Praveen Gunturi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Praveen Gunturi has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- David E. Kotecki
Department of Electrical and Computer Engineering, University of Maine, Orono, 04469, USA
5 shared publications Nuri W. Emanetoglu
Department of Electrical and Computer Engineering, University of Maine, Orono, ME, USA
1 shared publication
Latest Publications
- 23 July 2018
- Published by Springer Nature in Wireless Personal Communications
- Vol. 102 (1) , 437-448
Analysis and Implementation of a Gaussian Addition IR-UWB Transmitter for Increased Spectral Efficiency
- 23 July 2018
- Published by Springer Nature in Wireless Personal Communications
- Vol. 102 (1) , 437-448
Analysis and Implementation of a Gaussian Addition IR-UWB Transmitter for Increased Spectral Efficiency
- 5 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (11) , 4255-4265
A 250-Mb/s Data Rate IR-UWB Transmitter Using Current-Reused Technique
This paper describes the design, simulation, implementation and testing of an impulse-radio ultra-wideband bi-phase shift keying (IR-UWB BPSK) transmitter, working in the frequency range between 3.5 and 6.5 GHz. The transmitter has been optimized to achieve the maximum distance of transmission while working within the power limits specified by the Federal Communications Commission (FCC). In this transmitter, the IR-UWB signal is generated by differentiating a Gaussian signal and then amplifying the differentiated signal. This is accomplished using a current-reused power amplifier circuit as both the differentiator and amplifier. A theoretical analysis is performed to obtain the relationship between the output amplitude and the data rate of the transmitted signal. The simulations and experimental results of the IR-UWB BPSK transmitter, implemented in a 180-nm CMOS process, are then presented. The transmitter was found to function at data rates up to 250 Mb/s with a maximum peak amplitude of 0.5 V. The dc energy consumption of the transmitter is 86 pJ/pulse. The energy efficiency is 26.2% for the pulsewidth of 1 ns. The experimental results show that power spectral density of the transmitter agrees with the simulated results and is within the FCC limits. The total core area of the chip is 0.22 mm2.
- 5 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 65 (11) , 4255-4265
A 250-Mb/s Data Rate IR-UWB Transmitter Using Current-Reused Technique
This paper describes the design, simulation, implementation and testing of an impulse-radio ultra-wideband bi-phase shift keying (IR-UWB BPSK) transmitter, working in the frequency range between 3.5 and 6.5 GHz. The transmitter has been optimized to achieve the maximum distance of transmission while working within the power limits specified by the Federal Communications Commission (FCC). In this transmitter, the IR-UWB signal is generated by differentiating a Gaussian signal and then amplifying the differentiated signal. This is accomplished using a current-reused power amplifier circuit as both the differentiator and amplifier. A theoretical analysis is performed to obtain the relationship between the output amplitude and the data rate of the transmitted signal. The simulations and experimental results of the IR-UWB BPSK transmitter, implemented in a 180-nm CMOS process, are then presented. The transmitter was found to function at data rates up to 250 Mb/s with a maximum peak amplitude of 0.5 V. The dc energy consumption of the transmitter is 86 pJ/pulse. The energy efficiency is 26.2% for the pulsewidth of 1 ns. The experimental results show that power spectral density of the transmitter agrees with the simulated results and is within the FCC limits. The total core area of the chip is 0.22 mm2.
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483746,p. 1-4
A PA for MBOFDM-UWB and IR-UWB transmitters
This paper describes the design of 4.2 to 5.9 GHz CMOS power amplifier (PA) for applications in ultra-wideband (UWB) commuincations. The PA operates in the linear region over the input range of -12 dBm and delivers an output power of 6 dBm. The post layout simulations indicate the power added efficiency (PAE) is more than 35% at 5 GHz frequency and more than 20% between 4.2 GHz and 5.9 GHz. The input matching is realized by resistive feedback and the output and the interstage matching are realized using source degeneration inductors. The input and output reflection coefficients are less than -5 dB over the frequency from 4.2 GHz to 5.9 GHz. The PA can also be used in IR UWB transmitters and provides energy efficiency of 11.3%. The total chip area is approximately 0.7mm2 including electrostatic discharge (ESD) protection. The design is implemented in 180nm CMOS technology.
