Olivier Gravrand
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Olivier Gravrand has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
N. Baier
9 shared publicationsC. Cervera
7 shared publicationsO. Boulade
CEA-Irfu
7 shared publicationsC. Lobre
5 shared publicationsJ. Rothman
CEA-LETI-MINATEC, Grenoble, France
5 shared publicationsG. Destefanis
CEA-LETI-MINATEC, Grenoble, France
4 shared publications
Latest Publications
- Open Access
- 29 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (8) , 6660-6667
EBIC Characterization of Vertical Transport of Minority Carriers in Gallium-Free Type-II Superlattices for Infrared Detectors
InAs/InAsSb type-II superlattices (T2SLs) are emerging as alternatives to HgCdTe for infrared detection, but their anisotropic hole transport could be a limitation in small-pitch focal plane array (FPA) detectors. To quantitatively assess this anisotropy in the device, modulated electron beam induced current (AC-EBIC) is performed on deep-etched mid-wave infrared (MWIR) T2SL photodiodes. Analysis of the EBIC amplitude and phase profiles reveals a transport anisotropy of 2.5 between lateral and vertical diffusion lengths. A numerical diffusion model fits the data, yielding diffusion lengths (3–4 μm vertically, 7–10 μm laterally), minority carrier lifetime (400–670 ns), and surface recombination velocity (< 800 cm/s). While AC-EBIC effectively quantifies transport anisotropy, current frequency constraints limit the decoupling of individual parameters. Nevertheless, beyond surface characterization, this study demonstrates AC-EBIC’s potential to resolve anisotropic diffusion parameters in photodiodes structures.
- 29 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (8) , 6660-6667
Open AccessEBIC Characterization of Vertical Transport of Minority Carriers in Gallium-Free Type-II Superlattices for Infrared Detectors
InAs/InAsSb type-II superlattices (T2SLs) are emerging as alternatives to HgCdTe for infrared detection, but their anisotropic hole transport could be a limitation in small-pitch focal plane array (FPA) detectors. To quantitatively assess this anisotropy in the device, modulated electron beam induced current (AC-EBIC) is performed on deep-etched mid-wave infrared (MWIR) T2SL photodiodes. Analysis of the EBIC amplitude and phase profiles reveals a transport anisotropy of 2.5 between lateral and vertical diffusion lengths. A numerical diffusion model fits the data, yielding diffusion lengths (3–4 μm vertically, 7–10 μm laterally), minority carrier lifetime (400–670 ns), and surface recombination velocity (< 800 cm/s). While AC-EBIC effectively quantifies transport anisotropy, current frequency constraints limit the decoupling of individual parameters. Nevertheless, beyond surface characterization, this study demonstrates AC-EBIC’s potential to resolve anisotropic diffusion parameters in photodiodes structures.
- Open Access
- 3 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (8) , 6529-6543
Status of IR Imaging Detector Developments at LETI
Since 1976, CEA-LETI has played a pivotal role in the development of second-generation cooled imaging focal plane array (FPA) technology. Initially, the focus was on II-VI HgCdTe arrays, which led to the establishment of Sofradir, now known as Lynred. In addition, III-V material systems have been investigated over time, including for instance InSb for mid-wave infrared (IR) with Safran. Later, the development of bulk InAsSb with III-V Lab and Lynred was initiated for high-operating- temperature (HOT) blue mid-wave applications. Currently, type-II superlattice (T2SL) development for HOT mid-wave is under active investigation, as well as InGaAs for short-wave IR with STmicro. Alongside these developments in III-V technology, significant advancements have been made in II-VI technology. These include very low-dark-current short-wave large arrays for astronomy, enhanced manufacturability and high image quality for HOT mid-wave and long-wave IR, and the actual development of very long-wave IR for space applications. Our laboratory has been involved in those wide-ranging developments, enabling us to provide a balanced assessment of the pros and cons of each technology, targeting various applications and spectral bands. This paper will provide an update on the latest developments at LETI in collaboration with industry partners. In this context, the ability to thoroughly understand the material properties, accurately assess the fabrication process, and utilize advanced characterization techniques is essential for evaluating the performance achieved. We are therefore studying not only first-order figures of merit (quantum efficiency, dark current, etc.), but also second-order performance metrics (non-uniformity correction stability, low-frequency noise, pixel modulation transfer function, persistence).
