Sandeep Alanka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sandeep Alanka has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Balla Srinivasa Prasad
GITAM University
4 shared publications Chanamala Ratnam
Department of Mechanical Engineering, College of Engineering (A), Andhra University, India
2 shared publicationsA. V. Sridhar
Mechanical Engineering, GIT, GITAM Deemed To Be University, Visakhapatnam, India
1 shared publication- Dora Siva Prasad
Department of Mechanical Engineering, GITAM (Deemed to be University), Visakhapatnam, India
1 shared publication - G. Veeraiah
Department of Mechanical Engineering, MVGR College of Engineering (A), Vizianagaram, India
1 shared publication Jitendra Gummadi
1 shared publication
Latest Publications
- Open Access
- 20 April 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (5) , 1-12
A review on multi sensor data fusion technique in CNC machining of tailor-made nanocomposites
- 20 April 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (5) , 1-12
Open AccessA review on multi sensor data fusion technique in CNC machining of tailor-made nanocomposites
- Open Access
- 1 May 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 52 (28) , 3973-3985
Characterization of cubic tumbler rod milled dispersed carbon nanotubes–Aluminum composites
In this work, cubic tumbler rod milling was used to disperse X wt% multiwalled carbon nanotubes (X = 0.5, 0.75, 1.0) in an aluminum matrix. Dispersed precursor of aluminum–multiwalled carbon nanotube composite was subsequently consolidated by cold compaction followed by sinter-forged process. Microstructural and mechanical behaviors of as-produced aluminum–multiwalled carbon nanotube composites with different concentration were investigated. Findings revealed that the as-produced Al–0.75 wt% carbon nanotube sinter-forged composite exhibits homogenous distribution and embedded nanotubes confirmed by the scanning electron microscope and the properties were observed to be increased significantly up to addition of 0.75 wt% of carbon nanotubes concentration than the pure aluminum as well as extruded composite and decrease to 1.0 wt% carbon nanotube due to the agglomeration of multiwalled carbon nanotube. However, enhancement of hardness, tensile strength, and Young’s modulus of the nanocomposites, compared with pure aluminum are 48.5, 83.8, and 30%, respectively. The tensile fractography of sinter-forged composite shows carbon nanotubes act like a bridge and barring the crack growth of aluminum matrix, remaining are pullout. Hence, it can be concluded that aluminum carbide phase starting from 0.75 wt% carbon nanotube and a strong interfacial bonding in as-produced aluminum–carbon nanotube composite has been observed which gives effective load transfer between aluminum matrix and carbon nanotubes.
- 1 May 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 52 (28) , 3973-3985
Open AccessCharacterization of cubic tumbler rod milled dispersed carbon nanotubes–Aluminum composites
In this work, cubic tumbler rod milling was used to disperse X wt% multiwalled carbon nanotubes (X = 0.5, 0.75, 1.0) in an aluminum matrix. Dispersed precursor of aluminum–multiwalled carbon nanotube composite was subsequently consolidated by cold compaction followed by sinter-forged process. Microstructural and mechanical behaviors of as-produced aluminum–multiwalled carbon nanotube composites with different concentration were investigated. Findings revealed that the as-produced Al–0.75 wt% carbon nanotube sinter-forged composite exhibits homogenous distribution and embedded nanotubes confirmed by the scanning electron microscope and the properties were observed to be increased significantly up to addition of 0.75 wt% of carbon nanotubes concentration than the pure aluminum as well as extruded composite and decrease to 1.0 wt% carbon nanotube due to the agglomeration of multiwalled carbon nanotube. However, enhancement of hardness, tensile strength, and Young’s modulus of the nanocomposites, compared with pure aluminum are 48.5, 83.8, and 30%, respectively. The tensile fractography of sinter-forged composite shows carbon nanotubes act like a bridge and barring the crack growth of aluminum matrix, remaining are pullout. Hence, it can be concluded that aluminum carbide phase starting from 0.75 wt% carbon nanotube and a strong interfacial bonding in as-produced aluminum–carbon nanotube composite has been observed which gives effective load transfer between aluminum matrix and carbon nanotubes.
- Open Access
- 17 October 2017
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 25 (5) , 983-991
An effective approach to synthesize carbon nanotube-reinforced Al matrix composite precursor
Aluminum-based nanocomposites reinforced with carbon nanotubes have increased scientific attention in today’s life. The dispersion quality was the critical aspect, which decides the homogeneous distribution of CNTs within the Al matrix as starting precursors. In this study, a new attempt has been made to obtain a uniformly dispersed Al-0.75% CNT precursor via combining ultra-sonication, cubic tumbler rod milling, and spray drying. This process was integrated with organic deflocculant (formulator) in specific proportion to transform as a semi-wet-based route. The effect of milling media on the morphology and interface structure of the as-produced composite precursor after all the processing steps was investigated through scanning electron microscope (SEM), high-resolution transmission electron microscope (HRTEM), X-ray diffraction (XRD) analysis, Raman spectroscopy, and Fourier transform infrared spectroscopy. The results reveal that the approach is effective in CNT dispersion in Al precursor, which shields the nanotube structure from damage for longer periods of milling time due to the organic formulator mixture, and also, the CNT retention in the Al precursor with minimum clustering is identified compared to the ball milling process. Carbon traces were confirmed in the as-produced composite precursor by this approach.
- 17 October 2017
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 25 (5) , 983-991
Open AccessAn effective approach to synthesize carbon nanotube-reinforced Al matrix composite precursor
Aluminum-based nanocomposites reinforced with carbon nanotubes have increased scientific attention in today’s life. The dispersion quality was the critical aspect, which decides the homogeneous distribution of CNTs within the Al matrix as starting precursors. In this study, a new attempt has been made to obtain a uniformly dispersed Al-0.75% CNT precursor via combining ultra-sonication, cubic tumbler rod milling, and spray drying. This process was integrated with organic deflocculant (formulator) in specific proportion to transform as a semi-wet-based route. The effect of milling media on the morphology and interface structure of the as-produced composite precursor after all the processing steps was investigated through scanning electron microscope (SEM), high-resolution transmission electron microscope (HRTEM), X-ray diffraction (XRD) analysis, Raman spectroscopy, and Fourier transform infrared spectroscopy. The results reveal that the approach is effective in CNT dispersion in Al precursor, which shields the nanotube structure from damage for longer periods of milling time due to the organic formulator mixture, and also, the CNT retention in the Al precursor with minimum clustering is identified compared to the ball milling process. Carbon traces were confirmed in the as-produced composite precursor by this approach.
- 1 June 2013
- Published by Springer Nature in International Journal of Automation and Computing
- Vol. 10 (3) , 202-209
Condition Monitoring of CNC Machining Using Adaptive Control
- 1 June 2013
- Published by Springer Nature in International Journal of Automation and Computing
- Vol. 10 (3) , 202-209
Condition Monitoring of CNC Machining Using Adaptive Control