XSXingyuan Shi

Xingyuan Shi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xingyuan Shi has a total of 122 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Monitoring the Onsets and Kinetics of β Phase Nucleation in Polydiarylfluorene Films Annealed at Different Temperatures

    by Chen Sun, Bin Liu, Xingyuan Shi, Aleksandr Perevedentsev, Israel Callejas‐Vidoy, Jaime J. Hernández Rueda, Isabel Rodriguez, Jinyi Lin, Wei Huang, Juan Cabanillas‐González

    Polydiarylfluorene stands out as a prime example of a conjugated polymer, renowned for its remarkable light‐emission properties and its capacity to form a distinct ordered crystalline phase—the β phase—with dramatic impact on the optoelectronic properties of this material. Despite extensive research on the morphology of this polymer, the initial stages of nucleation of polymer chains within β phase domains remain elusive. In this study, we investigate the β phase crystallization onset and evolution using a comprehensive set of structural and spectroscopic techniques. In particular, we probe the thermal onset for β phase nucleation by combining differential scanning calorimetry, grazing incidence wide‐angle X‐ray scattering, and absorption, photoluminescence, and Raman spectroscopies. Raman microscopy reveals that β domains are already emerging upon annealing at 210°C. Judicious control of β phase fraction is further shown to be essential for unlocking the optimal light‐emitting properties by amplified spontaneous emission analysis. Remarkably, triplet exciton diffusion probed via continuous‐wave photoinduced absorption spectroscopy uniquely provides definitive evidence for the presence of small, highly isolated β phase domains in films annealed at the lowest temperatures.

  • Open Access

    Perpendicular crossing chains enable high mobility in a noncrystalline conjugated polymer

    by Jack F. Coker, Stefania Moro, Anders S. Gertsen, Xingyuan Shi, Drew Pearce, Martin P. van der Schelling, Yucheng Xu, Weimin Zhang, Jens W. Andreasen, Chad R. Snyder, et al.

    The nature of interchain π-system contacts, and their relationship to hole transport, are elucidated for the high-mobility, noncrystalline conjugated polymer C16-IDTBT by the application of scanning tunneling microscopy, molecular dynamics, and quantum chemical calculations. The microstructure is shown to favor an unusual packing motif in which paired chains cross-over one another at near-perpendicular angles. By linking to mesoscale microstructural features, revealed by coarse-grained molecular dynamics and previous studies, and performing simulations of charge transport, it is demonstrated that the high mobility of C16-IDTBT can be explained by the promotion of a highly interconnected transport network, stemming from the adoption of perpendicular contacts at the nanoscale, in combination with fast intrachain transport.


  • Open Access

    Development of low-cost, compact chiroptical imaging systems

    by Matthew D. Ward, Ronan Docherty, Louis Minion, Xingyuan Shi, Kai Anson, Giuliano Siligardi, Jenny Nelson, Jessica Wade, Matthew J. Fuchter

    Real-time circularly polarised imaging is achieved using two low-cost (<£2000) and compact imaging systems controlled by open-source python software.


  • Open Access

    Structure–Property Relationships for the Electronic Applications of Bis-Adduct Isomers of Phenyl-C61 Butyric Acid Methyl Ester

    by Xueyan Hou, Jack F. Coker, Jun Yan, Xingyuan Shi, Mohammed Azzouzi, Flurin D. Eisner, James D. McGettrick, Sachetan M. Tuladhar, Isaac Abrahams, Jarvist M. Frost, et al.

