Eli M. Gray‐Stuart
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eli M. Gray‐Stuart has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- John E. Bronlund
School of Food and Advanced Technology, Massey University, Palmerston North, New Zealand
5 shared publications - Celia Kueh
School of Food and Advanced Technology Massey University Private Bag 11 222 Palmerston North 4442 New Zealand
3 shared publications - Karl Dahm
Callaghan Innovation 69 Gracefield Road Lower Hutt 5010 New Zealand
3 shared publications - Mohamad Aiman Jamsari
School of Food and Advanced Technology Massey University Private Bag 11 222 Palmerston North 4442 New Zealand
3 shared publications Anne Saint-Eve
1 shared publication- Emma E. Gobes
Bioeconomy Science Institute, Tuhiraki, Lincoln, New Zealand
1 shared publication
Latest Publications
- Open Access
- 1 July 2026
- Published by Springer Nature in Cellulose
- Vol. 33 (11) , 6479-6496
Characterising fibre alignment in moulded fibre materials across X, Y, and Z axes
Moulded fibre is emerging as a sustainable alternative to single-use plastic items, commonly used for food and non-food packaging. Yet its mechanical properties are often inferior to oriented paper products, due to the limited fibre alignment during forming. This study introduces a method for characterising fibre orientation (FO) within moulded fibre products, enabling analysis of pulp flow patterns and turbulence during the production of moulded fibre items. The fibre alignment is characterised by sheet splitting the samples using an automated sheet splitter, and high-resolution scans of the split layers were analysed using MATLAB Structure Tensor analysis to determine the fibre orientation (FO) in the X and Y directions. The MATLAB analyses provided FO distribution across layers, in the Z-direction and offered insights into X and Y directional alignment. Outputs included visual heatmaps using a block approach and quantitative metrics. This approach enables efficient, detailed FO characterisation throughout the layers of a product, allowing for further improvement of moulded fibre properties. Validation results showed accurate and sensitive results. This method introduces opportunities to understand and control fibre alignment, a key step toward improving the strength properties of moulded fibre packaging.
- 1 July 2026
- Published by Springer Nature in Cellulose
- Vol. 33 (11) , 6479-6496
Open AccessCharacterising fibre alignment in moulded fibre materials across X, Y, and Z axes
Moulded fibre is emerging as a sustainable alternative to single-use plastic items, commonly used for food and non-food packaging. Yet its mechanical properties are often inferior to oriented paper products, due to the limited fibre alignment during forming. This study introduces a method for characterising fibre orientation (FO) within moulded fibre products, enabling analysis of pulp flow patterns and turbulence during the production of moulded fibre items. The fibre alignment is characterised by sheet splitting the samples using an automated sheet splitter, and high-resolution scans of the split layers were analysed using MATLAB Structure Tensor analysis to determine the fibre orientation (FO) in the X and Y directions. The MATLAB analyses provided FO distribution across layers, in the Z-direction and offered insights into X and Y directional alignment. Outputs included visual heatmaps using a block approach and quantitative metrics. This approach enables efficient, detailed FO characterisation throughout the layers of a product, allowing for further improvement of moulded fibre properties. Validation results showed accurate and sensitive results. This method introduces opportunities to understand and control fibre alignment, a key step toward improving the strength properties of moulded fibre packaging.
