Jinwen He
Research Subjects
Jinwen He has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Guo Ming Liu
Fuzhou University
1 shared publicationLanhao Zhao
College of Water Conservancy and Hydropower, Hohai University, Nanjing 210098, China
1 shared publication- Ping Zhang
College of Hydraulic & Environmental Engineering China ree Gorges University 443002 Yichang Hubei China
1 shared publication - Tongchun Li
College of Water Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China
1 shared publication Wen Qiao
Fuzhou University
1 shared publicationXiaona Li
College of Water Conservancy and Hydropower, Hohai University, Nanjing 210098, China
1 shared publication
Latest Publications
- Open Access
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Reliability Analysis for Bypass Seepage Stability of Complex Reinforced Earth‐Rockfill Dam with High‐Order Practical Stochastic Response Surface Method
Practical stochastic response surface method (SRSM) using ordinary high‐order polynomials with mixed terms to approximate the true limit state function (LSF) is proposed to analyze the reliability of bypass seepage stability of earth‐rockfill dam. Firstly, the orders of random variable are determined with a univariate fitting. Secondly, nonessential variables are excluded to identify possible mixed terms. Thirdly, orthogonal table is used to arrange additional samples, and stepwise regression is conducted to achieve a specific high‐order response surface polynomial (RSP). Fourthly, Monte Carlo simulation (MCS) is used to calculate the failure probability, and RSP is updated by arranging several additional samplings around the design point. At last, the Bantou complex reinforced earth‐rockfill dam was taken as an example. There are 6 random variables, that is, the upper water level and 5 hydraulic conductivities (HCs). The result shows that a third‐order RSP can ensure good precision, and the failure probability of bypass seepage stability is 3.680 × 10−5 within an acceptable risk range. The HC of concrete cut‐off wall and the HC of rockfill are unimportant random variables. Maximum failure probability at the bank slope has positive correlation with the HC of curtain and the upper water level, negative correlation with the HC of alluvial deposits, and less significance with the HC of filled soil. With the increase of coefficient of variation (Cov) of the HC of curtain, the bypass seepage failure probability increases dramatically. Practical SRSM adopts a nonintrusive form. The reliability analysis and the bypass seepage analysis were conducted separately; therefore, it has a high computational efficiency. Compared with the existing SRSM, the RSP of practical SRSM is simpler and the procedure of the reliability analysis is easier. This paper provides a further evidence for readily application of the high‐order practical SRSM to engineering.
- 1 January 2019
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2019 (1)
Open AccessReliability Analysis for Bypass Seepage Stability of Complex Reinforced Earth‐Rockfill Dam with High‐Order Practical Stochastic Response Surface Method
Practical stochastic response surface method (SRSM) using ordinary high‐order polynomials with mixed terms to approximate the true limit state function (LSF) is proposed to analyze the reliability of bypass seepage stability of earth‐rockfill dam. Firstly, the orders of random variable are determined with a univariate fitting. Secondly, nonessential variables are excluded to identify possible mixed terms. Thirdly, orthogonal table is used to arrange additional samples, and stepwise regression is conducted to achieve a specific high‐order response surface polynomial (RSP). Fourthly, Monte Carlo simulation (MCS) is used to calculate the failure probability, and RSP is updated by arranging several additional samplings around the design point. At last, the Bantou complex reinforced earth‐rockfill dam was taken as an example. There are 6 random variables, that is, the upper water level and 5 hydraulic conductivities (HCs). The result shows that a third‐order RSP can ensure good precision, and the failure probability of bypass seepage stability is 3.680 × 10−5 within an acceptable risk range. The HC of concrete cut‐off wall and the HC of rockfill are unimportant random variables. Maximum failure probability at the bank slope has positive correlation with the HC of curtain and the upper water level, negative correlation with the HC of alluvial deposits, and less significance with the HC of filled soil. With the increase of coefficient of variation (Cov) of the HC of curtain, the bypass seepage failure probability increases dramatically. Practical SRSM adopts a nonintrusive form. The reliability analysis and the bypass seepage analysis were conducted separately; therefore, it has a high computational efficiency. Compared with the existing SRSM, the RSP of practical SRSM is simpler and the procedure of the reliability analysis is easier. This paper provides a further evidence for readily application of the high‐order practical SRSM to engineering.
