Hamid Oveisi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hamid Oveisi has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Amin Imani
Department of Materials Engineering, The University of British Columbia, Vancouver, Canada
2 shared publications Azadeh Meshkini
2 shared publications- Hamid Hosseinzadeh
Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
2 shared publications Abdulmohsen Ali Alshehri
Department of Chemistry, King Abdulaziz University, P.O. Box 80203, Jeddah 21589, Saudi Arabia
1 shared publication- Azadeh Meshkini
Department of Chemistry, Faculty of Science, Ferdowsi University of Mashhad, Mashhad 9177948974, Iran
1 shared publication Fatemeh Jalali
Department of Materials and Polymer Engineering, Hakim Sabzevari University, Sabzevar, Iran
1 shared publication
Latest Publications
- 9 October 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (42) , 20160-20190
Review: Enhancing dielectric polymer performance via inorganic fillers
- 9 October 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (42) , 20160-20190
Review: Enhancing dielectric polymer performance via inorganic fillers
- 9 July 2025
- Published by SAGE Publications in Advances in Applied Ceramics: Structural, Functional and Bioceramics
- Vol. 124 (3-5) , 78-90
Gadolinium-doped CoFe 2 O 4 semi-crystalline nanoparticles with designed morphology: The effect of synthesis parameters on microstructure and magnetic characteristics
In this study, the CoFe 2 O 4 nanoparticles were synthesised hydrothermally (70–200 °C) with various molar ratios of CoCl 2 /FeCl 3 for desirable nanoparticle shape and properties. The atomic ratios of gadolinium (Gd) were increased to 0.70 to investigate the effect of the Gd dopant. The X-ray diffraction patterns indicated that by increasing the synthesis temperature (70–200 °C), the nanoparticle size decreased from 50.49 nm to 32.45 nm, and the morphology changed from a shapeless and agglomerated state to a spherical shape. The M s value increased from 17.253 emu/g to 54.438 emu/g with a rise in the synthesis temperature. The effects of the FeCl 3 / CoCl 2 molar ratio showed the highest value of M s (54.438 emu/g) and the coercivity of 744.56 Oe for a 2/1 molar ratio. The X-ray photoelectron spectroscopy illustrated several peaks corresponding to Fe 3+ , Co 2 + and O 1. This study aimed to investigate the possibility of utilising CoFe 2−x Gd x O 4 nanoparticles for medical treatment.
- 9 July 2025
- Published by SAGE Publications in Advances in Applied Ceramics: Structural, Functional and Bioceramics
- Vol. 124 (3-5) , 78-90
Gadolinium-doped CoFe 2 O 4 semi-crystalline nanoparticles with designed morphology: The effect of synthesis parameters on microstructure and magnetic characteristics
In this study, the CoFe 2 O 4 nanoparticles were synthesised hydrothermally (70–200 °C) with various molar ratios of CoCl 2 /FeCl 3 for desirable nanoparticle shape and properties. The atomic ratios of gadolinium (Gd) were increased to 0.70 to investigate the effect of the Gd dopant. The X-ray diffraction patterns indicated that by increasing the synthesis temperature (70–200 °C), the nanoparticle size decreased from 50.49 nm to 32.45 nm, and the morphology changed from a shapeless and agglomerated state to a spherical shape. The M s value increased from 17.253 emu/g to 54.438 emu/g with a rise in the synthesis temperature. The effects of the FeCl 3 / CoCl 2 molar ratio showed the highest value of M s (54.438 emu/g) and the coercivity of 744.56 Oe for a 2/1 molar ratio. The X-ray photoelectron spectroscopy illustrated several peaks corresponding to Fe 3+ , Co 2 + and O 1. This study aimed to investigate the possibility of utilising CoFe 2−x Gd x O 4 nanoparticles for medical treatment.