- 3 June 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (8) , 6529-6543
Open AccessStatus of IR Imaging Detector Developments at LETI
Since 1976, CEA-LETI has played a pivotal role in the development of second-generation cooled imaging focal plane array (FPA) technology. Initially, the focus was on II-VI HgCdTe arrays, which led to the establishment of Sofradir, now known as Lynred. In addition, III-V material systems have been investigated over time, including for instance InSb for mid-wave infrared (IR) with Safran. Later, the development of bulk InAsSb with III-V Lab and Lynred was initiated for high-operating- temperature (HOT) blue mid-wave applications. Currently, type-II superlattice (T2SL) development for HOT mid-wave is under active investigation, as well as InGaAs for short-wave IR with STmicro. Alongside these developments in III-V technology, significant advancements have been made in II-VI technology. These include very low-dark-current short-wave large arrays for astronomy, enhanced manufacturability and high image quality for HOT mid-wave and long-wave IR, and the actual development of very long-wave IR for space applications. Our laboratory has been involved in those wide-ranging developments, enabling us to provide a balanced assessment of the pros and cons of each technology, targeting various applications and spectral bands. This paper will provide an update on the latest developments at LETI in collaboration with industry partners. In this context, the ability to thoroughly understand the material properties, accurately assess the fabrication process, and utilize advanced characterization techniques is essential for evaluating the performance achieved. We are therefore studying not only first-order figures of merit (quantum efficiency, dark current, etc.), but also second-order performance metrics (non-uniformity correction stability, low-frequency noise, pixel modulation transfer function, persistence).
- Open Access
- 11 August 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (10) , 8350-8362
Extraction of Trap Parameters in HgCdTe P/N MWIR Focal Plane Arrays Using Photocurrent Transients Induced by Optical Excitation
Since their initial synthesis in 1958, HgCdTe compounds have been extensively developed as a highly effective material for infrared detection. The performance of these materials has improved continuously in terms of the first-order figures of merit, including dark current, quantum efficiency, and signal-to-noise ratio. Nowadays, the optimization of second-order performances is a key objective, with a particular focus on low-amplitude transients of photocurrents induced by scene illumination variation. In this study, we conducted measurements of photocurrent transients induced by optical excitation on HgCdTe mid-wave infrared (MWIR) focal plane arrays (FPAs). The HgCdTe detection circuit is flip-chipped onto a silicon direct injection readout integrated circuit (DI ROIC). The transients were measured at various temperatures, wavelengths, and levels of illumination. Furthermore, the bias of the photodiodes was varied in order to examine the impact of the space charge region extension. The FPA exhibits remarkably brief transients at operational temperatures (2.6 ms at 130 K) and low amplitudes relative to typical operational requirements. Two exponential regimes with two distinct time constants were identified in each transient. By plotting the aforementioned time constants with regard to temperature in Arrhenius plots, the activation energies and cross sections of two families of traps responsible for the transients were extracted. Both trap families exhibit energies that are in close proximity to the mid-gap, situated at 40% and 60% above the valence band edge. The energies and cross sections are in accordance with the established literature on deep-level transient spectroscopy (DLTS). The measurements conducted at various wavelengths and photodiode polarizations, in conjunction with the diverse photodiode designs available on the array, led to the conclusion that the traps responsible for the transients are situated within the space charge region (SCR) of the HgCdTe photodiodes. It is our contention that this methodology could be employed as a standard diagnostic tool for the characterization of trap parameters within the SCR of photodiodes, as well as for the assessment of material quality at the ultimate stage of fabrication for an FPA using a DI ROIC.
- 11 August 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (10) , 8350-8362
Open AccessExtraction of Trap Parameters in HgCdTe P/N MWIR Focal Plane Arrays Using Photocurrent Transients Induced by Optical Excitation
Since their initial synthesis in 1958, HgCdTe compounds have been extensively developed as a highly effective material for infrared detection. The performance of these materials has improved continuously in terms of the first-order figures of merit, including dark current, quantum efficiency, and signal-to-noise ratio. Nowadays, the optimization of second-order performances is a key objective, with a particular focus on low-amplitude transients of photocurrents induced by scene illumination variation. In this study, we conducted measurements of photocurrent transients induced by optical excitation on HgCdTe mid-wave infrared (MWIR) focal plane arrays (FPAs). The HgCdTe detection circuit is flip-chipped onto a silicon direct injection readout integrated circuit (DI ROIC). The transients were measured at various temperatures, wavelengths, and levels of illumination. Furthermore, the bias of the photodiodes was varied in order to examine the impact of the space charge region extension. The FPA exhibits remarkably brief transients at operational temperatures (2.6 ms at 130 K) and low amplitudes relative to typical operational requirements. Two exponential regimes with two distinct time constants were identified in each transient. By plotting the aforementioned time constants with regard to temperature in Arrhenius plots, the activation energies and cross sections of two families of traps responsible for the transients were extracted. Both trap families exhibit energies that are in close proximity to the mid-gap, situated at 40% and 60% above the valence band edge. The energies and cross sections are in accordance with the established literature on deep-level transient spectroscopy (DLTS). The measurements conducted at various wavelengths and photodiode polarizations, in conjunction with the diverse photodiode designs available on the array, led to the conclusion that the traps responsible for the transients are situated within the space charge region (SCR) of the HgCdTe photodiodes. It is our contention that this methodology could be employed as a standard diagnostic tool for the characterization of trap parameters within the SCR of photodiodes, as well as for the assessment of material quality at the ultimate stage of fabrication for an FPA using a DI ROIC.
