Anthony G. Fowler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Anthony G. Fowler has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- S. O. Reza Moheimani
Department of Systems Engineering, The University of Texas at Dallas, Richardson, TX, USA
2 shared publications - Hamed Alemansour
Erik Jonsson School of Engineering and Computer Science, The University of Texas at Dallas 1 , Richardson, Texas 75080
1 shared publication - Mohammad Maroufi
Department of Mechanical Engineering, University of Texas at Dallas, Richardson, TX, USA
1 shared publication - Mustafa Bulut Coskun
Department of Mechanical and Aerospace Engineering, Monash University, Melbourne, VIC/Australia
1 shared publication
Latest Publications
- 12 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 27 (5) , 2271-2278
$Q$ Control of an Active AFM Cantilever With Differential Sensing Configuration
Microcantilevers featuring separate built-in actuation and displacement sensing capabilities allow effective and simple implementation of control methods, opening a pathway to achieving higher scan speeds in tapping-mode atomic force microscopy. Such active cantilevers are a significant milestone to eventually obtain video-rate on-chip atomic force microscopes (AFMs) that can even surpass the functionality and imaging speed of their macroscale counterparts at a significantly lower cost. In this brief, we present an active AFM cantilever with an on-chip actuator and two built-in displacement sensors, designed to be integrated into on-chip AFMs. The common feedthrough problem present in this type of architecture is addressed by a differential sensing configuration, and the revealed dynamics are used for the system identification. A positive position feedback controller is designed to actively tailor the Q factor of the cantilever. The imaging performance of the microcantilever with and without Q control is compared by attenuating the cantilever's Q factor from 177 to 15 using the feedback loop. A common artifact in high-speed scans, the parachuting effect, is mitigated, rendering higher imaging speeds achievable.
- 12 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 27 (5) , 2271-2278
$Q$ Control of an Active AFM Cantilever With Differential Sensing Configuration
Microcantilevers featuring separate built-in actuation and displacement sensing capabilities allow effective and simple implementation of control methods, opening a pathway to achieving higher scan speeds in tapping-mode atomic force microscopy. Such active cantilevers are a significant milestone to eventually obtain video-rate on-chip atomic force microscopes (AFMs) that can even surpass the functionality and imaging speed of their macroscale counterparts at a significantly lower cost. In this brief, we present an active AFM cantilever with an on-chip actuator and two built-in displacement sensors, designed to be integrated into on-chip AFMs. The common feedthrough problem present in this type of architecture is addressed by a differential sensing configuration, and the revealed dynamics are used for the system identification. A positive position feedback controller is designed to actively tailor the Q factor of the cantilever. The imaging performance of the microcantilever with and without Q control is compared by attenuating the cantilever's Q factor from 177 to 15 using the feedback loop. A common artifact in high-speed scans, the parachuting effect, is mitigated, rendering higher imaging speeds achievable.
- 17 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 16 (21) , 7774-7783
A 4-DOF MEMS Energy Harvester Using Ultrasonic Excitation
This paper presents a microelectromechanical systems (MEMS)-based energy harvester that is designed to harvest electrical energy from an external source of ultrasonic waves. The harvester features a novel 4-degree-of-freedom (DOF) mechanical design that uses three translational resonance modes and one rotational mode, with electrostatic transducers being implemented to perform the conversion of mechanical to electrical energy. The 4-DOF design of the system allows energy to be harvested regardless of the device's orientation, which holds particular benefits for potential applications that include the powering of implanted biomedical devices. Full characterization of the fabricated MEMS harvester is performed, which shows that the device is able to generate electrical power outputs of 180, 189, and 49.1 nW due to ultrasonic excitation from the x-, y-, and z-directions, respectively.
- 17 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 16 (21) , 7774-7783
A 4-DOF MEMS Energy Harvester Using Ultrasonic Excitation
This paper presents a microelectromechanical systems (MEMS)-based energy harvester that is designed to harvest electrical energy from an external source of ultrasonic waves. The harvester features a novel 4-degree-of-freedom (DOF) mechanical design that uses three translational resonance modes and one rotational mode, with electrostatic transducers being implemented to perform the conversion of mechanical to electrical energy. The 4-DOF design of the system allows energy to be harvested regardless of the device's orientation, which holds particular benefits for potential applications that include the powering of implanted biomedical devices. Full characterization of the fabricated MEMS harvester is performed, which shows that the device is able to generate electrical power outputs of 180, 189, and 49.1 nW due to ultrasonic excitation from the x-, y-, and z-directions, respectively.