Francisco Lopez-Linares has a total of 100 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Discrimination of Allotropic Forms of Carbon by Laser-Induced Breakdown Spectroscopy (LIBS)

    by Dayana Oropeza, José Chirinos, Xianglei Mao, Alexander Kuperman, Jinyi Han, César Ovalles, Francisco López-Linares, Vassilia Zorba

  • Perspective on the Accelerated Mineralization Technology for Carbon Dioxide Capture, Utilization, and Storage

    by Ronald Marquez, Francisco Lopez-Linares, Greeshma Gadikota, Babak Fayyaz, Cesar Ovalles


  • Catalytic Conversion of Carbon Dioxide to Long Chain Esters via Formate Hydroesterification

    by Kyler Virtue, Babak Fayyaz, Francisco López‐Linares, Oleg Mironov, Cesar Ovalles, Wesley H. Bernskoetter

    CO2‐based hydroesterification is an attractive route to produce value added ester compounds, which could replace widely used CO‐based hydroesterification processes if sufficient catalytic technologies are developed. One path to CO2‐based hydroesterification could proceed through an organoformate intermediate, which is then used in olefin hydroesterification to generate the desirable esters. This route opens the possibility of creating a net CO2‐based hydroesterification process using tandem catalytic systems for CO2 hydrogenation to organoformate paired with formate‐olefin hydroesterification. The tandem use of tripodal phosphine ruthenium(II) and 1,2‐bis(di‐tert‐butylphosphinomethyl)benzene palladium catalysts were found to successfully produce methyl nonanoate from CO2, H2, methanol and 1‐octene in a single‐stage batch process. The CO2‐based hydroesterification catalysis efficiency was found to be largely limited by the productivity of organoformate generation and competitive 1‐octene reduction. Catalytic yields of methyl nonanoate can be enhanced by adjustments in reaction procedures, including the use of a two‐stage batch reaction process or delayed introduction of 1‐octene, achieving a yield of up to 32 %. Under select conditions, control experiments indicate yields of methyl nonanoate can be improved to ca 75 %. Preliminary studies indicate significant interplay between the two ligands employed in the molecular tandem catalytic systems and establish the first catalytic protocol for the selective CO2‐based hydroesterification of olefins via organoformates.


  • Perspective from the ACS Energy & Fuels Industry Committee toward the Transition to Sustainable Energy Sources

    by Ronald Marquez, Cesar Ovalles, Francisco Lopez-Linares, Wei Wang, Paul Robinson, Michael A. Reynolds

    This perspective from members of the Energy & Fuels Division (ENFL) Industry Committee of the American Chemical Society (ACS) discusses the ENFL’s role and challenges to foster a sustainable and equitable energy future by promoting research and technological advancements in energy production, storage, and utilization. Using bibliometric techniques, the current trends are presented in non-renewable and renewable energies, energy storage and grid modernization, hydrogen technologies, and carbon capture, utilization, and storage (CCUS). Recent International Energy Agency (IEA) projections indicate that 2023 global investments in clean energy increased by 17% to $1.7 trillion. However, conventional non-renewable sources still account for over 80% of global energy consumption, a share projected to peak near 2030. Continued robust growth in clean energy investments and capacity expansions in 2024 has shown solar photovoltaic (PV) and wind energy driving a substantial rise in renewable capacity. Nevertheless, conventional non-renewable sources still dominate global energy consumption. While renewable liquids from biomass remain limited, renewables are projected to supply only a modest fraction of the total energy demand by the decade’s end. Despite these trends and the practical limitations of producing renewable liquids from biomass, renewables are projected to account for 20% of final energy consumption by 2030, up from 13% in 2023. The importance of sustained investment in clean energy technologies and the adoption of innovative materials for energy applications is reflected in the ACS symposia during the spring and fall national meetings, which showcase novel applications and developments in these fields. We conclude by discussing how the ENFL continued efforts to foster interdisciplinary collaboration and support groundbreaking research can drive the energy and fuels sector toward more sustainable processes, an imperative for accelerating the global energy transition.


  • Open Access

    Application ICP-OES to Multielement Analysis on Plastic Waste and Blends with Vacuum Gas Oil: Developing a Sample Preparation Protocol

    by Laura Poirier, Hye-Kyung Timken, Francisco Lopez-Linares

    This paper introduces a new methodology for a routine metal analysis of plastic waste (PW) and PW blended with petroleum feedstock such as vacuum gas oil and VGO (PW/VGO). For such purposes, recycled polyethylene and polypropylene plastic were selected to mimic the potential feeds to be integrated at the Fluid Catalytic Cracking unit (FCC) to produce valuable products. Elements such as P, Ca, Al, Mg, Na, Zn, B, Fe, Ti, and Si were included in the method development. Different sample preparation methods were evaluated, such as microwave-assisted acid digestion (MWAD) and dry/wet ashing, followed by a fusion of the ash with lithium borate flux. Some PW homogenization pretreatments, such as cryogenic grinding and hot press molding, were also covered. The finding of this work suggests that MWAD with HNO3 and H2O2 is adequate for both types of samples and is the quickest sample preparation; however, the sample needed to be homogenized, and recoveries for Si and Ti may be biased for PW due to the limited solubilities of these elements in the nitric acid media. Carbon removal is required before fusion sample preparation and analysis due to the amount of carbon in PW samples. The sample needed to be homogenized for wet ash fusion but not for the pre-ash (dry) method. A benefit to the damp ash pretreatment is that the ash for the sample was created in the same crucible used for fusion digestion, avoiding material loss during sample management. Fusion from wet ash or carbon removal allowed for better acid solubility for Si and Ti in PW. The results of the PW samples evaluated matched well with those of both sample preparation methodologies. For most elements, precision was <10% regardless of the sample preparation; however, Fe and P had some variation using wet ash fusion, possibly due to contamination in an open digestion system or variation due to being close to the method limit of quantification (LOQ). The methodology reported here is robust enough to be implemented as routine analysis in any laboratory facility.


