the total number of repeated impacts needed for sample penetration. A lower impact energy level showed a higher total repeated impact events to penetrate sandwich samples fully. The maximum impact force vs the repeated impact number figure exhibited three different regions which are related to the damage mechanisms of tested rotationally moulded sandwich samples.
- Open Access
- 24 February 2017
- Published by Wiley in Polymer Engineering & Science
- Vol. 58 (1) , 63-73
Fracture toughness of rotationally molded polyethylene and polypropylene
In this work, the fracture toughness of rotationally molded polyethylene (PE) and polypropylene (PP) was measured using J integral methods at static loading rates and at room temperature. Two different commercially available rotational molding grades PE and PP were tested in this study which have been used in various rotationally molded products such as small leisure craft, water storage tanks, and so on. Scanning electron microscope (SEM), optical microscope, differential scanning calorimetry (DSC), solid‐state nuclear magnetic resonance (solid‐state NMR), and X‐ray scattering were used to investigate the microstructure, fracture surfaces, and compare toughness properties of these materials. In PE, higher molecular weight and broader molecular weight distribution, larger amorphous and crystal region thicknesses are found to be related to higher toughness values. High molecular weight favors higher number of entanglements that improve fracture energy and broader distribution increases long chain branching of higher molecular weight fractions which creates higher entanglements at the branch sites. Larger amorphous regions promote microvoiding more easily compared to thinner amorphous regions, leading to greater plastic deformation and energy absorption. Higher crystal thickness also contributes to microvoiding in the amorphous region. For PP, greater plastic deformation observed in the fracture surfaces is related to higher fracture toughness values. POLYM. ENG. SCI., 58:63–73, 2018. © 2017 Society of Plastics Engineers
- 24 February 2017
- Published by Wiley in Polymer Engineering & Science
- Vol. 58 (1) , 63-73
Open AccessFracture toughness of rotationally molded polyethylene and polypropylene
In this work, the fracture toughness of rotationally molded polyethylene (PE) and polypropylene (PP) was measured using J integral methods at static loading rates and at room temperature. Two different commercially available rotational molding grades PE and PP were tested in this study which have been used in various rotationally molded products such as small leisure craft, water storage tanks, and so on. Scanning electron microscope (SEM), optical microscope, differential scanning calorimetry (DSC), solid‐state nuclear magnetic resonance (solid‐state NMR), and X‐ray scattering were used to investigate the microstructure, fracture surfaces, and compare toughness properties of these materials. In PE, higher molecular weight and broader molecular weight distribution, larger amorphous and crystal region thicknesses are found to be related to higher toughness values. High molecular weight favors higher number of entanglements that improve fracture energy and broader distribution increases long chain branching of higher molecular weight fractions which creates higher entanglements at the branch sites. Larger amorphous regions promote microvoiding more easily compared to thinner amorphous regions, leading to greater plastic deformation and energy absorption. Higher crystal thickness also contributes to microvoiding in the amorphous region. For PP, greater plastic deformation observed in the fracture surfaces is related to higher fracture toughness values. POLYM. ENG. SCI., 58:63–73, 2018. © 2017 Society of Plastics Engineers
- Open Access
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
The potential of the water hammer in pico-scale tidal power systems: An experimental investigation
The tidal energy within the seas surrounding the United Kingdom offers a vast renewable resource that is perfectly predictable over long timescales. Currently, the bulk of tidal energy research is focused on developing large devices for the most resource rich locations, which can be many miles from populated areas. The potential of small-scale tidal power from sub-optimal shallow water sites, close to populated regions, has so far been overlooked. Such generation would benefit from reduced transmission losses and contribute towards a distributed electricity grid, helping to overcome the variability of other renewables. This work presents a novel method for generating hydropower using the water hammer effect: a pressure surge that can occur in a pipeline following the abrupt closure of a valve. These pressure surges are used to produce vertical oscillations from horizontally flowing water, allowing power to be generated in a manner analogous to a wave energy convertor. A non-optimised scale model was found experimentally to have a peak available power density of 1.08 ± 0.25 kW/m2 and a mean of 0.07 ± 0.02 kW/m2. In comparison, the MCT SeaGen S (arguably the most well-developed tidal energy device) is capable of generating 3.18 kW/m2. With further development, a water hammer device may therefore be useful for generating pico-scale tidal power in slow, shallow water flows.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Open AccessThe potential of the water hammer in pico-scale tidal power systems: An experimental investigation
The tidal energy within the seas surrounding the United Kingdom offers a vast renewable resource that is perfectly predictable over long timescales. Currently, the bulk of tidal energy research is focused on developing large devices for the most resource rich locations, which can be many miles from populated areas. The potential of small-scale tidal power from sub-optimal shallow water sites, close to populated regions, has so far been overlooked. Such generation would benefit from reduced transmission losses and contribute towards a distributed electricity grid, helping to overcome the variability of other renewables. This work presents a novel method for generating hydropower using the water hammer effect: a pressure surge that can occur in a pipeline following the abrupt closure of a valve. These pressure surges are used to produce vertical oscillations from horizontally flowing water, allowing power to be generated in a manner analogous to a wave energy convertor. A non-optimised scale model was found experimentally to have a peak available power density of 1.08 ± 0.25 kW/m2 and a mean of 0.07 ± 0.02 kW/m2. In comparison, the MCT SeaGen S (arguably the most well-developed tidal energy device) is capable of generating 3.18 kW/m2. With further development, a water hammer device may therefore be useful for generating pico-scale tidal power in slow, shallow water flows.
