Gian Piero Celata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gian Piero Celata has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Sujoy Kumar Saha
Indian Institute of Engineering, Science and Technology, Shibpur
4 shared publications M. Cumo
3 shared publicationsAndrea Mariani
ENEA, Via Anguillarese, 301, 00123 S. M. di Galeria, Rome, Italy
2 shared publications- Giuseppe Zummo
ENEA, Laboratory of Chemical and Thermo-Fluid Dynamic Processes for Energy, Rome, Italy
2 shared publications Luca Saraceno
ENEA, Via Anguillarese, 301, 00123 S. M. di Galeria, Rome, Italy
2 shared publications- Andrea Mariani
Mayo Clinic, Department of Obstetrics and Gynecology, Rochester, MN, USA
1 shared publication
Latest Publications
- 1 October 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 108, 195-208
Evaporating flow experimental tests in small square open channels
- 1 October 2016
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 108, 195-208
Evaporating flow experimental tests in small square open channels
- 1 July 2016
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 75, 115-123
Saturated flow boiling of FC-72 in 1 mm diameter tube
- 1 July 2016
- Published by Elsevier in International Communications in Heat and Mass Transfer
- Vol. 75, 115-123
Saturated flow boiling of FC-72 in 1 mm diameter tube
- 1 January 2016
- Published by Springer Nature
- p. 41-54
Methods of Controlling Instabilities
- 1 January 2016
- Published by Springer Nature
- p. 33-40
Instability Initiation Criterion
- 1 January 2016
- Published by Springer Nature
- p. 9-32
Studies on Two-Phase Flow Instabilities
- 1 September 2014
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 92 (9) , 1616-1628
Experimental results of nanofluids flow effects on metal surfaces
- 1 September 2014
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 92 (9) , 1616-1628
Experimental results of nanofluids flow effects on metal surfaces
- 1 January 2014
- Published by Begell House Inc. Publishers in Journal of Enhanced Heat Transfer
- Vol. 21 (2-3) , 231-258
AN EXPERIMENTAL ANALYSIS OF HEAT TRANSFER CAPABILITY OF NANOFLUIDS IN SINGLE-PHASE TUBULAR FLOWS
In the present paper the results of an experimental investigation on the advantages of using nanofluids for heat transfer operations have been reported. The nanofluid systems varied both in terms of type of particles and their concentration, and of base fluid, for a total of 23 different system configurations. The experimentally derived heat transfer coefficients for these systems, for single-phase forced convection inside tubes, have been compared with those of water or of the corresponding base fluid. The trends identified have been reported as a function of different operating parameters (Re number and fluid average velocity) and the analysis showed that the advantage often claimed for nanofluids actually occurs only under a limited number of hydrodynamic conditions and at the expense of a much higher pumping energy. At the same time, the most commonly adopted correlations for the prediction of the heat transfer coefficient of homogeneous mixtures have been applied to the investigated systems, to check whether it is possible to predict the heat transfer capability of a nanofluid with the ordinary equations by simply introducing the average physical properties of the mixture. It has been found that with the exception of Al2O3 suspensions, in most of the cases the heat transfer coefficient can be actually predicted with a rather good level of accuracy.
- 1 January 2014
- Published by Begell House Inc. Publishers in Journal of Enhanced Heat Transfer
- Vol. 21 (2-3) , 231-258
AN EXPERIMENTAL ANALYSIS OF HEAT TRANSFER CAPABILITY OF NANOFLUIDS IN SINGLE-PHASE TUBULAR FLOWS
In the present paper the results of an experimental investigation on the advantages of using nanofluids for heat transfer operations have been reported. The nanofluid systems varied both in terms of type of particles and their concentration, and of base fluid, for a total of 23 different system configurations. The experimentally derived heat transfer coefficients for these systems, for single-phase forced convection inside tubes, have been compared with those of water or of the corresponding base fluid. The trends identified have been reported as a function of different operating parameters (Re number and fluid average velocity) and the analysis showed that the advantage often claimed for nanofluids actually occurs only under a limited number of hydrodynamic conditions and at the expense of a much higher pumping energy. At the same time, the most commonly adopted correlations for the prediction of the heat transfer coefficient of homogeneous mixtures have been applied to the investigated systems, to check whether it is possible to predict the heat transfer capability of a nanofluid with the ordinary equations by simply introducing the average physical properties of the mixture. It has been found that with the exception of Al2O3 suspensions, in most of the cases the heat transfer coefficient can be actually predicted with a rather good level of accuracy.
- 29 January 2012
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 24 (3) , 203-213
Gravity Influence on Heat Transfer Rate in Flow Boiling
- 29 January 2012
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 24 (3) , 203-213
Gravity Influence on Heat Transfer Rate in Flow Boiling
- Open Access
- 15 April 2011
- Published by Springer Nature in Discover Nano
- Vol. 6 (1) , 344
Advances in modelling of biomimetic fluid flow at different scales
The biomimetic flow at different scales has been discussed at length. The need of looking into the biological surfaces and morphologies and both geometrical and physical similarities to imitate the technological products and processes has been emphasized. The complex fluid flow and heat transfer problems, the fluid-interface and the physics involved at multiscale and macro-, meso-, micro- and nano-scales have been discussed. The flow and heat transfer simulation is done by various CFD solvers including Navier-Stokes and energy equations, lattice Boltzmann method and molecular dynamics method. Combined continuum-molecular dynamics method is also reviewed.
- 15 April 2011
- Published by Springer Nature in Discover Nano
- Vol. 6 (1) , 344
Open AccessAdvances in modelling of biomimetic fluid flow at different scales
The biomimetic flow at different scales has been discussed at length. The need of looking into the biological surfaces and morphologies and both geometrical and physical similarities to imitate the technological products and processes has been emphasized. The complex fluid flow and heat transfer problems, the fluid-interface and the physics involved at multiscale and macro-, meso-, micro- and nano-scales have been discussed. The flow and heat transfer simulation is done by various CFD solvers including Navier-Stokes and energy equations, lattice Boltzmann method and molecular dynamics method. Combined continuum-molecular dynamics method is also reviewed.
- 30 September 2010
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 49 (9) , 1567-1575
Rewetting velocity in quenching at reduced gravity
- 30 September 2010
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 49 (9) , 1567-1575
Rewetting velocity in quenching at reduced gravity