CCCatherine Chan

Catherine Chan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Catherine Chan has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Sustainability Impact of Different PV Mounting Systems and Pathways for Decarbonizing Emissions of PV Deployment

    by Sisi Wang, Moonyong Kim, Li Wang, Yuchao Zhang, Nathan Chang, Catherine Chan, Brett Hallam

    The amount of electricity generated by a solar panel varies according to the installation location and chosen mounting structure. This changes the effective material consumption and the associated effective carbon emissions of electricity produced by each solar panel. This article investigates the impact of different photovoltaic (PV) mounting systems on energy yield, material consumption, and carbon emissions, focusing on the key configurations of fixed-tilt (FT), east–west, and single-axis tracking systems. As global PV capacity rapidly expands, understanding the sustainability of these systems is crucial for decarbonizing the electricity sector. We highlight the impact of different mounting systems on yield at different latitudes and demonstrate that the effective material consumption can vary by over 30% in terms of both g/Wp and g/kWh, along with the impact on carbon emissions in terms of both gCO2-eq/Wp and gCO2-eq/kWh. Pathways to reduce the carbon footprint in gCO2-eq/kWh by up to 60% compared with the FT baseline case are also discussed, including incorporating green steel and decarbonized concrete.


  • Public Preferences for Water Allocation between Local Food Production and Protecting Watersheds in Hawai‘i

    by Rupananda Widanage, Catherine Chan

    Sustainable water allocation between local food production and protecting watershed health is a priority area in water resource planning in Hawai‘i. This paper employs the multinomial logit model to measure public preferences for water allocation and provides policy recommendations for formulating a sustainable agricultural water management policy. Estimated positive marginal willingness-to-pay (WTP) values of food self-sufficiency, watershed health, and biodiversity richness reflect public desire to invest in sustainable water management. Hence, stakeholder involvement at the watershed level is important for sustainable water management, as water is considered a public trust resource. The social cost of alternative water uses should be incorporated into water policy decisions on water allocation to preserve economic efficiency and ecological sustainability. Water policy and law in Hawai‘i account for social, economic, and ecological concerns in water resource management. This study integrates such concerns and the Public Trust Doctrine into water management policy decisions to benefit water users. Hence, the study findings are crucial for setting priorities in funding and making decisions regarding efficient water allocation for food production and protecting watersheds in Hawai‘i.


  • Open Access

    Review of Laser Doping and its Applications in Silicon Solar Cells

    by Michelle Vaqueiro-Contreras, Brett Hallam, Catherine Chan

    Laser-doped selective emitter diffusion techniques have become mainstream in solar cell manufacture covering 60% of the market share in 2022 and are expected to continue to grow to above 90% within the next five years (ITRPV). This was a very rapid uptake of technology, coming from only ∼10% penetration in 2018, and has enabled over 20 fA/cm 2 front recombination current reductions on the dominant passivated emitter and rear cell concepts in the same short period. In this article, a broad overview of key concepts in relation to laser doping methods relevant to solar cell manufacturing is given. We first discuss the basic mechanisms behind laser doping along with the benefits over conventional doping methods. The main laser doping approaches reported in the literature are then discussed, along with implications for metallization strategy, particularly in relation to selective emitter and back surface field formation in the dominant passivated emitter and rear cell technology. Different cell concepts that have benefited from the application of laser doping are also discussed. In the last section, we discuss the main defects induced by laser processing of silicon which affect the finished devices, potential and debated causes, as well as some commonly applied treatments for their mitigation.


  • Open Access

    Improved Laser-Induced Defect Passivation and Simultaneous Elimination of Light-Induced Degradation in p-Type Czochralski Silicon

    by Arman Mahboubi Soufiani, Anastasia Soeriyadi, Catherine Chan, Brett Hallam

    Laser doping is a typical industrial method to introduce a local highly doped region in silicon solar cells to form a selective emitter. Such a process inherently introduces defects that can be a concern to the overall performance of the solar cell. Here, we investigate the effectiveness of laser-induced defect (LasID) passivation on lifetime test structures through different annealing processes, including high-temperature belt-furnace firing, low-temperature belt-furnace annealing, and an advanced hydrogenation process (AHP) for n + laser-doped selective emitters. We demonstrate clear advantages of post treatment using a rapid 10 s AHP at 300 °C when the lifetime structures are prefired. For the examined laser speeds of 0.5–6 m/s (sheet resistances of 4--70 Ω/□), AHP is the most effective treatment method. For example, for a typical laser doping speed of 4 m/s, starting from the same effective carrier lifetime of 36.9±2.4 μs after laser-doping step for all the passivation treatments, the AHP not only surpasses the conventional approaches by showing the highest recovery of the effective carrier lifetime (∼79% compared with ∼63% and ∼41% for the firing and belt-furnace annealing treatments, respectively) and dark saturation current density reduction in the regions affected by LasIDs but also simultaneously suppresses light-induced degradation (maximum of 4% effective lifetime degradation with respect to the passivated state, as opposed to 14% and 16% degradation for the firing and belt-furnace annealing treatments, respectively) common in Cz grown boron-doped p-type monocrystalline silicon.


