Alberto Coronado-Mendoza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alberto Coronado-Mendoza has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
- Kelly Joel Gurubel Tun
Universidad de Guadalajara
8 shared publications - Jesús Sergio Artal-Sevil
Departamento de Ingeniería Eléctrica, Universidad de Zaragoza, C/María de Luna, 3, 50018 Zaragoza, Spain
6 shared publications - José Antonio Dominguez-Navarro
Department of Electrical Engineering, School of Engineering and Architecture, University of Zaragoza, C/María de Luna, 50018 Zaragoza, Spain
6 shared publications - Mónica Camas-Náfate
Studies on Water and Energy Department, University of Guadalajara, Tonala Campus, Nuevo Periferico Av. 555, Jalisco 45425, Mexico
4 shared publications - Belkis Sulbarán-Rangel
Department of Water and Energy, University of Guadalajara Campus Tonalá, Tonalá 45425, Mexico
3 shared publications - Carlos Jesahel Vega Gómez
Universidad de Guadalajara
3 shared publications
Latest Publications
- Open Access
- 12 September 2025
- Published by MDPI AG in Electronics
- Vol. 14 (18) , 3622
High-Efficiency Partial-Power Converter with Dual-Loop PI-Sliding Mode Control for PV Systems
This paper presents a novel partial-power DC-DC converter architecture specifically designed for Photovoltaic (PV) energy systems. Unlike traditional full-power converters, the proposed topology processes only a fraction of the total power, resulting in improved overall efficiency, reduced component stress, and lower system cost. The converter is integrated into a PV-based energy system and regulated by a dual-loop control strategy consisting of a Proportional-Integral (PI) voltage controller and an inner Sliding-Mode Controller (SMC) for current regulation. This control scheme ensures robust tracking performance under dynamic variations in irradiance, load, and reference voltage. The paper provides a comprehensive mathematical model and control formulation, emphasizing the robustness and fast transient response offered by SMC. Simulation results obtained in MATLAB-Simulink, along with real-time implementation on the OPAL-RT hardware-in-the-loop (HIL) platform, confirm the effectiveness of the proposed design. The system achieves stable voltage regulation with low ripple and accurate current tracking. Compared to conventional boost configurations, the proposed converter demonstrates superior performance, particularly under moderate voltage conversion conditions. The system achieves high efficiency levels, validated through both analytical estimation and real-time hardware-in-the-loop (HIL) implementation. Its high efficiency, scalability, and real-time control feasibility make it a promising solution for next-generation PV systems, battery interfacing, and DC-microgrid applications.
- 12 September 2025
- Published by MDPI AG in Electronics
- Vol. 14 (18) , 3622
Open AccessHigh-Efficiency Partial-Power Converter with Dual-Loop PI-Sliding Mode Control for PV Systems
This paper presents a novel partial-power DC-DC converter architecture specifically designed for Photovoltaic (PV) energy systems. Unlike traditional full-power converters, the proposed topology processes only a fraction of the total power, resulting in improved overall efficiency, reduced component stress, and lower system cost. The converter is integrated into a PV-based energy system and regulated by a dual-loop control strategy consisting of a Proportional-Integral (PI) voltage controller and an inner Sliding-Mode Controller (SMC) for current regulation. This control scheme ensures robust tracking performance under dynamic variations in irradiance, load, and reference voltage. The paper provides a comprehensive mathematical model and control formulation, emphasizing the robustness and fast transient response offered by SMC. Simulation results obtained in MATLAB-Simulink, along with real-time implementation on the OPAL-RT hardware-in-the-loop (HIL) platform, confirm the effectiveness of the proposed design. The system achieves stable voltage regulation with low ripple and accurate current tracking. Compared to conventional boost configurations, the proposed converter demonstrates superior performance, particularly under moderate voltage conversion conditions. The system achieves high efficiency levels, validated through both analytical estimation and real-time hardware-in-the-loop (HIL) implementation. Its high efficiency, scalability, and real-time control feasibility make it a promising solution for next-generation PV systems, battery interfacing, and DC-microgrid applications.
