Damien Violeau
Research Subjects
Damien Violeau has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Michel Benoit
EDF R&D MFEE and IMSIA EDF R&D MFEE EDF R&D LNHE and LHSV EDF R&D LNHE
4 shared publications Agnès Leroy
Laboratoire d’Hydraulique Saint-Venant, Chatou, France
3 shared publications- Antoine Villefer
Laboratoire National d’Hydraulique et Environnement (LNHE)
2 shared publications - Benjamin Dewals
Hydraulics in Environmental and Civil Engineering (HECE), Research Unit Urban & Environmental Engineering (UEE), University of Liège, 4000 Liège, Belgium
2 shared publications - Ismail Rifai
Egis Saint‐Quentin‐en‐Yvelines France
2 shared publications - Kamal El Kadi Abderrezzak
National Laboratory for Hydraulics and Environment (LNHE) EDF R&D Chatou France
2 shared publications
Latest Publications
- 5 March 2026
- Published by Taylor & Francis in Coastal Engineering Journal
- Vol. 68 (2) , 228-244
Wave overtopping of rock-armored breakwaters in bimodal long-crested sea state conditions
1. Storms occurring in coastal areas can lead to both extreme Mean Water Levels (MWL), due to a large storm surge, and extreme sea state conditions. In these conditions, waves can overtop coastal p...
- 5 March 2026
- Published by Taylor & Francis in Coastal Engineering Journal
- Vol. 68 (2) , 228-244
Wave overtopping of rock-armored breakwaters in bimodal long-crested sea state conditions
1. Storms occurring in coastal areas can lead to both extreme Mean Water Levels (MWL), due to a large storm surge, and extreme sea state conditions. In these conditions, waves can overtop coastal p...
- 18 September 2024
- Published by Springer Nature
- p. 473-483
Serre and Boussinesq Models for Favre Waves in Trapezoidal Cross-Sectional Channels
- 18 September 2024
- Published by Springer Nature
- p. 473-483
Serre and Boussinesq Models for Favre Waves in Trapezoidal Cross-Sectional Channels
- 25 February 2023
- Published by Elsevier in Ocean Modelling
- Vol. 183
Spectral wave modeling of bimodal sea states at laboratory and coastal scales
- 25 February 2023
- Published by Elsevier in Ocean Modelling
- Vol. 183
Spectral wave modeling of bimodal sea states at laboratory and coastal scales
- 18 February 2022
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 60 (4) , 606-618
SPH modelling of the water nappe gravity fall over a dam
This work uses the smoothed particle hydrodynamics (SPH) meshless numerical method in order to investigate the behaviour of a water sheet falling under gravity by reproducing the experimental results of a laboratory chute of 9.5 m height. This kind of flow occurs typically over dam ogee-type spillways. The focus is on the trajectory and velocity of the water sheet as well as on the pressure upon impact. Simulations using a combination of adaptive particle refinement, surface tension model and air friction model were tested. The SPH simulations with refinement show good agreement with the experimental pressure results for all comparisons, while using air friction allows correct modelling of the falling velocity distribution.
- 18 February 2022
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 60 (4) , 606-618
SPH modelling of the water nappe gravity fall over a dam
This work uses the smoothed particle hydrodynamics (SPH) meshless numerical method in order to investigate the behaviour of a water sheet falling under gravity by reproducing the experimental results of a laboratory chute of 9.5 m height. This kind of flow occurs typically over dam ogee-type spillways. The focus is on the trajectory and velocity of the water sheet as well as on the pressure upon impact. Simulations using a combination of adaptive particle refinement, surface tension model and air friction model were tested. The SPH simulations with refinement show good agreement with the experimental pressure results for all comparisons, while using air friction allows correct modelling of the falling velocity distribution.
- 25 March 2021
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (6) , 888-902
Single-phase SPH modelling of plunge pool dynamic pressures at a near-prototype scale
The turbulent plunging jet of a nearly incompressible fluid into a stagnant fluid is of great importance in many practical applications, especially for the engineering of hydropower. As an example, the dynamic load exerted by the impact of turbulent high-velocity jets into a pool must be estimated to evaluate the potential destabilization of a rock bed or dam’s structure. Modelling plunging jets in the laboratory presents a challenge due to the complex two-phase environment, which requires models to be built at near-prototype scales. This paper deals with the application of a three-dimensional weakly compressible smoothed particle hydrodynamics (SPH) model to study a circular jet impinging into a water flat pool, at a near-prototype scale. To identify the level of reliability of the computed parameters, validation of the pool bottom pressures is carried out by comparison with existing experimental data. The self-similarity of the jet’s centreline velocity is correctly reproduced and the computed maximum dynamic pressures near the stagnation point are reasonably accurate. The differences observed are mainly attributed to the non-consideration of the air phase.