- Open Access
- 19 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 231 (1-2) , 162-170
The depletion of ZDDP additives within marine lubricants and associated cylinder liner wear in RNLI lifeboat engines
Previous work of authors indicated the wear of cylinder liners in marine engines of RNLI lifeboats due to the intense lubricant degradation identified by inductively coupled plasma and Fourier Transform Infrared spectroscopy techniques. In this paper, further analysis carried out to evaluate the effects of lubricant degradation on the actual cylinder liners installed in the Trent Class Lifeboat engines is presented. Surface characterisation of actual cylinder liner’s bore surface showed maximum wear near the top dead centre region compared to rest of the piston stroke. Wear in this region of the cylinder liner surface is controlled primarily by the protective film forming anti-wear additives in the lubricant which limit the direct surface contact between the piston rings and cylinder liner. The condition of zinc dialkyldithiophosphates anti-wear additives was analysed using the nuclear magnetic resonance spectroscopy. Tribology analysis was conducted to evaluate the tribological and boundary film forming performance of zinc dialkyldithiophosphates additives by simulating cylinder liner–piston ring contact near the top dead centre. To further understand the wear mechanisms of the cylinder liner, wear debris analysis (Analytical Ferrography) of lubricant samples was performed. Results revealed the depletion of phosphorus containing zinc dialkyldithiophosphates anti-wear additives as a function of the lubricant’s duty cycle within the marine engines and its effect on the tribological and boundary film forming performance of lubricants. Wear debris analysis showed the generation of ferrous debris potentially from the cylinder liners as a result of reduced anti-wear protection from the depleted zinc dialkyldithiophosphates additives during the tribological contact with piston rings and piston skirt region. These findings are useful to understand the lubricant degradation mechanisms which affect the functionality of cylinder liners, therefore allowing to plan the engine maintenance strategies.
- 19 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 231 (1-2) , 162-170
Open AccessThe depletion of ZDDP additives within marine lubricants and associated cylinder liner wear in RNLI lifeboat engines
Previous work of authors indicated the wear of cylinder liners in marine engines of RNLI lifeboats due to the intense lubricant degradation identified by inductively coupled plasma and Fourier Transform Infrared spectroscopy techniques. In this paper, further analysis carried out to evaluate the effects of lubricant degradation on the actual cylinder liners installed in the Trent Class Lifeboat engines is presented. Surface characterisation of actual cylinder liner’s bore surface showed maximum wear near the top dead centre region compared to rest of the piston stroke. Wear in this region of the cylinder liner surface is controlled primarily by the protective film forming anti-wear additives in the lubricant which limit the direct surface contact between the piston rings and cylinder liner. The condition of zinc dialkyldithiophosphates anti-wear additives was analysed using the nuclear magnetic resonance spectroscopy. Tribology analysis was conducted to evaluate the tribological and boundary film forming performance of zinc dialkyldithiophosphates additives by simulating cylinder liner–piston ring contact near the top dead centre. To further understand the wear mechanisms of the cylinder liner, wear debris analysis (Analytical Ferrography) of lubricant samples was performed. Results revealed the depletion of phosphorus containing zinc dialkyldithiophosphates anti-wear additives as a function of the lubricant’s duty cycle within the marine engines and its effect on the tribological and boundary film forming performance of lubricants. Wear debris analysis showed the generation of ferrous debris potentially from the cylinder liners as a result of reduced anti-wear protection from the depleted zinc dialkyldithiophosphates additives during the tribological contact with piston rings and piston skirt region. These findings are useful to understand the lubricant degradation mechanisms which affect the functionality of cylinder liners, therefore allowing to plan the engine maintenance strategies.