- 10 June 2025
- Published by Astra Ediciones
- p. 97-122
Edificios inteligentes: el papel de la IA en la transición energética y en el cambio de conducta del ciudadano
El presente capítulo establece algunas bases para la creación de una nueva cultura energética al interior de las organizaciones, donde los usuarios de los edificios, al estar informados en tiempo real sobre la huella de carbono que generan sus actividades diarias, pueden emprender acciones para su mitigación, asistidos por inteligencia artificial. Primeramente, se presenta cómo el cambio climático está estrechamente relacionado con la demanda de energía eléctrica a partir de la quema de combustibles fósiles. Se presentan algunos datos relevantes sobre la generación de energía en México y su consumo en el Área Metropolitana de Guadalajara.
- 10 June 2025
- Published by Astra Ediciones
- p. 97-122
Edificios inteligentes: el papel de la IA en la transición energética y en el cambio de conducta del ciudadano
El presente capítulo establece algunas bases para la creación de una nueva cultura energética al interior de las organizaciones, donde los usuarios de los edificios, al estar informados en tiempo real sobre la huella de carbono que generan sus actividades diarias, pueden emprender acciones para su mitigación, asistidos por inteligencia artificial. Primeramente, se presenta cómo el cambio climático está estrechamente relacionado con la demanda de energía eléctrica a partir de la quema de combustibles fósiles. Se presentan algunos datos relevantes sobre la generación de energía en México y su consumo en el Área Metropolitana de Guadalajara.
- 10 June 2025
- Published by Astra Ediciones
- p. 13-16
Introducción
El crecimiento acelerado de la población mundial, junto con el incremento en la demanda de energía por diversas causas como el calentamiento global, entre otras, ha puesto de manifiesto la necesidad imperante de transformar el sistema energético global. La eficiencia energética junto con las energías renovables y los sistemas de gestión energética, emergen como una respuesta contundente a este reto, ofreciendo soluciones sostenibles que no solo mitigan el cambio climático, sino que también promueven un desarrollo económico y social inclusivo. Sin embargo, la adopción de estas tecnologías no está exenta de desafíos. Este libro, titulado Energías Renovables: Generación, Distribución, Almacenamiento y su Impacto en los Países en Desarrollo, ofrece una perspectiva integral sobre las oportunidades y los obstáculos que enfrentan las naciones en el camino hacia una transición energética justa y sostenible. El contenido de esta obra se estructura en trece capítulos que abordan temas diversos y relevantes. Cada capítulo aporta una visión única y basada en evidencias sobre aspectos clave del panorama energético actual, destacando estudios de caso y análisis teóricos que enriquecen la comprensión de las energías renovables y su aplicación en diferentes contextos.
- 10 June 2025
- Published by Astra Ediciones
- p. 13-16
Introducción
El crecimiento acelerado de la población mundial, junto con el incremento en la demanda de energía por diversas causas como el calentamiento global, entre otras, ha puesto de manifiesto la necesidad imperante de transformar el sistema energético global. La eficiencia energética junto con las energías renovables y los sistemas de gestión energética, emergen como una respuesta contundente a este reto, ofreciendo soluciones sostenibles que no solo mitigan el cambio climático, sino que también promueven un desarrollo económico y social inclusivo. Sin embargo, la adopción de estas tecnologías no está exenta de desafíos. Este libro, titulado Energías Renovables: Generación, Distribución, Almacenamiento y su Impacto en los Países en Desarrollo, ofrece una perspectiva integral sobre las oportunidades y los obstáculos que enfrentan las naciones en el camino hacia una transición energética justa y sostenible. El contenido de esta obra se estructura en trece capítulos que abordan temas diversos y relevantes. Cada capítulo aporta una visión única y basada en evidencias sobre aspectos clave del panorama energético actual, destacando estudios de caso y análisis teóricos que enriquecen la comprensión de las energías renovables y su aplicación en diferentes contextos.