- Open Access
- 26 July 2024
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (10) , 5874-5884
The Tobin Coefficient: A Relevant Photodetector Performance Metric for IR Imaging
The well-known Rule07 is a simple thus efficient way to compare available technologies for IR imaging detectors in terms of dark current. The noise is then often estimated using a shot noise approximation on the dark current. Both II–VI and III–V communities use this rule of thumb as a reference for well-performing IR photodiodes. For HOT applications, a dark current close to this rule07 is considered a necessary condition but not a sufficient one to obtain a high-performance IR imager. Indeed, when limited by shot noise, rule07 describes well the noise behavior of the considered device. However, when considering low-frequency noise, it fails to describe the expected performances. In this paper, we focus on another figure-of-merit, dedicated to detector low-frequency noise rather than dark current. Systemic 1/f noise investigation in an IR detector was first reported by Tobin et al. in 1980. There is today a relative consensus on the fact that measured 1/f noise is proportional to the dark current. The ratio between the amplitude of the 1/f noise and the dark current of the same devices may therefore be used as a figure-of-merit for a given technology. This ratio (called the Tobin factor $${\alpha }_{\text{T}}$$ ) therefore appears adequate to compare different technologies as a figure-of-merit qualifying 1/f noise properties. This dimensionless ratio can also be very useful for optimizing a particular technology or process. However, in order to be relevant, this figure-of-merit must be estimated carefully as it appears, for instance, pixel pitch-dependent. Different examples of Tobin coefficient extraction are presented in this paper. We show that, depending on the technologies, the values of the Tobin coefficient can spread over several orders of magnitude. However, only low values result in high-quality IR imagers. Today, the best results we obtained show that $${\alpha }_{\text{T}}={10}^{-5}$$ is a state-of-art value to be compared with.- 26 July 2024
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 53 (10) , 5874-5884
Open AccessThe Tobin Coefficient: A Relevant Photodetector Performance Metric for IR Imaging
The well-known Rule07 is a simple thus efficient way to compare available technologies for IR imaging detectors in terms of dark current. The noise is then often estimated using a shot noise approximation on the dark current. Both II–VI and III–V communities use this rule of thumb as a reference for well-performing IR photodiodes. For HOT applications, a dark current close to this rule07 is considered a necessary condition but not a sufficient one to obtain a high-performance IR imager. Indeed, when limited by shot noise, rule07 describes well the noise behavior of the considered device. However, when considering low-frequency noise, it fails to describe the expected performances. In this paper, we focus on another figure-of-merit, dedicated to detector low-frequency noise rather than dark current. Systemic 1/f noise investigation in an IR detector was first reported by Tobin et al. in 1980. There is today a relative consensus on the fact that measured 1/f noise is proportional to the dark current. The ratio between the amplitude of the 1/f noise and the dark current of the same devices may therefore be used as a figure-of-merit for a given technology. This ratio (called the Tobin factor $${\alpha }_{\text{T}}$$ ) therefore appears adequate to compare different technologies as a figure-of-merit qualifying 1/f noise properties. This dimensionless ratio can also be very useful for optimizing a particular technology or process. However, in order to be relevant, this figure-of-merit must be estimated carefully as it appears, for instance, pixel pitch-dependent. Different examples of Tobin coefficient extraction are presented in this paper. We show that, depending on the technologies, the values of the Tobin coefficient can spread over several orders of magnitude. However, only low values result in high-quality IR imagers. Today, the best results we obtained show that $${\alpha }_{\text{T}}={10}^{-5}$$ is a state-of-art value to be compared with. - Open Access
Design and Characterization of 5 μm Pitch InGaAs Photodiodes Using In Situ Doping and Shallow Mesa Architecture for SWIR Sensing
This paper presents the complete design, fabrication, and characterization of a shallow-mesa photodiode for short-wave infra-red (SWIR) sensing. We characterized and demonstrated photodiodes collecting 1.55 μm photons with a pixel pitch as small as 3 μm. For a 5 μm pixel pitch photodiode, we measured the external quantum efficiency reaching as high as 54%. With substrate removal and an ideal anti-reflective coating, we estimated the internal quantum efficiency as achieving 77% at 1.55 μm. The best measured dark current density reached 5 nA/cm2 at −0.1 V and at 23 °C. The main contributors responsible for this dark current were investigated through the study of its evolution with temperature. We also highlight the importance of passivation with a perimetric contribution analysis and the correlation between MIS capacitance characterization and dark current performance.