  • Open Access

    A case study on accelerated light‐ and elevated temperature‐induced degradation testing of commercial multi‐crystalline silicon passivated emitter and rear cell modules

    by Alison Ciesla, Moonyong Kim, Matthew Wright, Iskra Zafirovska, Daniel Chen, Brett Hallam, Catherine Chan

    Light‐ and elevated temperature‐induced degradation (LeTID) can have significant and long‐lasting effects on silicon photovoltaic modules. Its behaviour is complex, showing highly variable degradation under different conditions or due to minor changes in device fabrication. Here, we show the large difference in LeTID kinetics and extents in multi‐crystalline passivated emitter and rear cell (multi‐PERC) modules from four different manufacturers. Varied accelerated testing conditions are found to impact the maximum extent of degradation in different ways for different manufacturers complicating the ability to develop a universal predictive model for field degradation. Relative changes in the open‐circuit voltage (VOC) have previously been used to assess extents of LeTID; however, due to the greater impact of the defect at lower injection, the VOC is shown to degrade less than half as much as the voltage at maximum power point (VMPP). The MPP current (IMPP) and fill factor (FF) also degrade significantly, having an even larger overall impact on the power output. These observations imply that currently employed methodologies for testing LeTID are inadequate, which limits the reliability of future predictive models. In light of this, the field must develop a more holistic approach to analysing LeTID‐impacted modules, which incorporates information about changes under MPP conditions. This will allow for a much clearer understanding of LeTID in the field, which will assist the performance of future PV systems.


  • Impact of Substrate Thickness on the Degradation in Multicrystalline Silicon

    by Utkarshaa Varshney, Moonyong Kim, Muhammad Umair Khan, Phillip Hamer, Catherine Chan, Malcolm Abbott, Bram Hoex

    Light and elevated-temperature-induced degradation (LeTID) is a well-known phenomenon that reduces the bulk lifetime in silicon wafers. The cause of this degradation mechanism is still under investigation. However, a wide range of empirical trends that correlate LeTID with multiple physical and processing parameters have been reported, including the observation that wafers thinner than 120 μm do not show significant LeTID. In this work, we extend that study by varying the thickness of the wafers, the temperature of the firing step, and testing LeTID at the accelerated stability testing conditions. We demonstrate that the extent of degradation reduces with the thickness of the wafer, in agreement with the earlier work. However, silicon wafers with a thickness below 120 μm still suffer from LeTID when fired at sufficiently high temperatures, demonstrating that thinner wafers are not inherently immune to LeTID. By performing accelerated testing using a high-intensity laser and fitting the degradation and regeneration data, we observe that thinner wafers do not necessarily exhibit a faster recovery, as suggested earlier. However, their reduced degradation extent could be a consequence of relatively higher out-diffusion of hydrogen per unit volume in thinner wafers during firing. We further report that the method used for thinning the wafers results in a variation in the surface morphology of the samples, and that may partly be responsible for the observed correlation between the thickness of the wafers and LeTID extent. Finally, we discuss how these new findings can be explained by the involvement of hydrogen and other impurities in LeTID.


  • Open Access

    Progress in the understanding of light‐ and elevated temperature‐induced degradation in silicon solar cells: A review

    by Daniel Chen, Michelle Vaqueiro Contreras, Alison Ciesla, Phillip Hamer, Brett Hallam, Malcolm Abbott, Catherine Chan

    At present, the commercially dominant and rapidly expanding PV‐device technology is based on the passivated emitter and rear cell (PERC) design developed at UNSW. However, this technology has been found to suffer from a carrier‐induced degradation commonly referred to as ‘light‐ and elevated temperature‐induced degradation’ (LeTID) and can result in up to 16% relative performance losses. LeTID was recently shown to occur in almost every type of silicon wafer, independent of the doping material. Even though the degradation mechanism is known to recover under normal operation conditions, it is a lengthy process that drastically affects the energy yield, stability and, ultimately, the levelized cost of electricity (LCOE) of installed systems. Despite the joint effort of many research groups, the root cause of the degradation is still unknown. Here, we provide an overview of the existing literature and describe key LeTID characteristics and how these have led to the development of various theories of the underlying mechanism. Further, given the continuously appearing and strong evidence of hydrogen involvement in LeTID, many mitigation methods concerning hydrogenation have been suggested. We discuss such reported methods, bearing in mind crucial consumer necessities in terms of sustained cell performance and minimised LCOE.