- Open Access
Optimum Design of a Photovoltaic Inverter System Based on Ga, Pso and Gwo Algorithms with a Mppt Sliding Mode Control
The deployment of photovoltaic single-phase inverters has been rapidly increasing worldwide. However, the performance of these systems is highly influenced by atmospheric conditions and load variations, necessitating the development of performance indices to enhance their efficiency and energy quality. In this study, four performance indices are proposed to evaluate the efficiency and energy quality of photovoltaic systems quantitatively. The entire process is analyzed, encompassing solar energy capture, DC-DC and DC-AC conversion, and filtering, to deliver maximum energy and quality to the load. Furthermore, eight system parameters are optimized using advanced techniques such as genetic algorithms, particle swarm optimization, and gray wolf optimization. These optimizations enhance the global performance of two critical stages: (1) the maximum power point tracking algorithm based on sliding mode control, which minimizes switching losses in the boost stage, and (2) the effective transfer of captured solar power to the load by optimizing the gains of a PI controller. The PI controller computes the switching triggers for the inverter stage, significantly improving the total harmonic distortion of voltage and current waveforms. Simulation results validate the proposed approach, demonstrating a marked improvement in overall system efficiency (95.8%) when compared to the incremental conductance method (−11.8%) and a baseline sliding mode control configuration (−1.14%).
Open AccessOptimum Design of a Photovoltaic Inverter System Based on Ga, Pso and Gwo Algorithms with a Mppt Sliding Mode Control
The deployment of photovoltaic single-phase inverters has been rapidly increasing worldwide. However, the performance of these systems is highly influenced by atmospheric conditions and load variations, necessitating the development of performance indices to enhance their efficiency and energy quality. In this study, four performance indices are proposed to evaluate the efficiency and energy quality of photovoltaic systems quantitatively. The entire process is analyzed, encompassing solar energy capture, DC-DC and DC-AC conversion, and filtering, to deliver maximum energy and quality to the load. Furthermore, eight system parameters are optimized using advanced techniques such as genetic algorithms, particle swarm optimization, and gray wolf optimization. These optimizations enhance the global performance of two critical stages: (1) the maximum power point tracking algorithm based on sliding mode control, which minimizes switching losses in the boost stage, and (2) the effective transfer of captured solar power to the load by optimizing the gains of a PI controller. The PI controller computes the switching triggers for the inverter stage, significantly improving the total harmonic distortion of voltage and current waveforms. Simulation results validate the proposed approach, demonstrating a marked improvement in overall system efficiency (95.8%) when compared to the incremental conductance method (−11.8%) and a baseline sliding mode control configuration (−1.14%).
- 1 May 2024
- Published by Comunicacion Cientifica
Agua y energía: Actualidad y retos para un desarrollo sostenible
Ediciones Comunicación Científica se especializa en la publicación de libros dictaminados, digitales e impresos, mediante el sistema de pares ciegos académicos, acceso abierto al texto completo, métricas, DOI, Epub, indización internacional, ética editorial, comités editoriales, campaña de comunicación en las áreas de humanidades, sociales y ciencias.
- 1 May 2024
- Published by Comunicacion Cientifica
Agua y energía: Actualidad y retos para un desarrollo sostenible
Ediciones Comunicación Científica se especializa en la publicación de libros dictaminados, digitales e impresos, mediante el sistema de pares ciegos académicos, acceso abierto al texto completo, métricas, DOI, Epub, indización internacional, ética editorial, comités editoriales, campaña de comunicación en las áreas de humanidades, sociales y ciencias.