Open AccessDesign and Characterization of 5 μm Pitch InGaAs Photodiodes Using In Situ Doping and Shallow Mesa Architecture for SWIR Sensing
This paper presents the complete design, fabrication, and characterization of a shallow-mesa photodiode for short-wave infra-red (SWIR) sensing. We characterized and demonstrated photodiodes collecting 1.55 μm photons with a pixel pitch as small as 3 μm. For a 5 μm pixel pitch photodiode, we measured the external quantum efficiency reaching as high as 54%. With substrate removal and an ideal anti-reflective coating, we estimated the internal quantum efficiency as achieving 77% at 1.55 μm. The best measured dark current density reached 5 nA/cm2 at −0.1 V and at 23 °C. The main contributors responsible for this dark current were investigated through the study of its evolution with temperature. We also highlight the importance of passivation with a perimetric contribution analysis and the correlation between MIS capacitance characterization and dark current performance.
- 16 June 2020
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (11) , 6900-6907
MTF Characterization of Small Pixel Pitch IR Cooled Photodiodes Using EBIC
- 16 June 2020
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (11) , 6900-6907
MTF Characterization of Small Pixel Pitch IR Cooled Photodiodes Using EBIC
- 11 June 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (8) , 5233-5240
HgCdTe Diode Dark Current Modeling: Rule 07 Revisited for LW and VLW
- 11 June 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (8) , 5233-5240
HgCdTe Diode Dark Current Modeling: Rule 07 Revisited for LW and VLW
- 10 August 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 47 (10) , 5680-5690
Shockley–Read–Hall Lifetime Study and Implication in HgCdTe Photodiodes for IR Detection
- 10 August 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 47 (10) , 5680-5690
Shockley–Read–Hall Lifetime Study and Implication in HgCdTe Photodiodes for IR Detection
- 14 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10624, 31
Achievement of high image quality MCT sensors with Sofradir vertical industrial model
SOFRADIR is the worldwide leader on the cooled IR detector market for high-performance space, military and security applications thanks to a well mastered Mercury Cadmium Telluride (MCT) technology, and recently thanks to the acquisition of III-V technology: InSb, InGaAs, and QWIP quantum detectors. This is the result of strong and continuous development efforts to deliver cutting edge products with improved performances in terms of spatial and thermal resolution, dark current, quantum efficiency, low excess noise and high operability. On one hand the advanced performances of Sofradir product rely on a strong partnership with CEA-LETI materialized in a common laboratory named DEFIR. On the other hand, these cutting edge performances are made possible thanks to Sofradir vertical industrial model. From the CdZnTe (CZT) and HgCdTe (MCT) crystal growth to the last electro-optical characterization recipe before shipping, and all the intermediate steps in between like IDDCA (Integrated Detector Dewar Cooler Assembly) final pumping cycle, all the manufacturing steps are developed, performed and controlled inhouse. This allows direct feedback between IDDCA, system performances and process or material. State of the art relevant performances for IR detection and imaging will be presented, that is to say low excess noise defects, RFPN (Residual Fixed Pattern Noise), NUC (Non Uniformity Correction) table stability for Daphnis product, 10μm pitch XGA extended MW matrix at 110K and HOT (High Operating Temperature) p-on-n technology, VGA format with 15μm pitch MW at 160K.
- 14 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10624, 31
Achievement of high image quality MCT sensors with Sofradir vertical industrial model
SOFRADIR is the worldwide leader on the cooled IR detector market for high-performance space, military and security applications thanks to a well mastered Mercury Cadmium Telluride (MCT) technology, and recently thanks to the acquisition of III-V technology: InSb, InGaAs, and QWIP quantum detectors. This is the result of strong and continuous development efforts to deliver cutting edge products with improved performances in terms of spatial and thermal resolution, dark current, quantum efficiency, low excess noise and high operability. On one hand the advanced performances of Sofradir product rely on a strong partnership with CEA-LETI materialized in a common laboratory named DEFIR. On the other hand, these cutting edge performances are made possible thanks to Sofradir vertical industrial model. From the CdZnTe (CZT) and HgCdTe (MCT) crystal growth to the last electro-optical characterization recipe before shipping, and all the intermediate steps in between like IDDCA (Integrated Detector Dewar Cooler Assembly) final pumping cycle, all the manufacturing steps are developed, performed and controlled inhouse. This allows direct feedback between IDDCA, system performances and process or material. State of the art relevant performances for IR detection and imaging will be presented, that is to say low excess noise defects, RFPN (Residual Fixed Pattern Noise), NUC (Non Uniformity Correction) table stability for Daphnis product, 10μm pitch XGA extended MW matrix at 110K and HOT (High Operating Temperature) p-on-n technology, VGA format with 15μm pitch MW at 160K.
- 17 November 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 206
Discussion about photodiode architectures for space applications
- 17 November 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 206
Discussion about photodiode architectures for space applications