  • Open Access

    Development of advanced hydrogenation processes for silicon solar cells via an improved understanding of the behaviour of hydrogen in silicon

    by Brett J. Hallam, Phill G. Hamer, Alison M. Ciesla Née Wenham, Catherine E. Chan, Bruno Vicari Stefani, Stuart Wenham

    The understanding and development of advanced hydrogenation processes for silicon solar cells are presented. Hydrogen passivation is incorporated into virtually all silicon solar cells, yet the properties of hydrogen in silicon are still poorly understood. This is largely due to the complex behaviour of hydrogen in silicon and its ability to exist in many different forms in the lattice. For commercial solar cells, hydrogen is introduced into the device through the deposition of hydrogen‐containing dielectric layers and the subsequent metallisation firing process. This process can readily passivate structural defects such as grain boundaries but is ineffective at passivating numerous defects in silicon solar cells such as the boron‐oxygen complex, responsible for light‐induced degradation in p‐type Czochralski silicon. This difficulty is due to the need to first form the boron‐oxygen defect and also due to atomic hydrogen naturally occupying low‐mobility and low‐reactivity charge states. However, these challenges can be overcome using advanced hydrogenation processes incorporating excess carrier generation from illumination or current injection that increase the concentration of the highly mobile and reactive neutral charge state. As a result, after fast firing, additional low‐temperature advanced hydrogenation processes incorporating illumination can be implemented to enable the passivation of difficult defects like the boron‐oxygen complex. With the implementation of such processes for industrial silicon solar cells, efficiency improvements of 1.1% absolute can be obtained.


  • Open Access

    Modeling Boron–Oxygen Degradation and Self-Repairing Silicon PV Modules in the Field

    by Alison M. Ciesla, Jose I. Bilbao, Catherine E. Chan, David N. R. Payne, Daniel Chen, Moonyong Kim, Stuart R. Wenham, Brett J. Hallam

    Photovoltaic (PV) cells manufactured using p-type Czochralski wafers can degrade significantly in the field due to boron–oxygen (BO) defects. Commercial hydrogenation processes can now passivate such defects; however, this passivation can be destabilized under certain conditions. Module operating temperatures are rarely considered in defect studies, and yet are critical to understanding the degradation and passivation destabilization that may occur in the field. Here we show that the module operating temperatures are highly dependent on location and mounting, and the impact this has on BO defects in the field. The System Advisor Model is fed with typical meteorological year data from four locations around the world (Hamburg, Sydney, Tucson, and Wuhan) to predict module operating temperatures. We investigate three PV system mounting types: building integrated (BIPV), rack-mounted rooftop, and rack mounted on flat ground for a centralized system. BO defect reactions are then simulated, using a three-state model based on experimental values published in the literature and the predicted module operating temperatures. The simulation shows that the BIPV module in Tucson reaches 94 °C and stays above 50 °C for over 1600 h per year. These conditions could destabilize over one-third of passivated BO defects, resulting in a 0.4% absolute efficiency loss for the modules in this work. This absolute efficiency loss could be double for higher efficiency solar cell structures, and modules. On the other hand, passivation of BO defects can occur in the field if hydrogen is present and the module is under the right environmental conditions. It is therefore important to consider the specific installation location and type (or predicted operating temperatures) to determine the best way to treat BO defects. Modules that experience such extreme sustained conditions should be manufactured to ensure incorporation of hydrogen to enable passivation of BO defects in the field, thereby enabling a “self-repairing module.”


  • Controlling Light- and Elevated-Temperature-Induced Degradation With Thin Film Barrier Layers

    by Utkarshaa Varshney, Brett Hallam, Phillip Hamer, Alison Ciesla, Daniel Chen, Shaoyang Liu, Chandany Sen, Aref Samadi, Malcolm Abbott, Catherine Chan, et al.

    In this article, we investigate the extent of lifetime degradation attributed to light- and elevated-temperature-induced degradation (LeTID) in p-type multicrystalline silicon wafers passivated with different configurations of hydrogenated silicon nitride (SiN $_\text{x}$ :H) and aluminum oxide (AlO $_\text{x}$ :H). We also demonstrate a significant difference between AlO $_\text{x}$ :H layers grown by atomic layer deposition (ALD) and plasma-enhanced chemical vapor deposition (PECVD) with respect to the extent of LeTID. When ALD AlO $_\text{x}$ :H is placed underneath a PECVD SiN $_\text{x}$ :H layer, as used in a passivated emitter and rear solar cell, a lower extent of LeTID is observed compared with the case when a single PECVD SiN $_\text{x}$ :H layer is used. On the other hand, the LeTID extent is significantly increased when an ALD AlO $_\text{x}$ :H is grown on top of the PECVD SiN $_\text{x}$ :H film. Remarkably, when a PECVD AlO $_\text{x}$ :H is used underneath the PECVD SiN $_\text{x}$ :H film, an increase in the LeTID extent is observed. Building on our current understanding of LeTID, we explain these results with the role of ALD AlO $_\text{x}$ :H in impeding the hydrogen diffusion from the dielectric stack into the c-Si bulk, while PECVD AlO $_\text{x}$ :H seems to act as an additional hydrogen source. These observations support the hypothesis that hydrogen is playing a key role in LeTID and provide solar cell manufacturers with a new method to reduce LeTID in their solar cells.