Dong Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dong Wang has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
Caiyun Lou
Tsinghua National Laboratory for Information Science and Technology, and State Key Laboratory of Integrated Optoelectronics, Department of Electronic Engineering, Tsinghua University, Beijing 100084, China
10 shared publications- Han Li
Department of Fundamental Network Technology, China Mobile Research Institute, Beijing 100053, China
10 shared publications - Dechao Zhang
China Mobile Research Institute
9 shared publications - Dawei Ge
China Mobile Research Institute
8 shared publications Li Huo
8 shared publicationsQiang Wang
7 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (19) , 8428-8436
Raman-Free Unified C+L-Band Transmission Enabled by Single-Stage Dual-Pumped Erbium–Bismuth-Doped Fiber Amplification
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (19) , 8428-8436
Raman-Free Unified C+L-Band Transmission Enabled by Single-Stage Dual-Pumped Erbium–Bismuth-Doped Fiber Amplification
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 13 (19) , 44505-44524
LOOR-Based Zero-Shot Target-Region Cotrench Localization in IoT Networks via LLM Expert Knowledge Distillation and CoT Prompting
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 13 (19) , 44505-44524
LOOR-Based Zero-Shot Target-Region Cotrench Localization in IoT Networks via LLM Expert Knowledge Distillation and CoT Prompting
- 11 September 2026
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 18 (10) , 1065-1074
Physics-augmented residual neural network for launch power optimization in ultra-wideband optical transmission systems
Ultra-wideband optical transmission systems suffer from severe inter-channel performance disparities, necessitating effective launch power optimization. However, this objective is often hindered by the complexity or inaccuracy of traditional quality of transmission estimations. To address this limitation, we propose a physics-augmented residual neural network. By delegating primary physics to analytical models and focusing the data-driven task solely on quantifying residual discrepancies, this framework substantially narrows the learning space, enabling high-precision inference with sparse datasets. Using a tandem architecture, the pre-trained forward model is frozen to serve as a differentiable bridge, providing indirect supervision to guide an inverse model for launch power optimization. As a proof-of-concept, a real-time field trial of 120-channel transmission over a 67 km G.652.D fiber is demonstrated across an 18.7 THz S+C+L band. The proposed scheme achieves a quality of transmission estimation accuracy where 97.8% of errors fall within ±0.5dB. In view of the output power limits of S-band optical amplifiers, a flatness of the optical/generalized signal-to-noise ratio of ±0.27dB and ±0.36dB is realized within the individual S band and C+L band, respectively. Compared to purely black-box neural networks, our approach exhibits similar efficacy while reducing the required training samples by 67%.
- 11 September 2026
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 18 (10) , 1065-1074
Physics-augmented residual neural network for launch power optimization in ultra-wideband optical transmission systems
Ultra-wideband optical transmission systems suffer from severe inter-channel performance disparities, necessitating effective launch power optimization. However, this objective is often hindered by the complexity or inaccuracy of traditional quality of transmission estimations. To address this limitation, we propose a physics-augmented residual neural network. By delegating primary physics to analytical models and focusing the data-driven task solely on quantifying residual discrepancies, this framework substantially narrows the learning space, enabling high-precision inference with sparse datasets. Using a tandem architecture, the pre-trained forward model is frozen to serve as a differentiable bridge, providing indirect supervision to guide an inverse model for launch power optimization. As a proof-of-concept, a real-time field trial of 120-channel transmission over a 67 km G.652.D fiber is demonstrated across an 18.7 THz S+C+L band. The proposed scheme achieves a quality of transmission estimation accuracy where 97.8% of errors fall within ±0.5dB. In view of the output power limits of S-band optical amplifiers, a flatness of the optical/generalized signal-to-noise ratio of ±0.27dB and ±0.36dB is realized within the individual S band and C+L band, respectively. Compared to purely black-box neural networks, our approach exhibits similar efficacy while reducing the required training samples by 67%.