- Open Access
- 20 May 2015
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2015, 1-11
Strength Reduction Method for Stability Analysis of Local Discontinuous Rock Mass with Iterative Method of Partitioned Finite Element and Interface Boundary Element
SRM (strength reduction method) with iterative method of PFE (partitioned fnite element) and IBE (interface boundary element) is proposed to solve the safety factor of local discontinuous rock mass. Slope system is divided into several continuous bodies and local discontinuous interface boundaries. Each block is treated as a partition of the system and contacted by discontinuous joints. The displacements of blocks are chosen as basic variables and the rigid displacements in the centroid of blocks are chosen as motion variables. The contact forces on interface boundaries and the rigid displacements to the centroid of each body are chosen as mixed variables and solved iteratively using the interface boundary equations. Flexibility matrix is formed through PFE according to the contact states of nodal pairs and spring flexibility is used to reflect the influence of weak structural plane so that nonlinear iteration is only limited to the possible contact region. With cohesion and friction coefficient reduced gradually, the states of all nodal pairs at the open or slip state for the first time are regarded as failure criterion, which can decrease the effect of subjectivity in determining safety factor. Examples are used to verify the validity of the proposed method.
- 20 May 2015
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2015, 1-11
Open AccessStrength Reduction Method for Stability Analysis of Local Discontinuous Rock Mass with Iterative Method of Partitioned Finite Element and Interface Boundary Element
SRM (strength reduction method) with iterative method of PFE (partitioned fnite element) and IBE (interface boundary element) is proposed to solve the safety factor of local discontinuous rock mass. Slope system is divided into several continuous bodies and local discontinuous interface boundaries. Each block is treated as a partition of the system and contacted by discontinuous joints. The displacements of blocks are chosen as basic variables and the rigid displacements in the centroid of blocks are chosen as motion variables. The contact forces on interface boundaries and the rigid displacements to the centroid of each body are chosen as mixed variables and solved iteratively using the interface boundary equations. Flexibility matrix is formed through PFE according to the contact states of nodal pairs and spring flexibility is used to reflect the influence of weak structural plane so that nonlinear iteration is only limited to the possible contact region. With cohesion and friction coefficient reduced gradually, the states of all nodal pairs at the open or slip state for the first time are regarded as failure criterion, which can decrease the effect of subjectivity in determining safety factor. Examples are used to verify the validity of the proposed method.
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 353-356, 1959-1964
ARX Model Identification of Shui-Kou Concrete Gravity Dam Based on Seismic Response Data
Research on the dynamic characteristics of gravity dam was carried out by adopting ARX model using the seismic response data of concrete gravity dam at Shui-Kou hydropower station. The applicability and effectiveness of single-output-multiple-input ARX model were deduced and verified. A corresponding computer program was developed, and performed to identify the modal parameters of the system. The identified natural frequencies and damping ratios were basically same with the results by traditional peak point pick-up method, and also close to the finite element method (FEM) results. It is indicated that the structure natural frequencies and damping ratios are determined by the characteristics of the structure, the dynamic characteristics identified by ARX model are correct, and ARX model can avoid frequency leakiness when smoothing processing and Fourier transform are conducted in solving process of the peak point pick-up method. The modal identification can be applied to other structures.
- 1 August 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 353-356, 1959-1964
ARX Model Identification of Shui-Kou Concrete Gravity Dam Based on Seismic Response Data
Research on the dynamic characteristics of gravity dam was carried out by adopting ARX model using the seismic response data of concrete gravity dam at Shui-Kou hydropower station. The applicability and effectiveness of single-output-multiple-input ARX model were deduced and verified. A corresponding computer program was developed, and performed to identify the modal parameters of the system. The identified natural frequencies and damping ratios were basically same with the results by traditional peak point pick-up method, and also close to the finite element method (FEM) results. It is indicated that the structure natural frequencies and damping ratios are determined by the characteristics of the structure, the dynamic characteristics identified by ARX model are correct, and ARX model can avoid frequency leakiness when smoothing processing and Fourier transform are conducted in solving process of the peak point pick-up method. The modal identification can be applied to other structures.