  • Characterization of nanoparticles used as precipitant agents for in situ upgrading of heavy crude oils via single particle inductively coupled plasma mass spectrometry (spICP-MS)

    by Deja Hebert, Yanila Salas-Ortiz, Jenny Nelson, Cesar Ovalles, Francisco Lopez-Linares, Estrella Rogel, Laura Poirier, Phoebe Zito


  • Open Access

    Elemental Mapping and Characterization of Petroleum-Rich Rock Samples by Laser-Induced Breakdown Spectroscopy (LIBS)

    by Charles Derrick Quarles, Toni Miao, Laura Poirier, Jhanis Jose Gonzalez, Francisco Lopez-Linares

    The application of Laser-Induced Breakdown Spectroscopy (LIBS) is presented for the direct elemental analysis of hydrocarbon-rich solids. In recent years, LIBS has become a powerful tool for obtaining elemental information and mapping analysis of different petroleum-rich samples with minimal to no sample preparation and without the need to separate the organic matter from the inorganic matter. By selecting the most intense and representative lines, the element distribution in a 2D map can be accessed in less than ten hours. For this reason, two types of hydrocarbon-rich solids were chosen for examination, i.e., core and shale. Nineteen elements were identified in the samples, and 2D mapping for Ca, Mg, Fe, Ti, Ni, C, H, K, O, and S is presented here. A detailed distribution of the elements, and the main components of the hydrocarbons present in these samples, were determined using LIBS. The H/C molar ratio was determined by building H and C calibration curves using data obtained from classical elemental analysis via combustion. These calibration curves contained a high degree of linearity (R2 > 0.98) with the limits of detection for C (193 nm), C (247 nm), and H (656 nm) of 848 mg kg−1, 353 mg kg−1, and 3.5 mg kg−1, respectively. By combining all of this information, LIBS allowed us to determine how these elements were spatially distributed, which elements were dominant in a given sample, and how much hydrocarbon was present, as well as providing a quantitative determination of the H/C molar ratio, and its correlation with the source of origin.


  • Open Access

    Analysis of gold nanoparticles in a hydrocarbon solvent by single particle-inductively coupled plasma mass spectrometry (spICP-MS) and TEM

    by Jenny Nelson, Aaron Saunders, Laura Poirier, Francisco Lopez-Linares

    Single-particle inductively coupled plasma mass spectrometry (spICP-MS) is used increasingly to characterize element-containing nanoparticles (NPs) in various samples, providing data on the number, concentration, size of particles, as well as the dissolved element concentration. Because there are currently only three examples of spICP-MS analysis of NPs in hydrocarbons in the literature. There is a clear need for hydrocarbon-based NP reference materials (RMs), available for analysts to develop and validate new methods. Here, an analysis of spICP-MS data is presented for two custom-developed gold NP RMs in toluene. The particle size data obtained by spICP-MS is compared with the total particle diameter obtained by transmission electron microscopy (TEM) and shows the excellent agreement among both techniques. Graphical abstract


  • Amphiphilic Thiol Polymer Nanogel Removes Environmentally Relevant Mercury Species from Both Produced Water and Hydrocarbons

    by Yilin Zhang, Garret D. Bland, Jiajun Yan, Astrid Avellan, Jiang Xu, Zongyu Wang, Thomas P. Hoelen, Francisco Lopez-Linares, Evan S. Hatakeyama, Krzysztof Matyjaszewski, et al.

    Technologies for removal of mercury from produced water and hydrocarbon phases are desired by oil and gas production facilities, oil refineries, and petrochemical plants. Herein, we synthesize and demonstrate the efficacy of an amphiphilic, thiol-abundant (11.8 wt % S, as thiol) polymer nanogel that can remove environmentally relevant mercury species from both produced water and the liquid hydrocarbon. The nanogel disperses in both aqueous and hydrocarbon phases. It has a high sorption affinity for dissolved Hg(II) complexes and Hg–dissolved organic matter complexes found in produced water and elemental (Hg0) and soluble Hg–alkyl thiol species found in hydrocarbons. X-ray absorption spectroscopy analysis indicates that the sorbed mercury is transformed to a surface-bound Hg(SR)2 species in both water and hydrocarbon regardless of its initial speciation. The nanogel had high affinity to native mercury species present in real produced water (>99.5% removal) and in natural gas condensate (>85% removal) samples, removing majority of the mercury species using only a 50 mg L–1 applied dose. This thiolated amphiphilic polymeric nanogel has significant potential to remove environmentally relevant mercury species from both water and hydrocarbon at low applied doses, outperforming reported sorbents like sulfur-impregnated activated carbons because of the mass of accessible thiol groups in the nanogel.