- Open Access
Optimizing Lithium-Ion Battery Modeling: A Comparative Analysis of PSO and GWO Algorithms
In recent years, the modeling and simulation of lithium-ion batteries have garnered attention due to the rising demand for reliable energy storage. Accurate charge cycle predictions are fundamental for optimizing battery performance and lifespan. This study compares particle swarm optimization (PSO) and grey wolf optimization (GWO) algorithms in modeling a commercial lithium-ion battery, emphasizing the voltage behavior and the current delivered to the battery. Bio-inspired optimization tunes parameters to reduce the root mean square error (RMSE) between simulated and experimental outputs. The model, implemented in MATLAB/Simulink, integrates electrochemical parameters and estimates battery behavior under varied conditions. The assessment of terminal voltage revealed notable enhancements in the model through both the PSO and GWO algorithms compared to the non-optimized model. The GWO-optimized model demonstrated superior performance, with a reduced RMSE of 0.1700 (25 °C; 3.6 C, 455 s) and 0.1705 (25 °C; 3.6 C, 10,654 s) compared to the PSO-optimized model, achieving a 42% average RMSE reduction. Battery current was identified as a key factor influencing the model analysis, with optimized models, particularly the GWO model, exhibiting enhanced predictive capabilities and slightly lower RMSE values than the PSO model. This offers practical implications for battery integration into energy systems. Analyzing the execution time with different population values for PSO and GWO provides insights into computational complexity. PSO exhibited greater-than-linear dynamics, suggesting a polynomial complexity of O(nk), while GWO implied a potential polynomial complexity within the range of O(nk) or O(2n) based on execution times from populations of 10 to 1000.
Open AccessOptimizing Lithium-Ion Battery Modeling: A Comparative Analysis of PSO and GWO Algorithms
In recent years, the modeling and simulation of lithium-ion batteries have garnered attention due to the rising demand for reliable energy storage. Accurate charge cycle predictions are fundamental for optimizing battery performance and lifespan. This study compares particle swarm optimization (PSO) and grey wolf optimization (GWO) algorithms in modeling a commercial lithium-ion battery, emphasizing the voltage behavior and the current delivered to the battery. Bio-inspired optimization tunes parameters to reduce the root mean square error (RMSE) between simulated and experimental outputs. The model, implemented in MATLAB/Simulink, integrates electrochemical parameters and estimates battery behavior under varied conditions. The assessment of terminal voltage revealed notable enhancements in the model through both the PSO and GWO algorithms compared to the non-optimized model. The GWO-optimized model demonstrated superior performance, with a reduced RMSE of 0.1700 (25 °C; 3.6 C, 455 s) and 0.1705 (25 °C; 3.6 C, 10,654 s) compared to the PSO-optimized model, achieving a 42% average RMSE reduction. Battery current was identified as a key factor influencing the model analysis, with optimized models, particularly the GWO model, exhibiting enhanced predictive capabilities and slightly lower RMSE values than the PSO model. This offers practical implications for battery integration into energy systems. Analyzing the execution time with different population values for PSO and GWO provides insights into computational complexity. PSO exhibited greater-than-linear dynamics, suggesting a polynomial complexity of O(nk), while GWO implied a potential polynomial complexity within the range of O(nk) or O(2n) based on execution times from populations of 10 to 1000.
- Open Access
- 28 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14035
Modeling and Simulation of a Commercial Lithium-Ion Battery with Charge Cycle Predictions
The analysis of the behavior of lithium-ion batteries has gained considerable interest in recent years. There are different alternatives for the analysis of this behavior; however, depending on the type of modeling, there are application and optimization restrictions. In this work, a hybrid model has been made that is capable of predicting the characteristics of a lithium-ion battery. As a novelty, the simplification, at the same time, facilitates the sampling of parameters for their prompt selection for optimization. A new model open to the user is proposed, which has proven to be efficient in simulation time. For example, one hour simulates it in 5 min, providing information detailing how these parameters, State of Health (SOH), Open Circuit Voltage (VOC), State of charge (SOC), and Number of charge and discharge cycles, in the face of temperature variations and charge and discharge cycles. Opening the possibility of optimizing the parameters with different techniques to estimate the performance and dynamics in the face of temperature change and charge and discharge cycles. A model based on linear regressions, manufacturer characteristics, and integrating equations in the electrical model of electrochemical phenomena is proposed.