    Higher adducts of a fullerene, such as the bis-adduct of PCBM (bis-PCBM), can be used to achieve shallower molecular orbital energy levels than, for example, PCBM or C-60. Substituting the bis-adduct for the parent fullerene is useful to increase the open-circuit voltage of organic solar cells or achieve better energy alignment as electron transport layers in, for example, perovskite solar cells. However, bis-PCBM is usually synthesized as a mixture of structural isomers, which can lead to both energetic and morphological disorder, negatively affecting device performance. Here, we present a comprehensive study on the molecular properties of 19 pure bis-isomers of PCBM using a variety of characterization methods, including ultraviolet photoelectron spectroscopy, thermal gravimetric analysis, differential scanning calorimetry, single crystal structure, and (time-dependent) density functional theory calculation. We find that the lowest unoccupied molecular orbital of such bis-isomers can be tuned to be up to 170 meV shallower than PCBM and up to 100 meV shallower than the mixture of unseparated isomers. The isolated bis-isomers also show an electron mobility in organic field-effect transistors of up to 4.5 x 10(-2) cm(2)/(V s), which is an order of magnitude higher than that of the mixture of bis-isomers. These properties enable the fabrication of the highest performing bis-PCBM organic solar cell to date, with the best device showing a power conversion efficiency of 7.2%. Interestingly, we find that the crystallinity of bis-isomers correlates negatively with electron mobility and organic solar cell device performance, which we relate to their molecular symmetry, with a lower symmetry leading to more amorphous bis-isomers, less energetic disorder, and higher dimensional electron transport. This work demonstrates the potential of side chain engineering for optimizing the performance of fullerene-based organic electronic devices.


  • Open Access

    Why Do Sulfone-Containing Polymer Photocatalysts Work So Well for Sacrificial Hydrogen Evolution from Water?

    by Sam A. J. Hillman, Reiner Sebastian Sprick, Drew Pearce, Duncan J. Woods, Wai-Yu Sit, Xingyuan Shi, Andrew I. Cooper, James R. Durrant, Jenny Nelson

    Many of the highest-performing polymer photocatalysts for sacrificial hydrogen evolution from water have contained dibenzo[b,d]thiophene sulfone units in their polymer backbones. However, the reasons behind the dominance of this building block are not well understood. We study films, dispersions, and solutions of a new set of solution-processable materials, where the sulfone content is systematically controlled, to understand how the sulfone unit affects the three key processes involved in photocatalytic hydrogen generation in this system: light absorption; transfer of the photogenerated hole to the hole scavenger triethylamine (TEA); and transfer of the photogenerated electron to the palladium metal co-catalyst that remains in the polymer from synthesis. Transient absorption spectroscopy and electrochemical measurements, combined with molecular dynamics and density functional theory simulations, show that the sulfone unit has two primary effects. On the picosecond timescale, it dictates the thermodynamics of hole transfer out of the polymer. The sulfone unit attracts water molecules such that the average permittivity experienced by the solvated polymer is increased. We show that TEA oxidation is only thermodynamically favorable above a certain permittivity threshold. On the microsecond timescale, we present experimental evidence that the sulfone unit acts as the electron transfer site out of the polymer, with the kinetics of electron extraction to palladium dictated by the ratio of photogenerated electrons to the number of sulfone units. For the highest-performing, sulfone-rich material, hydrogen evolution seems to be limited by the photogeneration rate of electrons rather than their extraction from the polymer.


  • Correction to “Highly Efficient Inverted Circularly Polarized Organic Light Emitting Diodes”

    by Li Wan, Jessica Wade, Xingyuan Shi, Shengda Xu, Matthew J. Fuchter, Alasdair J. Campbell


  • Open Access

    Relationship between molecular properties and degradation mechanisms of organic solar cells based on bis-adducts of phenyl-C61butyric acid methyl ester

    by Xueyan Hou, Andrew J. Clarke, Mohammed Azzouzi, Jun Yan, Flurin Eisner, Xingyuan Shi, Mark F. Wyatt, T. John S. Dennis, Zhe Li, Jenny Nelson

    Environmental stability remains a major challenge for the commercialisation of organic solar cells and degradation pathways remain poorly understood. Designing materials for improved device stability requires an understanding of the relationship between the properties of the donor or acceptor molecule and different degradation mechanisms. Here we study the correlations between various molecular parameters of the fullerene derivative bis-PCBM and the degradation rate of polymer:bis-PCBM organic solar cells, based on the same carbazole-alt-benzothiadiazole polymer, in aerobic and anaerobic conditions. We compare eight high purity bis-PCBM isomers with different electronic, chemical and packing properties along with PCBM and the mixture of bis isomers. In the case of aerobic photodegradation, we find that device degradation rate is positively correlated to the LUMO energy of the bis-PCBM isomer and to the degree of crystallinity of the isomer, while the correlation of degradation with driving force for epoxide formation is unclear. These results support the idea that in these samples, aerobic photodegradation proceeds via superoxide formation by the photogenerated polaron on the fullerene, followed by further chemical reaction. In the absence of air, photodegradation rate is correlated with molecular structure, supporting the mechanism of microstructural degradation via fullerene dimerization. The approach and findings presented here show how control of specific molecular parameters through chemical design can serve as a strategy to enhance stability of organic solar cells.