- 30 June 2023
- Published by Elsevier in Journal of Food Engineering
- Vol. 357
Modelling mastication and aroma release from white rice during food oral processing
- 30 June 2023
- Published by Elsevier in Journal of Food Engineering
- Vol. 357
Modelling mastication and aroma release from white rice during food oral processing
- Open Access
- 4 March 2022
- Published by Wiley in Packaging Technology and Science
- Vol. 35 (6) , 497-504
Influence of different box preparations on creep performance of corrugated fibreboard boxes subject to constant and cycling relative humidity environments
- 4 March 2022
- Published by Wiley in Packaging Technology and Science
- Vol. 35 (6) , 497-504
Open AccessInfluence of different box preparations on creep performance of corrugated fibreboard boxes subject to constant and cycling relative humidity environments
- 3 February 2020
- Published by Wiley in Packaging Technology and Science
- Vol. 33 (4-5) , 159-170
Modelling the impact of crushing on the strength performance of corrugated fibreboard
This paper presents different ways of modelling the strength of corrugated fibreboard (CFB) subjected to different levels of pre‐crushing. The strength performance was measured through four‐point bending loading and edge crush test (ECT). The models used in this study were an analytical solution, an equivalent flute model, and detailed flute geometry models that consisted of idealized sine geometry and real geometry.The study found that the bending performance was dependent on the calliper of CFB rather than the flute geometry. All models showed a similar trend in predicting the drop in bending stiffness as the level of pre‐crushing increased, albeit with different absolute value.It was found that the real geometry model of the board predicted ECT performance better than the other models. However, at severe pre‐crushing levels (>50%), there was a significant drop in the experimental ECT force not predicted by the models. For these cases, there was evidence of delamination of the flute, a failure mechanism that was not included in any of the models.The analytical solution model provides the quickest prediction but could not predict the crushed ECT performance due to not considering the calliper variable in the equation. The equivalent model showed faster solving time compared with both real and idealized geometry models, although these microgeometry models predicted ECT the most accurately.
- 3 February 2020
- Published by Wiley in Packaging Technology and Science
- Vol. 33 (4-5) , 159-170
Modelling the impact of crushing on the strength performance of corrugated fibreboard
This paper presents different ways of modelling the strength of corrugated fibreboard (CFB) subjected to different levels of pre‐crushing. The strength performance was measured through four‐point bending loading and edge crush test (ECT). The models used in this study were an analytical solution, an equivalent flute model, and detailed flute geometry models that consisted of idealized sine geometry and real geometry.The study found that the bending performance was dependent on the calliper of CFB rather than the flute geometry. All models showed a similar trend in predicting the drop in bending stiffness as the level of pre‐crushing increased, albeit with different absolute value.It was found that the real geometry model of the board predicted ECT performance better than the other models. However, at severe pre‐crushing levels (>50%), there was a significant drop in the experimental ECT force not predicted by the models. For these cases, there was evidence of delamination of the flute, a failure mechanism that was not included in any of the models.The analytical solution model provides the quickest prediction but could not predict the crushed ECT performance due to not considering the calliper variable in the equation. The equivalent model showed faster solving time compared with both real and idealized geometry models, although these microgeometry models predicted ECT the most accurately.
- 29 July 2019
- Published by Wiley in Packaging Technology and Science
- Vol. 32 (11) , 555-565
Experimental and numerical performance of corrugated fibreboard at different orientations under four‐point bending test
This paper presents experimental work, finite element (FE) model, and analytical solution for predicting the four‐point bending on C‐flute corrugated fibreboard (CFB) when oriented at different angles. The angles of the CFB samples used in this research study were 0° (cross‐machine direction) and 30°, 45°, 60°, and 90° (machine direction). The CFB was assumed as an orthotropic shell element in the FE model and was validated by comparing the bending stiffness, maximum bending force, and failure formation from the experimental test. It was found in the experiment that the 90° sample had the highest bending stiffness with the lowest maximum bending force while the 0° sample had the opposite. An interesting finding was that the 30° and 45° samples improve the bending stiffness than does 0° without significantly affecting the maximum bending force. Both the FE model and analytical solution predicted the bending stiffness trend of the board from 0° to 90° with good agreement compared with experimental results. The maximum bending force in the FE model showed reasonable agreement with the experimental findings. The failure regions on the samples showed similar patterns in both experiments and the FE model. The accurate response in the FE model justify that it is a good tool to predict the bending behaviour of CFB.