- 25 March 2021
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (6) , 888-902
Single-phase SPH modelling of plunge pool dynamic pressures at a near-prototype scale
The turbulent plunging jet of a nearly incompressible fluid into a stagnant fluid is of great importance in many practical applications, especially for the engineering of hydropower. As an example, the dynamic load exerted by the impact of turbulent high-velocity jets into a pool must be estimated to evaluate the potential destabilization of a rock bed or dam’s structure. Modelling plunging jets in the laboratory presents a challenge due to the complex two-phase environment, which requires models to be built at near-prototype scales. This paper deals with the application of a three-dimensional weakly compressible smoothed particle hydrodynamics (SPH) model to study a circular jet impinging into a water flat pool, at a near-prototype scale. To identify the level of reliability of the computed parameters, validation of the pool bottom pressures is carried out by comparison with existing experimental data. The self-similarity of the jet’s centreline velocity is correctly reproduced and the computed maximum dynamic pressures near the stagnation point are reasonably accurate. The differences observed are mainly attributed to the non-consideration of the air phase.
- 11 January 2021
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (6) , 863-887
SPH simulation of the 2007 Chehalis Lake landslide and subsequent tsunami
A multi-phase smoothed particle hydrodynamics (SPH) formulation in combination with a granular rheological model is applied to simulate the 2007 Chehalis Lake landslide and the subsequent tsunami. The model is implemented within the open-source 3D code GPUSPH. The lake geometry is built using the British Colombia Hydro (BCH) topography and bathymetry surveys, and the landslide initial geometry is reconstructed from pre- and post-failure geological profiles under the assumption of constant thickness across the entire width. The water and the landslide are treated as immiscible continua, discretized in two distinct sets of SPH particles with different mass and behaviour laws. The landslide material is modelled as a continuum whose shear stresses obey a friction law that takes its granular nature into consideration. A sensitive analysis for various physical parameters is carried out, and numerical results are checked by comparing run-up heights to BCH's surveys.
- 11 January 2021
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (6) , 863-887
SPH simulation of the 2007 Chehalis Lake landslide and subsequent tsunami
A multi-phase smoothed particle hydrodynamics (SPH) formulation in combination with a granular rheological model is applied to simulate the 2007 Chehalis Lake landslide and the subsequent tsunami. The model is implemented within the open-source 3D code GPUSPH. The lake geometry is built using the British Colombia Hydro (BCH) topography and bathymetry surveys, and the landslide initial geometry is reconstructed from pre- and post-failure geological profiles under the assumption of constant thickness across the entire width. The water and the landslide are treated as immiscible continua, discretized in two distinct sets of SPH particles with different mass and behaviour laws. The landslide material is modelled as a continuum whose shear stresses obey a friction law that takes its granular nature into consideration. A sensitive analysis for various physical parameters is carried out, and numerical results are checked by comparing run-up heights to BCH's surveys.
- Open Access
- 28 September 2020
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 56 (10)
Continuous Monitoring of Fluvial Dike Breaching by a Laser Profilometry Technique
A nonintrusive, high‐resolution laser profilometry technique (LPT) has been developed for continuous monitoring of the three‐dimensional (3‐D) evolving breach in laboratory models of noncohesive fluvial dikes. This simple and low‐cost setup consists of a commercial digital video camera and a sweeping red diode 30 mW laser projecting a sheet over the dike. The 2‐D image coordinates of each deformed laser profile incident on the dike are transformed into 3‐D object coordinates using the direct linear transformation (DLT) algorithm. All 3‐D object coordinates computed over a laser sweeping cycle are merged to generate a cloud of points describing the instantaneous surface. The DLT‐based image processing algorithm uses control points and reference axes, so that no prior knowledge is needed on the position, orientation, and intrinsic characteristics of the camera, nor on the laser position. Because the dike is partially submerged, ad hoc refraction correction has been developed. Algorithms and instructions for the implementation of the LPT are provided. Reconstructions of a dike geometry with the LPT and with a commercial laser scanner are compared in dry conditions. Using rigid dike geometries, the repeatability of the measurements, the refraction correction, and the dike reconstruction have been evaluated for submerged conditions. Two laboratory studies of evolving fluvial dike breaching due to flow overtopping have been conducted to demonstrate the LPT capabilities and accuracy. The LPT has advantages in terms of flexibility and spatiotemporal resolution, but high turbidity and water surface waves may lead to inaccurate geometry reconstructions.