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483746,p. 1-4
A PA for MBOFDM-UWB and IR-UWB transmitters
This paper describes the design of 4.2 to 5.9 GHz CMOS power amplifier (PA) for applications in ultra-wideband (UWB) commuincations. The PA operates in the linear region over the input range of -12 dBm and delivers an output power of 6 dBm. The post layout simulations indicate the power added efficiency (PAE) is more than 35% at 5 GHz frequency and more than 20% between 4.2 GHz and 5.9 GHz. The input matching is realized by resistive feedback and the output and the interstage matching are realized using source degeneration inductors. The input and output reflection coefficients are less than -5 dB over the frequency from 4.2 GHz to 5.9 GHz. The PA can also be used in IR UWB transmitters and provides energy efficiency of 11.3%. The total chip area is approximately 0.7mm2 including electrostatic discharge (ESD) protection. The design is implemented in 180nm CMOS technology.
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483746,p. 1-4
IR-UWB BPK transmitter optimized for maximum distance of transmission
This paper describes the implementation of an Impulse-Radio Ultra-Wide-Band Bi-Phase Keying (IR-UWB BPK) transmitter which has been optimized to achieve the maximum distance of transmission while working within the power limits specified in FCC UWB specification. A theoretical analysis is performed to obtain the relationship between the output amplitude and data rate of the transmitted signal. The design is implemented in a 180nm CMOS process. The post-layout simulations, with extracted R, L and C parasitics, are presented. The output peak amplitude of the transmitter is 0.7 V at a maximum data rate of 700 Mbps. The total area of the chip is approximately 1mm2 including electrostatic discharge (ESD) diodes protection.
- 1 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483746,p. 1-4
IR-UWB BPK transmitter optimized for maximum distance of transmission
This paper describes the implementation of an Impulse-Radio Ultra-Wide-Band Bi-Phase Keying (IR-UWB BPK) transmitter which has been optimized to achieve the maximum distance of transmission while working within the power limits specified in FCC UWB specification. A theoretical analysis is performed to obtain the relationship between the output amplitude and data rate of the transmitted signal. The design is implemented in a 180nm CMOS process. The post-layout simulations, with extracted R, L and C parasitics, are presented. The output peak amplitude of the transmitter is 0.7 V at a maximum data rate of 700 Mbps. The total area of the chip is approximately 1mm2 including electrostatic discharge (ESD) diodes protection.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 733-736
Temperature and supply voltage insensitive OOK transmitter for UWB outdoor communications
Most of the literature on Ultra Wide Band (UWB) transmitters is focused on indoor communications. This paper presents the architecture of an Impulse Radio Ultra Wide Band (IR-UWB) transmitter for outdoor communications which complies with the FCC spectral limits. The transmitter consists of a pulse generator (PG) and a deriver circuit and has an operating frequency between 3.1 GHz and 6.4 GHz. The pulse output amplitude is ~ 700mV peak-to-peak into a 50Ω resistive load. The maximum data rate that can be achieved by the transmitter is 250Mbps at an overall power efficiency of 6.3%. The transmitter is compensated for voltage and temperature (VT) variations. The output pulse energy changes by less than 24% as the temperature varies from -55°C to 100°C, and by less than 5% as the supply voltage varies between 2.3 and 3.6V. The design is implemented in 180nm CMOS process and the simulation results with extracted R, L, C parasitics are presented.
- 1 August 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 733-736
Temperature and supply voltage insensitive OOK transmitter for UWB outdoor communications
Most of the literature on Ultra Wide Band (UWB) transmitters is focused on indoor communications. This paper presents the architecture of an Impulse Radio Ultra Wide Band (IR-UWB) transmitter for outdoor communications which complies with the FCC spectral limits. The transmitter consists of a pulse generator (PG) and a deriver circuit and has an operating frequency between 3.1 GHz and 6.4 GHz. The pulse output amplitude is ~ 700mV peak-to-peak into a 50Ω resistive load. The maximum data rate that can be achieved by the transmitter is 250Mbps at an overall power efficiency of 6.3%. The transmitter is compensated for voltage and temperature (VT) variations. The output pulse energy changes by less than 24% as the temperature varies from -55°C to 100°C, and by less than 5% as the supply voltage varies between 2.3 and 3.6V. The design is implemented in 180nm CMOS process and the simulation results with extracted R, L, C parasitics are presented.