- 28 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14035
Open AccessModeling and Simulation of a Commercial Lithium-Ion Battery with Charge Cycle Predictions
The analysis of the behavior of lithium-ion batteries has gained considerable interest in recent years. There are different alternatives for the analysis of this behavior; however, depending on the type of modeling, there are application and optimization restrictions. In this work, a hybrid model has been made that is capable of predicting the characteristics of a lithium-ion battery. As a novelty, the simplification, at the same time, facilitates the sampling of parameters for their prompt selection for optimization. A new model open to the user is proposed, which has proven to be efficient in simulation time. For example, one hour simulates it in 5 min, providing information detailing how these parameters, State of Health (SOH), Open Circuit Voltage (VOC), State of charge (SOC), and Number of charge and discharge cycles, in the face of temperature variations and charge and discharge cycles. Opening the possibility of optimizing the parameters with different techniques to estimate the performance and dynamics in the face of temperature change and charge and discharge cycles. A model based on linear regressions, manufacturer characteristics, and integrating equations in the electrical model of electrochemical phenomena is proposed.
- 12 April 2022
- Published by Springer Nature
- p. 91-105
Green Energy HPC Data Centers to Improve Processing Cost Efficiency
- 12 April 2022
- Published by Springer Nature
- p. 91-105
Green Energy HPC Data Centers to Improve Processing Cost Efficiency
- Open Access
- 12 February 2022
- Published by Elsevier in Energy Reports
- Vol. 8, 2712-2725
Optimizing the penetration of standalone microgrid, incorporating demand side management as a guiding principle
- 12 February 2022
- Published by Elsevier in Energy Reports
- Vol. 8, 2712-2725
Open AccessOptimizing the penetration of standalone microgrid, incorporating demand side management as a guiding principle
- Open Access
Robust Inverse Optimal Control for a Boost Converter
The variability of renewable energies and their integration into the grid via power electronics demands the design of robust control algorithms. This work incorporates two techniques to ensure the stability of a boost converter through its state equations, implementing the inverse optimal control and the gain-scheduling technique for robust control settings. In such a way that, under a single adjustment, it is capable of damping different changes such as changes in the parameters, changes in the load, the input voltage, and the reference voltage. On the other hand, inverse optimal control is based on a discrete-time control Lyapunov function (CLF), and CLF candidate depends on fixed parameters that are selected to obtain the solution for inverse optimal control. Once these parameters have been found through heuristic or artificial intelligence methods, the new proposed methodology is capable of obtaining a robust optimal control scheme, without having to search for new parameters through other methods, since these are sometimes sensitive changes and many times the process of a new search is delayed. The results of the approach are simulated using Matlab, obtaining good performance of the proposed control under different operation conditions. Such simulations yielded errors of less than 1% based on the voltage reference, given the disturbances caused by changes in the input variables, system parameters, and changes in the reference. Thus, applying the new methodology, the stability of our system was preserved in all cases.
Open AccessRobust Inverse Optimal Control for a Boost Converter
The variability of renewable energies and their integration into the grid via power electronics demands the design of robust control algorithms. This work incorporates two techniques to ensure the stability of a boost converter through its state equations, implementing the inverse optimal control and the gain-scheduling technique for robust control settings. In such a way that, under a single adjustment, it is capable of damping different changes such as changes in the parameters, changes in the load, the input voltage, and the reference voltage. On the other hand, inverse optimal control is based on a discrete-time control Lyapunov function (CLF), and CLF candidate depends on fixed parameters that are selected to obtain the solution for inverse optimal control. Once these parameters have been found through heuristic or artificial intelligence methods, the new proposed methodology is capable of obtaining a robust optimal control scheme, without having to search for new parameters through other methods, since these are sometimes sensitive changes and many times the process of a new search is delayed. The results of the approach are simulated using Matlab, obtaining good performance of the proposed control under different operation conditions. Such simulations yielded errors of less than 1% based on the voltage reference, given the disturbances caused by changes in the input variables, system parameters, and changes in the reference. Thus, applying the new methodology, the stability of our system was preserved in all cases.