Miroslav Zetek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Miroslav Zetek has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Ivana Zetková
Faculty of Mechanical Engineering University of West Bohemia Univerzitní 8 306 14 Pilsen Czech Republic
12 shared publications - Tomáš Bakša
University of West Bohemia in Pilsen
12 shared publications - Milan Dana
Regional Technological Institute Faculty of Mechanical Engineeering University of West Bohemia Univerzitní 8 306 14 Pilsen Czech Republic
11 shared publications - Pavel Hanzl
Faculty of Mechanical Engineering University of West Bohemia Univerzitní 2732/8 306 14 Pilsen Czech Republic
6 shared publications Tomas Kroupa
4 shared publicationsVaclav Schornik
4 shared publications
Latest Publications
- Open Access
- 16 July 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 213
Fatigue behaviour of L-PBF Inconel 718: influence of surface condition and mean stress with statistical evaluation of S–N curves
- 16 July 2026
- Published by Elsevier in International Journal of Fatigue
- Vol. 213
Open AccessFatigue behaviour of L-PBF Inconel 718: influence of surface condition and mean stress with statistical evaluation of S–N curves
- Open Access
- 23 April 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (2) , 185-198
Influence of the Manufacturing Route on the High-Temperature Oxidation Behavior of IN718 Alloy in Simulated Modern Energy Environments
The use of supercritical water in energy applications is motivated by the aim of increasing the thermal efficiency of power systems. However, structural materials exposed to this environment may undergo corrosive degradation. The objective of ...
- 23 April 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (2) , 185-198
Open AccessInfluence of the Manufacturing Route on the High-Temperature Oxidation Behavior of IN718 Alloy in Simulated Modern Energy Environments
The use of supercritical water in energy applications is motivated by the aim of increasing the thermal efficiency of power systems. However, structural materials exposed to this environment may undergo corrosive degradation. The objective of ...
- 21 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 144 (11) , 7635-7653
Performance evaluation of PVD TaC-coated tools in the drilling of thick CFRP/Al multi-materials
- 21 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 144 (11) , 7635-7653
Performance evaluation of PVD TaC-coated tools in the drilling of thick CFRP/Al multi-materials
- Open Access
- 23 October 2024
- Published by Wiley
Fast fatigue characterization of additively manufactured Inconel 718 using Self-Heating effect
This research investigates the diverse thermal reactions of additively manufactured Inconel 718 samples under cyclic dynamic loading, predominantly influenced by the Self-Heating effect. The study assesses the feasibility of utilizing thermographic techniques to construct an S-N curve for predicting fatigue life with a reduced number of samples compared to conventional constant-amplitude tests. Dedicated Self-Heating tests are performed, systematically elevating the loading amplitude while concurrently tracking the specimen's temperature. The credibility of the proposed solution is juxtaposed with our experimental data, encompassing the influence of four distinct heat treatments on samples from a single additive manufacturing build. This comparison yields valuable insights and leads to noteworthy conclusions.
- 23 October 2024
- Published by Wiley
Open AccessFast fatigue characterization of additively manufactured Inconel 718 using Self-Heating effect
This research investigates the diverse thermal reactions of additively manufactured Inconel 718 samples under cyclic dynamic loading, predominantly influenced by the Self-Heating effect. The study assesses the feasibility of utilizing thermographic techniques to construct an S-N curve for predicting fatigue life with a reduced number of samples compared to conventional constant-amplitude tests. Dedicated Self-Heating tests are performed, systematically elevating the loading amplitude while concurrently tracking the specimen's temperature. The credibility of the proposed solution is juxtaposed with our experimental data, encompassing the influence of four distinct heat treatments on samples from a single additive manufacturing build. This comparison yields valuable insights and leads to noteworthy conclusions.
- Open Access
General Reference and Design S–N Curves Obtained for 1.2709 Tool Steel
At present, due to advanced fatigue calculation models, it is becoming more crucial to find a reliable source for design S–N curves, especially in the case of new 3D-printed materials. Such obtained steel components are becoming very popular and are often used for important parts of dynamically loaded structures. One of the commonly used printing steels is EN 1.2709 tool steel, which has good strength properties and high abrasion resistance, and can be hardened. The research shows, however, that its fatigue strength may differ depending on the printing method, and may be characterized by a wide scatter of the fatigue life. This paper presents selected S–N curves for EN 1.2709 steel after printing with the selective laser melting method. The characteristics are compared, and conclusions are presented regarding the resistance of this material to fatigue loading, especially in the tension–compression state. A combined general mean reference and design fatigue curve is presented, which incorporates our own experimental results as well as those from the literature for the tension–compression loading state. The design curve may be implemented in the finite element method by engineers and scientists in order to calculate the fatigue life.