- 24 April 2026
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 18 (5) , 492
Field trial of 240 km decentralized training with separation of compute and data based on PFC-assisted hitless 800G OTN
A novel, to our knowledge, PFC-assisted hitless OTN for separation of compute and data is proposed and demonstrated. Based on the new scheme, simulations are conducted and analyzed comprehensively. Simulations indicate that symmetric or asymmetric computing power distribution minimally affects efficiency. With consistent GPUs, larger models experience less impact from remote extension. When training with an appropriate number of GPUs compatible with the model, the degradation rate of training efficiency for models of different sizes remains comparable as the distance increases. Then, the effectiveness of the PFC-assisted hitless OTN is experimentally verified. By hitless protection, pipeline parallelism training efficiency is free from the switchover between primary and backup paths. With the PFC function on, the training efficiency could be improved from 52% to 99.51% over 120 km transmission, compared to the off case. Furthermore, different model sizes, transmission distances, and network convergence ratios are experimentally investigated by the field trial. When extending to 240 km, training efficiency is still up to 99.29%.
- 24 April 2026
- Published by Optica Publishing Group in Journal of Optical Communications and Networking
- Vol. 18 (5) , 492
Field trial of 240 km decentralized training with separation of compute and data based on PFC-assisted hitless 800G OTN
A novel, to our knowledge, PFC-assisted hitless OTN for separation of compute and data is proposed and demonstrated. Based on the new scheme, simulations are conducted and analyzed comprehensively. Simulations indicate that symmetric or asymmetric computing power distribution minimally affects efficiency. With consistent GPUs, larger models experience less impact from remote extension. When training with an appropriate number of GPUs compatible with the model, the degradation rate of training efficiency for models of different sizes remains comparable as the distance increases. Then, the effectiveness of the PFC-assisted hitless OTN is experimentally verified. By hitless protection, pipeline parallelism training efficiency is free from the switchover between primary and backup paths. With the PFC function on, the training efficiency could be improved from 52% to 99.51% over 120 km transmission, compared to the off case. Furthermore, different model sizes, transmission distances, and network convergence ratios are experimentally investigated by the field trial. When extending to 240 km, training efficiency is still up to 99.29%.
- 19 February 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (5) , 1196-1199
High-throughput full-duplex DWDM IM-DD mobile fronthaul based on anti-resonant hollow-core fiber
In this Letter, we experimentally demonstrate a 16.7 Tb/s co-frequency co-time full-duplex 10 km mobile fronthaul on C band by harnessing the ultralow loss, nonlinearity, dispersion, and Rayleigh backscattering of anti-resonant hollow-core fiber. 112 GBaud four-level pulse amplitude modulation signals are adopted with direct detection. Bit error rates of all the channels are below 6.7% hard-decision forward error correction threshold of 3.8 × 10 −3 . Few sensitivity penalties of inter-channel nonlinear interference and backward crosstalk are observed as 0.2 dB and 0.5 dB, respectively. This work shows that anti-resonant hollow-core fiber is a promising medium for implementing a high-capacity 6 G fronthaul architecture.