- Open Access
- 30 May 2016
- Published by MDPI AG in Lubricants
- Vol. 4 (2) , 17
Assessing Boundary Film Forming Behavior of Phosphonium Ionic Liquids as Engine Lubricant Additives
The reduction of friction and wear losses in boundary lubrication regime of a piston ring-cylinder liner tribo-system has always been a challenge for engine and lubricant manufacturers. One way is to use lubricant additives, which can form boundary film quickly and reduce the direct contact between asperities. This article focuses on the assessment of boundary film forming behavior of two phosphonium-based ionic liquids (ILs) as additives in engine-aged lubricant to further improve its film forming capabilities and hence reduce friction and wear of contacting surfaces. A reciprocating piston ring segment-on-flat coupon under fully flooded lubrication conditions at room temperature (approx. 25 °C) was employed. The trihexyltetradecyl phosphonium bis(2-ethylhexyl) phosphate and trihexyltetradecyl phosphonium bis(2,4,4-tri-methylpentyl) phosphinate ionic liquids were used as additives in 6 vol. % quantity. Benchmark tests were conducted using fully formulated new lubricant of same grade (with and without ILs). Results revealed that the addition of phosphonium ILs to engine-aged lubricant led to quicker initiation of boundary film forming process. In addition, friction and wear performance of engine-aged lubricant improved by the addition of both ILs and these mixtures outperformed the fresh fully formulated oil. Chemical analysis showed higher concentration of phosphorus element on the worn surface indicating presence of ILs in the formed tribofilms.
- 30 May 2016
- Published by MDPI AG in Lubricants
- Vol. 4 (2) , 17
Open AccessAssessing Boundary Film Forming Behavior of Phosphonium Ionic Liquids as Engine Lubricant Additives
The reduction of friction and wear losses in boundary lubrication regime of a piston ring-cylinder liner tribo-system has always been a challenge for engine and lubricant manufacturers. One way is to use lubricant additives, which can form boundary film quickly and reduce the direct contact between asperities. This article focuses on the assessment of boundary film forming behavior of two phosphonium-based ionic liquids (ILs) as additives in engine-aged lubricant to further improve its film forming capabilities and hence reduce friction and wear of contacting surfaces. A reciprocating piston ring segment-on-flat coupon under fully flooded lubrication conditions at room temperature (approx. 25 °C) was employed. The trihexyltetradecyl phosphonium bis(2-ethylhexyl) phosphate and trihexyltetradecyl phosphonium bis(2,4,4-tri-methylpentyl) phosphinate ionic liquids were used as additives in 6 vol. % quantity. Benchmark tests were conducted using fully formulated new lubricant of same grade (with and without ILs). Results revealed that the addition of phosphonium ILs to engine-aged lubricant led to quicker initiation of boundary film forming process. In addition, friction and wear performance of engine-aged lubricant improved by the addition of both ILs and these mixtures outperformed the fresh fully formulated oil. Chemical analysis showed higher concentration of phosphorus element on the worn surface indicating presence of ILs in the formed tribofilms.
- Open Access
- 18 March 2016
- Published by Springer Nature in Journal of Ocean Engineering and Marine Energy
- Vol. 2 (2) , 227-245
Current tidal power technologies and their suitability for applications in coastal and marine areas
- 18 March 2016
- Published by Springer Nature in Journal of Ocean Engineering and Marine Energy
- Vol. 2 (2) , 227-245
Open AccessCurrent tidal power technologies and their suitability for applications in coastal and marine areas
- 3 September 2012
- Published by WITPRESS LTD.
- Vol. 76, 99-111
Potential application of recycled plastic materials as a replacement for polyurethane wheels
- 3 September 2012
- Published by WITPRESS LTD.
- Vol. 76, 99-111
Potential application of recycled plastic materials as a replacement for polyurethane wheels
- Open Access
- 1 August 2012
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 16 (6) , 4126-4140
Future perspectives on sustainable tribology
- 1 August 2012
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 16 (6) , 4126-4140
Open AccessFuture perspectives on sustainable tribology
- 16 July 2010
- Published by Taylor & Francis in Tribology Transactions
- Vol. 53 (4) , 584-599
Wear and Friction Modeling on Lifeboat Launch Systems
- 16 July 2010
- Published by Taylor & Francis in Tribology Transactions
- Vol. 53 (4) , 584-599
Wear and Friction Modeling on Lifeboat Launch Systems