- 28 September 2020
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 56 (10)
Open AccessContinuous Monitoring of Fluvial Dike Breaching by a Laser Profilometry Technique
A nonintrusive, high‐resolution laser profilometry technique (LPT) has been developed for continuous monitoring of the three‐dimensional (3‐D) evolving breach in laboratory models of noncohesive fluvial dikes. This simple and low‐cost setup consists of a commercial digital video camera and a sweeping red diode 30 mW laser projecting a sheet over the dike. The 2‐D image coordinates of each deformed laser profile incident on the dike are transformed into 3‐D object coordinates using the direct linear transformation (DLT) algorithm. All 3‐D object coordinates computed over a laser sweeping cycle are merged to generate a cloud of points describing the instantaneous surface. The DLT‐based image processing algorithm uses control points and reference axes, so that no prior knowledge is needed on the position, orientation, and intrinsic characteristics of the camera, nor on the laser position. Because the dike is partially submerged, ad hoc refraction correction has been developed. Algorithms and instructions for the implementation of the LPT are provided. Reconstructions of a dike geometry with the LPT and with a commercial laser scanner are compared in dry conditions. Using rigid dike geometries, the repeatability of the measurements, the refraction correction, and the dike reconstruction have been evaluated for submerged conditions. Two laboratory studies of evolving fluvial dike breaching due to flow overtopping have been conducted to demonstrate the LPT capabilities and accuracy. The LPT has advantages in terms of flexibility and spatiotemporal resolution, but high turbidity and water surface waves may lead to inaccurate geometry reconstructions.
- 25 September 2020
- Published by Springer Nature in Natural Hazards
- Vol. 105 (1) , 735-753
Cosmogenic tsunamic risk assessment: a first application to the European Atlantic coasts
- 25 September 2020
- Published by Springer Nature in Natural Hazards
- Vol. 105 (1) , 735-753
Cosmogenic tsunamic risk assessment: a first application to the European Atlantic coasts
- 17 February 2020
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (1) , 75-87
Apparent cohesion effects on overtopping-induced fluvial dike breaching
Flow overtopping can lead to the initiation of breaching and failure of fluvial dikes, causing severe inundations and damage in the protected areas. For flood risk management and prevention, the accurate estimate of flow discharge across the fluvial dike breach is paramount, requiring precise understanding of the breach expansion. Laboratory experiments were conducted to analyse the effects of fine sand, inducing apparent cohesion in the dike material, on breach development and outflow. Tests were conducted under controlled inflow discharge and dike material composed of either homogeneous non-cohesive coarse sand or heterogeneous fine sand/coarse sand mixtures. Based on the non-intrusive laser profilometry technique, high temporal and spatial resolution of the three-dimensional breach geometry evolution was measured, indicating a small effect of the fine material on the overall breach dynamics. A detailed analysis revealed, however, that fine sand induces less frequent slope collapses but larger sliding/failing lumps compared to homogenous non-cohesive coarse sand.
- 17 February 2020
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 59 (1) , 75-87
Apparent cohesion effects on overtopping-induced fluvial dike breaching
Flow overtopping can lead to the initiation of breaching and failure of fluvial dikes, causing severe inundations and damage in the protected areas. For flood risk management and prevention, the accurate estimate of flow discharge across the fluvial dike breach is paramount, requiring precise understanding of the breach expansion. Laboratory experiments were conducted to analyse the effects of fine sand, inducing apparent cohesion in the dike material, on breach development and outflow. Tests were conducted under controlled inflow discharge and dike material composed of either homogeneous non-cohesive coarse sand or heterogeneous fine sand/coarse sand mixtures. Based on the non-intrusive laser profilometry technique, high temporal and spatial resolution of the three-dimensional breach geometry evolution was measured, indicating a small effect of the fine material on the overall breach dynamics. A detailed analysis revealed, however, that fine sand induces less frequent slope collapses but larger sliding/failing lumps compared to homogenous non-cohesive coarse sand.