- 10 January 2025
- Published by Wiley in ChemistrySelect
- Vol. 10 (2)
Template‐Free Synthesis of Mesoporous Iron‐Nickel‐Cobalt Oxide Microspheres via Ultrasonic Spray Pyrolysis Across Temperature Gradients for Enhanced Visible Light Photocatalytic Activity
This study explores the synthesis of template‐free mesoporous FeNiCo oxide microspheres through a direct and efficient ultrasonic spray pyrolysis (USP) technique. USP method includes precise control over particle size, the formation of mesoporous structures, multimetallic compositions, and high synthesis speed, all of which can contribute to enhanced photocatalytic activity. The analysis of the resulting microspheres involved a thorough exploration of their phase structure, texture, morphology, and photocatalytic properties. This investigation employed various analytical techniques, including X‐ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and nitrogen adsorption−desorption. The microspheres displayed a well‐crystallized cubic crystal structure, as evidenced by the X‐ray diffraction pattern, with a corresponding crystallite size ranging from 6.0 to 7.4 nm. The FESEM images revealed the synthesis of uniform‐sized particles with spherical shapes. N 2 adsorption and desorption highlighted the mesoporous structure of FeNiCo oxide microspheres, indicating diverse surface areas and pore distributions, influencing catalytic performance and dye adsorption. The capability of the synthesized photocatalysts to degrade methylene blue was examined under both UV and visible light irradiation. The FeNiCo oxide microspheres exhibited a band gap of 2.34 eV. Photocatalytic evaluation revealed that the FeNiCo oxide nanoparticles achieved a 65% degradation of methylene blue within 110 min.
- 10 January 2025
- Published by Wiley in ChemistrySelect
- Vol. 10 (2)
Template‐Free Synthesis of Mesoporous Iron‐Nickel‐Cobalt Oxide Microspheres via Ultrasonic Spray Pyrolysis Across Temperature Gradients for Enhanced Visible Light Photocatalytic Activity
This study explores the synthesis of template‐free mesoporous FeNiCo oxide microspheres through a direct and efficient ultrasonic spray pyrolysis (USP) technique. USP method includes precise control over particle size, the formation of mesoporous structures, multimetallic compositions, and high synthesis speed, all of which can contribute to enhanced photocatalytic activity. The analysis of the resulting microspheres involved a thorough exploration of their phase structure, texture, morphology, and photocatalytic properties. This investigation employed various analytical techniques, including X‐ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and nitrogen adsorption−desorption. The microspheres displayed a well‐crystallized cubic crystal structure, as evidenced by the X‐ray diffraction pattern, with a corresponding crystallite size ranging from 6.0 to 7.4 nm. The FESEM images revealed the synthesis of uniform‐sized particles with spherical shapes. N 2 adsorption and desorption highlighted the mesoporous structure of FeNiCo oxide microspheres, indicating diverse surface areas and pore distributions, influencing catalytic performance and dye adsorption. The capability of the synthesized photocatalysts to degrade methylene blue was examined under both UV and visible light irradiation. The FeNiCo oxide microspheres exhibited a band gap of 2.34 eV. Photocatalytic evaluation revealed that the FeNiCo oxide nanoparticles achieved a 65% degradation of methylene blue within 110 min.
- Open Access
Structural basis for the simultaneous recognition of NEMO and acceptor ubiquitin by the HOIP NZF1 domain
Summary: Ubiquitination of NEMO by the linear ubiquitin chain assembly complex (LUBAC) is essential for activating the canonical NF-κB signaling pathway. While the NZF1 domain of the HOIP subunit of LUBAC recognizes the NEMO substrate, it is unclear how it cooperates with the catalytic domains in the ubiquitination process. Here, we report a crystal structure of NEMO in complex with HOIP NZF1 and linear diubiquitin chains, in which the two proteins bind to distinct sites on NEMO. Moreover, the NZF1 domain simultaneously interacts with NEMO and Ile44 surface of a proximal ubiquitin from a linear diubiquitin chain, where the C-term tail of the ubiquitin is in the proximity of the NEMO ubiquitination site (Lys285). We further propose a model for the linear ubiquitination of NEMO by HOIP. In the model, NZF1 binds the monoubiquitinated NEMO and recruits the catalytic domains to the ubiquitination site, thereby ensuring site-specific ubiquitination of NEMO.