Open AccessGeneral Reference and Design S–N Curves Obtained for 1.2709 Tool Steel
At present, due to advanced fatigue calculation models, it is becoming more crucial to find a reliable source for design S–N curves, especially in the case of new 3D-printed materials. Such obtained steel components are becoming very popular and are often used for important parts of dynamically loaded structures. One of the commonly used printing steels is EN 1.2709 tool steel, which has good strength properties and high abrasion resistance, and can be hardened. The research shows, however, that its fatigue strength may differ depending on the printing method, and may be characterized by a wide scatter of the fatigue life. This paper presents selected S–N curves for EN 1.2709 steel after printing with the selective laser melting method. The characteristics are compared, and conclusions are presented regarding the resistance of this material to fatigue loading, especially in the tension–compression state. A combined general mean reference and design fatigue curve is presented, which incorporates our own experimental results as well as those from the literature for the tension–compression loading state. The design curve may be implemented in the finite element method by engineers and scientists in order to calculate the fatigue life.
- 1 March 2020
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2020 (1) , 3873-3877
APPLICATION OF LASER SURFACE POLISHING ON ADDITIVE MANUFACTURED PARTS OF INCONEL 718 NICKEL-BASED SUPERALLOY
This article deals with the influence of laser polishing parameters on the final surface quality of nickel-based superalloy Inconel 718 produced by metal additive manufacturing. The aim is to optimize the laser polishing process parameters to reduce the surface roughness of the sample. The investigated parameters of the laser are scanning speed, frequency, focal length, and pulsed and continuous wave regimes are considered. The samples of Inconel 718 are produced by direct metal laser sintering technology. Depending on the printing orientation, the roughness after AM is Ra 5 - 12 mu m. The samples were machined to ensure uniformity of the monitored and tested surface. An IFM - G4 3D optical microscope is used for the surface evaluation. The initial roughness of the samples before applying laser polishing was Ra 1 - 2 mu m. The roughness after laser polishing is significantly reduced to Ra 0.369 mu m.
- 1 March 2020
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2020 (1) , 3873-3877
APPLICATION OF LASER SURFACE POLISHING ON ADDITIVE MANUFACTURED PARTS OF INCONEL 718 NICKEL-BASED SUPERALLOY
This article deals with the influence of laser polishing parameters on the final surface quality of nickel-based superalloy Inconel 718 produced by metal additive manufacturing. The aim is to optimize the laser polishing process parameters to reduce the surface roughness of the sample. The investigated parameters of the laser are scanning speed, frequency, focal length, and pulsed and continuous wave regimes are considered. The samples of Inconel 718 are produced by direct metal laser sintering technology. Depending on the printing orientation, the roughness after AM is Ra 5 - 12 mu m. The samples were machined to ensure uniformity of the monitored and tested surface. An IFM - G4 3D optical microscope is used for the surface evaluation. The initial roughness of the samples before applying laser polishing was Ra 1 - 2 mu m. The roughness after laser polishing is significantly reduced to Ra 0.369 mu m.
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia Structural Integrity
- Vol. 17, 843-849
Mechanical Properties of 18Ni-300 maraging steel manufactured by LPBF
- 1 January 2019
- Published by Elsevier in Procedia Structural Integrity
- Vol. 17, 843-849
Open AccessMechanical Properties of 18Ni-300 maraging steel manufactured by LPBF
- Open Access
- 1 June 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (3) , 389-393
Application of FE Modelling of Machining Using DEFORM™
DEFORM™ is a robust modelling software tool which uses the finite element method (FEM) for modelling technologies in 2D and, naturally, in 3D. One of the processes, the modelling of which DEFORM™ supports, is slab milling.F...
- 1 June 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (3) , 389-393
Open AccessApplication of FE Modelling of Machining Using DEFORM™
DEFORM™ is a robust modelling software tool which uses the finite element method (FEM) for modelling technologies in 2D and, naturally, in 3D. One of the processes, the modelling of which DEFORM™ supports, is slab milling.F...
- 1 February 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (1) , 18-23
Cutting Tool Life when Tapping Nickel Based Super Alloy
This work deals with the issue of tapping Inconel 718 alloy. This material is known for its unique properties of high strength at high temperatures, corrosion resistance, high hardness, work hardening and low thermal conductivity. The machinab...
- 1 February 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (1) , 18-23
Cutting Tool Life when Tapping Nickel Based Super Alloy
This work deals with the issue of tapping Inconel 718 alloy. This material is known for its unique properties of high strength at high temperatures, corrosion resistance, high hardness, work hardening and low thermal conductivity. The machinab...
- Open Access
- 1 February 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (1) , 24-29
Effect of Cutting Edge Geometry on Cutting Forces when Drilling Inconel 718
This work deals with the problematics of cutting forces when drilling holes in Inconel 718. Drills with different geometries of cutting edge were used. The cutting forces and torques were measured during the experiment. The feed cutting force ...
- 1 February 2017
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 17 (1) , 24-29
Open AccessEffect of Cutting Edge Geometry on Cutting Forces when Drilling Inconel 718
This work deals with the problematics of cutting forces when drilling holes in Inconel 718. Drills with different geometries of cutting edge were used. The cutting forces and torques were measured during the experiment. The feed cutting force ...