- 19 February 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (5) , 1196-1199
High-throughput full-duplex DWDM IM-DD mobile fronthaul based on anti-resonant hollow-core fiber
In this Letter, we experimentally demonstrate a 16.7 Tb/s co-frequency co-time full-duplex 10 km mobile fronthaul on C band by harnessing the ultralow loss, nonlinearity, dispersion, and Rayleigh backscattering of anti-resonant hollow-core fiber. 112 GBaud four-level pulse amplitude modulation signals are adopted with direct detection. Bit error rates of all the channels are below 6.7% hard-decision forward error correction threshold of 3.8 × 10 −3 . Few sensitivity penalties of inter-channel nonlinear interference and backward crosstalk are observed as 0.2 dB and 0.5 dB, respectively. This work shows that anti-resonant hollow-core fiber is a promising medium for implementing a high-capacity 6 G fronthaul architecture.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (6) , 2076-2086
Tb/s/λ-Class Co-Frequency Co-Time Full-Duplex WDM Transmission Over 100-km AR-HCF in the S+C+L-band
Optical networks aim to achieve a higher rate per channel and larger capacity per fiber while lowering the cost per bit. Ultra-wide band (UWB) wavelength-division multiplexing (WDM) over single-mode fibers has been widely studied, particularly in the S+C+L-band. However, inter-channel stimulated Raman scattering (ISRS) imposes scalability challenges and limits system capacity. Anti-resonant hollow-core fiber (AR-HCF) emerges as a promising transmission medium for UWB systems due to its ultra-low nonlinearity. The air-guiding mechanism not only brings ultra-low loss but also results in ultra-low Rayleigh backscattering, allowing for direction to be treated as an independent dimension. In this paper, we leverage these advantages to enhance the fiber capacity, demonstrating co-frequency co-time full-duplex (CCFD) S+C+L-band WDM transmission over 100 km AR-HCF to highlight its potential. Since the capacity is primarily constrained by optical/electrical components rather than AR-HCF itself, we employed multiple strategies, including a homemade high-power S-band integrable tunable laser assembly (ITLA) and optical domain equalization (OEQ) to improve the performance of coherent transceivers. It is important to note that gas absorption, as an extrinsic factor, has caused significant impairments in certain channels, which can be partially mitigated by conventional digital signal processing (DSP) techniques. With all these efforts, the capacity of one direction was experimentally measured to be 188.8 Tb/s under a bidirectional transmission configuration, corresponding to an equivalent aggregate bidirectional capacity of 377.6 Tb/s over 100-km AR-HCF. The result underscores the advantages of AR-HCF for ultra-wideband bidirectional transmission.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (6) , 2076-2086
Tb/s/λ-Class Co-Frequency Co-Time Full-Duplex WDM Transmission Over 100-km AR-HCF in the S+C+L-band
Optical networks aim to achieve a higher rate per channel and larger capacity per fiber while lowering the cost per bit. Ultra-wide band (UWB) wavelength-division multiplexing (WDM) over single-mode fibers has been widely studied, particularly in the S+C+L-band. However, inter-channel stimulated Raman scattering (ISRS) imposes scalability challenges and limits system capacity. Anti-resonant hollow-core fiber (AR-HCF) emerges as a promising transmission medium for UWB systems due to its ultra-low nonlinearity. The air-guiding mechanism not only brings ultra-low loss but also results in ultra-low Rayleigh backscattering, allowing for direction to be treated as an independent dimension. In this paper, we leverage these advantages to enhance the fiber capacity, demonstrating co-frequency co-time full-duplex (CCFD) S+C+L-band WDM transmission over 100 km AR-HCF to highlight its potential. Since the capacity is primarily constrained by optical/electrical components rather than AR-HCF itself, we employed multiple strategies, including a homemade high-power S-band integrable tunable laser assembly (ITLA) and optical domain equalization (OEQ) to improve the performance of coherent transceivers. It is important to note that gas absorption, as an extrinsic factor, has caused significant impairments in certain channels, which can be partially mitigated by conventional digital signal processing (DSP) techniques. With all these efforts, the capacity of one direction was experimentally measured to be 188.8 Tb/s under a bidirectional transmission configuration, corresponding to an equivalent aggregate bidirectional capacity of 377.6 Tb/s over 100-km AR-HCF. The result underscores the advantages of AR-HCF for ultra-wideband bidirectional transmission.