Open AccessStructural basis for the simultaneous recognition of NEMO and acceptor ubiquitin by the HOIP NZF1 domain
Summary: Ubiquitination of NEMO by the linear ubiquitin chain assembly complex (LUBAC) is essential for activating the canonical NF-κB signaling pathway. While the NZF1 domain of the HOIP subunit of LUBAC recognizes the NEMO substrate, it is unclear how it cooperates with the catalytic domains in the ubiquitination process. Here, we report a crystal structure of NEMO in complex with HOIP NZF1 and linear diubiquitin chains, in which the two proteins bind to distinct sites on NEMO. Moreover, the NZF1 domain simultaneously interacts with NEMO and Ile44 surface of a proximal ubiquitin from a linear diubiquitin chain, where the C-term tail of the ubiquitin is in the proximity of the NEMO ubiquitination site (Lys285). We further propose a model for the linear ubiquitination of NEMO by HOIP. In the model, NZF1 binds the monoubiquitinated NEMO and recruits the catalytic domains to the ubiquitination site, thereby ensuring site-specific ubiquitination of NEMO.
- Open Access
- 14 January 2022
- Published by Springer Nature in Research Square
Synthesis Factors Dependence of Magnetic Properties of CoFe2O4 and CoFe2-xGdxO4 Semicrystalline Nanoparticles with desired Morphology through Hydrothermal Procedure
In the present study, CoFe2O4 and CoFe2-xGdxO4 nanoparticles were synthesized by the hydrothermal process. The CoFe2O4 nanoparticles were synthesized at different temperatures (70oC, 100oC, 150oC, and 200oC), molar ratio of CoCl2/ FeCl3 (0/2, 0.75/2, 1/2, 1.5/2, and 2/2). Gadolinium-doped cobalt ferrite (CoFe2-xGdxO4) nanoparticles have also been synthesized with Gd/Fe molar ratios of 0.18 and 0.53. The XRD patterns indicate that cobalt ferrite and Gadolinium-doped cobalt ferrite nanoparticles have been successfully synthesized without impurities with a medium degree of crystallinity. The XRD patterns show that by increasing the synthesis temperature from 70oC to 200oC, the size of the nanoparticles decreased from 50.49nm to 32.45nm while the morphology of the nanoparticles also changed from a shapeless and agglomerated state to a spherical shape. The XPS curve illustrated several peaks corresponding to Fe+3, Co+2, and O 1s. The binding energies for Co and Fe were consistent with Fe 2p and Co 2p binding energies for cobalt ferrite nanoparticles. The magnetic saturation value (Ms) increased from 17.253 emu/g to 54.438 emu/g with a rise in the synthesis temperature. The effects of FeCl3/CoCl2 molar ratio on the magnetic properties showed the highest value of Ms (54.438 emu/g) and the coercivity (HC) of 744.56 Oe for a 2/1 molar ratio. The addition of gadolinium to the composition resulted in a reducing of the magnetic properties of nanoparticles; accordingly, the amount of saturated magnetization was reduced to 22.469 emu/g. Another effect of gadolinium dopant in the composition was a change in nanoparticle morphology from spherical to rod shape. The final aim of this study was to investigate the possible utilization of CoFe2O4 and CoFe2-xGdxO4 nanoparticles in medical treatment in the near future.