  • Open Access

    Highly Selective High‐Speed Circularly Polarized Photodiodes Based on π‐Conjugated Polymers

    by Matthew D. Ward, Jessica Wade, Xingyuan Shi, Jenny Nelson, Alasdair J. Campbell, Matthew J. Fuchter

    Chiral π‐conjugated molecular systems that are intrinsically sensitive to the handedness of circularly polarized (CP) light potentially allow for miniaturized, low‐cost CP detection devices. Such devices promise to transform several technologies, including biosensing, quantum optics, and communication of data encrypted by exploiting the spin angular momentum of light. Here a simple, bilayer organic photodiode (CP OPD) comprising an achiral π‐conjugated polymer–chiral additive blend as the electron donor layer and an achiral C60 electron acceptor layer is realized. These devices exhibit considerable photocurrent dissymmetry gph, with absolute values as high as 0.85 and dark currents as low as 10 pA. Impressively, they showcase a linear dynamic range of 80 dB, and rise and fall times of ≈7 µs, which significantly outperforms all previously reported CP selective photodetectors. Mechanistically, it is shown that the gph is sensitive to the thickness of both the chiral donor and achiral acceptor layers and that a trade‐off exists between the external quantum efficiency and gph. The fast‐switching speeds of these devices, coupled with their large dynamic range and highly selective response to CP light, opens up the possibility of their direct application in CP sensing and optical communications.


  • Open Access

    On the factors influencing the chiroptical response of conjugated polymer thin films

    by Beth Laidlaw, Julien Eng, Jessica Wade, Xingyuan Shi, Francesco Salerno, Matthew J. Fuchter, Thomas J. Penfold

    We study the influence of the physical and chemical structure on the chiroptical response of fluorene-based polymeric systems, namely poly(9,9-dioctylfluorene) (PFO) and the donor–acceptor type copolymer poly(9,9-dioctylfluorene-alt-benzothiadiazole) (F8BT). We reveal the significance of electric-magnetic coupling, at both short (molecular-level) and intermediate (delocalised over multiple polymer chains) length scales, on the magnitude of the dissymmetry. These findings provide a framework for the design of new materials with an enhanced chiroptical response.


  • Open Access

    Strongly Circularly Polarized Crystalline and β‐Phase Emission from Poly(9,9‐dioctylfluorene)‐Based Deep‐Blue Light‐Emitting Diodes

    by Li Wan, Xingyuan Shi, Jessica Wade, Alasdair J. Campbell, Matthew J. Fuchter

    A key challenge in the realization of circularly polarized polymer light‐emitting diodes (CP‐PLEDs) is the generation of highly circularly polarized deep‐blue electroluminescence (EL). Here, by blending the achiral luminescent polymer poly(9,9‐dioctylfluorene) (PFO) with a helically chiral molecule 1‐aza[6]helicene the authors present CP‐PLEDs with state‐of‐the‐art device performance for deep‐blue CP emission: for an inverted device with a semicrystalline microstructure a current efficiency (CE) of 1.13 cd A−1, a power efficiency (PE) of 0.81 lm W−1, and an EL dissymmetry (gEL) of −0.42 are achieved; for the planarized and extended “β‐phase” chain conformation a CE of 1.23 cd A−1, a PE of 0.63 lm W−1, and a gEL of −0.44 are achieved. While these two phases achieve both high CE, as well as gEL, the latter affords the first demonstration of chiral β‐phase emission from solid‐state PFO devices. Such strongly circularly polarized light is generated from a supramolecular assembly of interacting planar polymer backbones. The authors rationalize that the strong chiroptical effects observed within such chiral β‐phase PFO domains originate from coupled interchain aggregates. The findings not only demonstrate efficient deep‐blue CP‐PLEDs, but also provide insight into the mechanisms that underpin the strong CP emission from excitonically coupled polymer chains.