- 27 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (3) , 1094-1112
Tb/s-Class Optical Transmission Over AR-HCFs: Field Deployment, Characterization, and Performance
In recent years, anti-resonant hollow-core fibers (AR-HCFs) have made remarkable progress, surpassing the loss limit of conventional silica solid-core fibers, and achieving attenuation below 0.1 dB/km. Due to their ultra-low latency, negligible nonlinearity, and broad transmission bandwidth, AR-HCFs have attracted significant attention from both academia and industry, positioning them as a foundational technology for optical communications over the next half-century. However, large-scale industrial production of AR-HCFs remains underdeveloped, and prior research has been largely confined to laboratory-scale experiments using short fiber segments, failing to fully explore their performance potential or identify deployment-related challenges. To address this gap, we present the field deployments of four structurally distinct AR-HCF cables spanning 10∼42.7 km. Post-deployment measurements demonstrate an average link loss reduction from 0.599 dB/km to 0.113 dB/km, with the lowest recorded span loss reaching 0.065 dB/km, scoring the world’s first fiber cable deployment to break the 0.1 dB/km. Leveraging these deployed links, we conduct real-time coherent transmission experiments at 800 Gb/s to 1.2 Tb/s across S-, C-, and L-bands, validating the feasibility of co-time co-frequency full-duplex (CCFD) transmission in hollow-core fibers and characterizing the impact of gas absorption (e.g., CO2 id="240"> and H2 id="241">O) on system performance. Despite these impairments, we achieve the first field demonstration of real-time terabit-scale coherent transmission over the S+C+L band, delivering a record aggregate capacity of 114.9 Tb/s over 137.36 km using 105 channels.
- 27 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (3) , 1094-1112
Tb/s-Class Optical Transmission Over AR-HCFs: Field Deployment, Characterization, and Performance
In recent years, anti-resonant hollow-core fibers (AR-HCFs) have made remarkable progress, surpassing the loss limit of conventional silica solid-core fibers, and achieving attenuation below 0.1 dB/km. Due to their ultra-low latency, negligible nonlinearity, and broad transmission bandwidth, AR-HCFs have attracted significant attention from both academia and industry, positioning them as a foundational technology for optical communications over the next half-century. However, large-scale industrial production of AR-HCFs remains underdeveloped, and prior research has been largely confined to laboratory-scale experiments using short fiber segments, failing to fully explore their performance potential or identify deployment-related challenges. To address this gap, we present the field deployments of four structurally distinct AR-HCF cables spanning 10∼42.7 km. Post-deployment measurements demonstrate an average link loss reduction from 0.599 dB/km to 0.113 dB/km, with the lowest recorded span loss reaching 0.065 dB/km, scoring the world’s first fiber cable deployment to break the 0.1 dB/km. Leveraging these deployed links, we conduct real-time coherent transmission experiments at 800 Gb/s to 1.2 Tb/s across S-, C-, and L-bands, validating the feasibility of co-time co-frequency full-duplex (CCFD) transmission in hollow-core fibers and characterizing the impact of gas absorption (e.g., CO2 id="240"> and H2 id="241">O) on system performance. Despite these impairments, we achieve the first field demonstration of real-time terabit-scale coherent transmission over the S+C+L band, delivering a record aggregate capacity of 114.9 Tb/s over 137.36 km using 105 channels.
- 19 September 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (19) , 41342-41352
Real-time seamless C + L band DWDM transmission based on unified optics
A real-time DWDM transmission system based on a unified C + L-band architecture is demonstrated. The system incorporates transceiver modules, wavelength-selective switches (WSS), and distributed Raman amplifiers (DRA), all compatible with the full C + L band. A major limitation in previous C + L-band systems is the requirement for separate optical amplifiers for each band, which increases system complexity and cost. This issue is addressed by employing an erbium-bismuth co-doped fiber amplifier (EBDFA), which achieves a 20 dB gain bandwidth of 100 nm. Enabled by these unified components, a total capacity of 62.1 Tb/s is transmitted over 80 km of G.652.D fiber using 70 WDM channels, with per-channel rates up to 1 Tb/s across a seamless 87 nm optical spectrum. The prototype highlights the feasibility of unified C + L-band optics for high-capacity, spectrally efficient, and simplified optical transport networks.