- 14 January 2022
- Published by Springer Nature in Research Square
Open AccessSynthesis Factors Dependence of Magnetic Properties of CoFe2O4 and CoFe2-xGdxO4 Semicrystalline Nanoparticles with desired Morphology through Hydrothermal Procedure
In the present study, CoFe2O4 and CoFe2-xGdxO4 nanoparticles were synthesized by the hydrothermal process. The CoFe2O4 nanoparticles were synthesized at different temperatures (70oC, 100oC, 150oC, and 200oC), molar ratio of CoCl2/ FeCl3 (0/2, 0.75/2, 1/2, 1.5/2, and 2/2). Gadolinium-doped cobalt ferrite (CoFe2-xGdxO4) nanoparticles have also been synthesized with Gd/Fe molar ratios of 0.18 and 0.53. The XRD patterns indicate that cobalt ferrite and Gadolinium-doped cobalt ferrite nanoparticles have been successfully synthesized without impurities with a medium degree of crystallinity. The XRD patterns show that by increasing the synthesis temperature from 70oC to 200oC, the size of the nanoparticles decreased from 50.49nm to 32.45nm while the morphology of the nanoparticles also changed from a shapeless and agglomerated state to a spherical shape. The XPS curve illustrated several peaks corresponding to Fe+3, Co+2, and O 1s. The binding energies for Co and Fe were consistent with Fe 2p and Co 2p binding energies for cobalt ferrite nanoparticles. The magnetic saturation value (Ms) increased from 17.253 emu/g to 54.438 emu/g with a rise in the synthesis temperature. The effects of FeCl3/CoCl2 molar ratio on the magnetic properties showed the highest value of Ms (54.438 emu/g) and the coercivity (HC) of 744.56 Oe for a 2/1 molar ratio. The addition of gadolinium to the composition resulted in a reducing of the magnetic properties of nanoparticles; accordingly, the amount of saturated magnetization was reduced to 22.469 emu/g. Another effect of gadolinium dopant in the composition was a change in nanoparticle morphology from spherical to rod shape. The final aim of this study was to investigate the possible utilization of CoFe2O4 and CoFe2-xGdxO4 nanoparticles in medical treatment in the near future.
- 28 November 2020
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 31 (12) , 1-15
Enhanced osteogenesis properties of titanium implant materials by highly uniform mesoporous thin films of hydroxyapatite and titania intermediate layer
Titanium (Ti) has been widely used for medical and dental applications; however, bare Ti cannot be properly connected to a living bone, and hence some modifications are needed for this purpose. The present study describes the synthesis of mesoporous hydroxyapatite thin films (MHF) on titanium implant materials for speeding up and shortening the processes of osteointegration. The uniform MHF was coated on a Ti substrate following the insertion of intermediate titania (TiO2) film via the sol–gel dip-coating method. The intermediate titania layer improved the bonding strength between the MHF and Ti substrate. MHFs were synthesized using a precursor solution containing phosphoric acid, calcium nitrate tetrahydrate, and a nonionic surfactant (C12E10) as the phosphate source, calcium source, and structure-directing agent, respectively. The effect of calcination temperature on phase composition, morphology, microstructure, roughness, and wettability of the MHFs was investigated using XRD, FE-SEM, COM, AFM, and contact angle measurement. The XRD results revealed the crystalline hydroxyapatite phase, which was improved with an increase in the calcination temperature. Moreover, the FE-SEM images showed the crack-free MHFs, uniform thickness of the layer, and mesoporous surface morphology. In addition, it was found that the roughness and wettability of the samples change upon the alteration of calcination temperature. The biological studies demonstrated that MHFs support the adhesion and proliferation of the mesenchymal stem cells (MSCs) and guid them toward osteogenic differentiation. Therefore, the MHFs prepared in this study may be useful in a wide range of applications, particularly in bone regeneration medicine.