- 29 July 2019
- Published by Wiley in Packaging Technology and Science
- Vol. 32 (11) , 555-565
Experimental and numerical performance of corrugated fibreboard at different orientations under four‐point bending test
This paper presents experimental work, finite element (FE) model, and analytical solution for predicting the four‐point bending on C‐flute corrugated fibreboard (CFB) when oriented at different angles. The angles of the CFB samples used in this research study were 0° (cross‐machine direction) and 30°, 45°, 60°, and 90° (machine direction). The CFB was assumed as an orthotropic shell element in the FE model and was validated by comparing the bending stiffness, maximum bending force, and failure formation from the experimental test. It was found in the experiment that the 90° sample had the highest bending stiffness with the lowest maximum bending force while the 0° sample had the opposite. An interesting finding was that the 30° and 45° samples improve the bending stiffness than does 0° without significantly affecting the maximum bending force. Both the FE model and analytical solution predicted the bending stiffness trend of the board from 0° to 90° with good agreement compared with experimental results. The maximum bending force in the FE model showed reasonable agreement with the experimental findings. The failure regions on the samples showed similar patterns in both experiments and the FE model. The accurate response in the FE model justify that it is a good tool to predict the bending behaviour of CFB.
- 6 May 2019
- Published by Springer Nature in Cellulose
- Vol. 26 (9) , 5695-5705
Measurement of thermal conductivity of paper and corrugated fibreboard with prediction of thermal performance for design applications
- 6 May 2019
- Published by Springer Nature in Cellulose
- Vol. 26 (9) , 5695-5705
Measurement of thermal conductivity of paper and corrugated fibreboard with prediction of thermal performance for design applications
- 14 March 2019
- Published by Wiley in Packaging Technology and Science
- Vol. 32 (5) , 213-226
A technique to quantify morphological damage of the flute profile in the midplane of corrugated fibreboard
This research presents a technique to quantify morphological damage to flutes in corrugated fibreboard (CFB). The method involves laser cutting thin samples and analysing digital images of the flute profiles. The surface profiles of creased CFB before and after laser cutting were measured using fringe projection and showed that the sample preparation does not significantly affect the flute profile. After imaging the laser cut samples, skeleton analysis was used to derive a digitised profile of the flute shape. To characterise the level of damage to the flute profile, a similarity factor (SF) was introduced to quantify the relative difference between test sample and reference flute profiles. Validation of this analysis technique was done by generating known images of flute profile with variations that include distortions that could occur to CFB. These images were then fed into the skeleton analysis, and the results were compared with the original profile. This comparison showed good agreement between the initial and skeleton‐analysed flutes. A demonstration of the skeleton analysis on purposefully damaged actual CFB flute profiles shows that the SF reduces as the level of crushing increases, showing that the technique could be used to enumerate morphological damage to CFB during manufacture, conversion, and use.
- 14 March 2019
- Published by Wiley in Packaging Technology and Science
- Vol. 32 (5) , 213-226
A technique to quantify morphological damage of the flute profile in the midplane of corrugated fibreboard
This research presents a technique to quantify morphological damage to flutes in corrugated fibreboard (CFB). The method involves laser cutting thin samples and analysing digital images of the flute profiles. The surface profiles of creased CFB before and after laser cutting were measured using fringe projection and showed that the sample preparation does not significantly affect the flute profile. After imaging the laser cut samples, skeleton analysis was used to derive a digitised profile of the flute shape. To characterise the level of damage to the flute profile, a similarity factor (SF) was introduced to quantify the relative difference between test sample and reference flute profiles. Validation of this analysis technique was done by generating known images of flute profile with variations that include distortions that could occur to CFB. These images were then fed into the skeleton analysis, and the results were compared with the original profile. This comparison showed good agreement between the initial and skeleton‐analysed flutes. A demonstration of the skeleton analysis on purposefully damaged actual CFB flute profiles shows that the SF reduces as the level of crushing increases, showing that the technique could be used to enumerate morphological damage to CFB during manufacture, conversion, and use.