- 19 September 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (19) , 41342-41352
Real-time seamless C + L band DWDM transmission based on unified optics
A real-time DWDM transmission system based on a unified C + L-band architecture is demonstrated. The system incorporates transceiver modules, wavelength-selective switches (WSS), and distributed Raman amplifiers (DRA), all compatible with the full C + L band. A major limitation in previous C + L-band systems is the requirement for separate optical amplifiers for each band, which increases system complexity and cost. This issue is addressed by employing an erbium-bismuth co-doped fiber amplifier (EBDFA), which achieves a 20 dB gain bandwidth of 100 nm. Enabled by these unified components, a total capacity of 62.1 Tb/s is transmitted over 80 km of G.652.D fiber using 70 WDM channels, with per-channel rates up to 1 Tb/s across a seamless 87 nm optical spectrum. The prototype highlights the feasibility of unified C + L-band optics for high-capacity, spectrally efficient, and simplified optical transport networks.
- 23 August 2024
- Published by Optica Publishing Group in Optics Letters
- Vol. 49 (17) , 4887-4890
Experimental study of intramodal XPM reduction by intramodal dispersion in weakly coupled FMF
The understanding of nonlinear propagation effects in low-crosstalk few-mode fiber is crucial for a weakly coupled mode-division multiplexed system. In this Letter, we report the first, to the best of our knowledge, experimental verification of the advantage of intramodal dispersion on mitigating intramodal cross-phase modulation in a weakly coupled few-mode fiber transmission. The experimental system is established over a 70-km multiple-ring-core few-mode fiber accommodating 6 linearly polarized modes, based on which the influences of intramodal cross-phase modulation on transmission performances of each linearly polarized mode are evaluated. Experimental results show that the intramodal cross-phase modulation of degenerate linearly polarized modes with much larger intramodal dispersion values are significantly weaker than those of non-degenerate linearly polarized modes, in which the maximum suppression of intramodal cross-phase modulation noise is up to 9.7 dB. We believe that this work would be beneficial to practical applications of weakly coupled mode-division multiplexing technologies.
- 23 August 2024
- Published by Optica Publishing Group in Optics Letters
- Vol. 49 (17) , 4887-4890
Experimental study of intramodal XPM reduction by intramodal dispersion in weakly coupled FMF
The understanding of nonlinear propagation effects in low-crosstalk few-mode fiber is crucial for a weakly coupled mode-division multiplexed system. In this Letter, we report the first, to the best of our knowledge, experimental verification of the advantage of intramodal dispersion on mitigating intramodal cross-phase modulation in a weakly coupled few-mode fiber transmission. The experimental system is established over a 70-km multiple-ring-core few-mode fiber accommodating 6 linearly polarized modes, based on which the influences of intramodal cross-phase modulation on transmission performances of each linearly polarized mode are evaluated. Experimental results show that the intramodal cross-phase modulation of degenerate linearly polarized modes with much larger intramodal dispersion values are significantly weaker than those of non-degenerate linearly polarized modes, in which the maximum suppression of intramodal cross-phase modulation noise is up to 9.7 dB. We believe that this work would be beneficial to practical applications of weakly coupled mode-division multiplexing technologies.
- 12 January 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (2) , 2554-2560
Robustness of the modified multi-trench fiber design with two gaps
We investigate the robustness of a modified multi-trench fiber (MTF) design with two gaps numerically. The excellent suppression of high-order modes is demonstrated over a wide range of the gap misalignment and the fundamental mode loss is barely affected even with the 5 dB/m scattering loss in gaps at the modified two-gap MTF for the first time. Therefore, the required fabrication accuracy decreases.
- 12 January 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (2) , 2554-2560
Robustness of the modified multi-trench fiber design with two gaps
We investigate the robustness of a modified multi-trench fiber (MTF) design with two gaps numerically. The excellent suppression of high-order modes is demonstrated over a wide range of the gap misalignment and the fundamental mode loss is barely affected even with the 5 dB/m scattering loss in gaps at the modified two-gap MTF for the first time. Therefore, the required fabrication accuracy decreases.