- 28 November 2020
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 31 (12) , 1-15
Enhanced osteogenesis properties of titanium implant materials by highly uniform mesoporous thin films of hydroxyapatite and titania intermediate layer
Titanium (Ti) has been widely used for medical and dental applications; however, bare Ti cannot be properly connected to a living bone, and hence some modifications are needed for this purpose. The present study describes the synthesis of mesoporous hydroxyapatite thin films (MHF) on titanium implant materials for speeding up and shortening the processes of osteointegration. The uniform MHF was coated on a Ti substrate following the insertion of intermediate titania (TiO2) film via the sol–gel dip-coating method. The intermediate titania layer improved the bonding strength between the MHF and Ti substrate. MHFs were synthesized using a precursor solution containing phosphoric acid, calcium nitrate tetrahydrate, and a nonionic surfactant (C12E10) as the phosphate source, calcium source, and structure-directing agent, respectively. The effect of calcination temperature on phase composition, morphology, microstructure, roughness, and wettability of the MHFs was investigated using XRD, FE-SEM, COM, AFM, and contact angle measurement. The XRD results revealed the crystalline hydroxyapatite phase, which was improved with an increase in the calcination temperature. Moreover, the FE-SEM images showed the crack-free MHFs, uniform thickness of the layer, and mesoporous surface morphology. In addition, it was found that the roughness and wettability of the samples change upon the alteration of calcination temperature. The biological studies demonstrated that MHFs support the adhesion and proliferation of the mesenchymal stem cells (MSCs) and guid them toward osteogenic differentiation. Therefore, the MHFs prepared in this study may be useful in a wide range of applications, particularly in bone regeneration medicine.
- Open Access
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016549
High porosity micro- and macro-cellular copper foams with semi-open cell microstructure toward its physical and mechanical properties
Herein, a powder compacting method was developed to fabricate high porosity micro- and macro-cellular copper foams using CaCO3 space holder. The cold compacted precursors were heated at different temperatures under the nitrogen atmosphere. The effects of precursor compaction pressure, space holder content and sintering temperature on cell microstructure, relative density, compressive and physical properties were investigated. The scanning electron microscopy (SEM) images showed a uniform distribution of interconnected pores with sizes of pores and channels less than 50 microns formed the semi-open cell structure of the fabricated foams. The evaluation of the foaming agent content, 0 to 20 (wt%), in precursor materials showed relatively large changes in the porosity percentage (27%–50%), with the utilitarian strength (43 MPa) and densification strain (40%) of the copper foams. For specimens having 20 wt% CaCO3, tuning the sintering temperature (600 °C) and compacting pressure (500 MPa) of precursors tailored superior porosity percent (47%), remarkable compressive stress (501 MPa) and high thermal (43.8 W m−1.k), and electrical conductivity (0.06 × 10 8 Ω−1 m−1) owing to a desirable foaming process. A massive gas release during the CaCO3 decomposition and the strengthened cell walls of the copper foams during the sintering resulted in the high porosity and strength of the fabricated foams. The presented fabrication method and our results are the core elements for the development of new high porosity metal foams that can help the development of the future application of copper foams for a long-life anode for lithium-ion batteries, catalysis, and thermal and electrical performances as electronic cooling materials.
- 1 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (1) , 016549
Open AccessHigh porosity micro- and macro-cellular copper foams with semi-open cell microstructure toward its physical and mechanical properties
Herein, a powder compacting method was developed to fabricate high porosity micro- and macro-cellular copper foams using CaCO3 space holder. The cold compacted precursors were heated at different temperatures under the nitrogen atmosphere. The effects of precursor compaction pressure, space holder content and sintering temperature on cell microstructure, relative density, compressive and physical properties were investigated. The scanning electron microscopy (SEM) images showed a uniform distribution of interconnected pores with sizes of pores and channels less than 50 microns formed the semi-open cell structure of the fabricated foams. The evaluation of the foaming agent content, 0 to 20 (wt%), in precursor materials showed relatively large changes in the porosity percentage (27%–50%), with the utilitarian strength (43 MPa) and densification strain (40%) of the copper foams. For specimens having 20 wt% CaCO3, tuning the sintering temperature (600 °C) and compacting pressure (500 MPa) of precursors tailored superior porosity percent (47%), remarkable compressive stress (501 MPa) and high thermal (43.8 W m−1.k), and electrical conductivity (0.06 × 10 8 Ω−1 m−1) owing to a desirable foaming process. A massive gas release during the CaCO3 decomposition and the strengthened cell walls of the copper foams during the sintering resulted in the high porosity and strength of the fabricated foams. The presented fabrication method and our results are the core elements for the development of new high porosity metal foams that can help the development of the future application of copper foams for a long-life anode for lithium-ion batteries, catalysis, and thermal and electrical performances as electronic cooling materials.
- 17 December 2019
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 108 (4) , 882-894
Meso‐macroporous crack‐free nanohydroxyapatite coatings templated by C12E10 diblock copolymer on Ti6Al4V implant materials toward human osteoblast‐like cells
Meso‐macroporous nanohydroxyapatite coatings (MHACs) were synthesized on Ti6Al4V implant materials calcined at different temperatures using a nonionic diblock copolymer template (C12E10) by sol–gel and dip‐coating methods. To improve the bonding strength between the substrate and coating, a TiO2 intermediate layer was applied on the surface of the substrates. The physicochemical and structural properties of MHAC samples were fully studied by X‐ray diffraction, X‐ray photoelectron spectroscopy, Fourier‐transform infrared spectroscopy, scanning probe microscopy, field‐emission scanning electron microscopy (FESEM), Brunauer–Emmett–Teller method, and contact angle measurements. Based on the data obtained, the hydroxyapatite phase with a flower‐like morphology was formed on the Ti6Al4V substrates in all of the samples. According to confocal optical microscopy and FESEM images, there was no macrocrack and microcrack on the MHACs, whereas they were accompanied by macroporosities and mesoporosities on top of the coatings. By increasing the calcination temperature from 500°C to 650°C, the crystallite sizes increased, while the surface roughness value and hydrophilicity decreased. A reduction in specific surface area and an increase in the pore diameters occurred as the calcination temperature increased. In addition, the assessment of protein adsorption behavior over the samples revealed that the adsorption amounts significantly increased as the substrates were coated with HAP; however, the affinity of surface for protein adsorption was strictly dependent on the surface topography and hydrophilicity. in vitro cellular assay disclosed a great cytocompatibility in terms of adhesion and proliferation in MHAC samples as compared with that in TiO2‐coated and bare substrates. Regarding the physicochemical properties and biological studies, MHAC calcined at 650°C was deemed optimal for bone tissue engineering.
- 17 December 2019
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 108 (4) , 882-894
Meso‐macroporous crack‐free nanohydroxyapatite coatings templated by C12E10 diblock copolymer on Ti6Al4V implant materials toward human osteoblast‐like cells
Meso‐macroporous nanohydroxyapatite coatings (MHACs) were synthesized on Ti6Al4V implant materials calcined at different temperatures using a nonionic diblock copolymer template (C12E10) by sol–gel and dip‐coating methods. To improve the bonding strength between the substrate and coating, a TiO2 intermediate layer was applied on the surface of the substrates. The physicochemical and structural properties of MHAC samples were fully studied by X‐ray diffraction, X‐ray photoelectron spectroscopy, Fourier‐transform infrared spectroscopy, scanning probe microscopy, field‐emission scanning electron microscopy (FESEM), Brunauer–Emmett–Teller method, and contact angle measurements. Based on the data obtained, the hydroxyapatite phase with a flower‐like morphology was formed on the Ti6Al4V substrates in all of the samples. According to confocal optical microscopy and FESEM images, there was no macrocrack and microcrack on the MHACs, whereas they were accompanied by macroporosities and mesoporosities on top of the coatings. By increasing the calcination temperature from 500°C to 650°C, the crystallite sizes increased, while the surface roughness value and hydrophilicity decreased. A reduction in specific surface area and an increase in the pore diameters occurred as the calcination temperature increased. In addition, the assessment of protein adsorption behavior over the samples revealed that the adsorption amounts significantly increased as the substrates were coated with HAP; however, the affinity of surface for protein adsorption was strictly dependent on the surface topography and hydrophilicity. in vitro cellular assay disclosed a great cytocompatibility in terms of adhesion and proliferation in MHAC samples as compared with that in TiO2‐coated and bare substrates. Regarding the physicochemical properties and biological studies, MHAC calcined at 650°C was deemed optimal for bone tissue engineering.