Jesus Urresti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jesus Urresti has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Jose Rebollo
CNM-IMB CSIC
18 shared publications - Salvador Hidalgo
Institute of Microelectronics of Barcelona (IMB-CNM-CSIC), Cerdanyola del Vallès
15 shared publications D. Flores
10 shared publicationsJ. Roig
Com.pub2web.rdf.cci.facet.ContentItem[id=http://iet.metastore.ingenta.com/content/journals/10.1049/ip-cds_20050052-af1,webId=/content/journals/10.1049/ip-cds_20050052-af1,properties={vcard_country-name=Spain, vcard_locality=Bellaterra, vcard_organisation-name=Centro Nacional de Microelectrónica (CNM-CSIC), vcard_organisation-unit=Power Devices and Systems Group}
9 shared publications- Alberto Castellazzi
Kyoto University of Advanced Science
8 shared publications - Nicholas G. Wright
School of Engineering, Newcastle University, Newcastle upon Tyne, U.K.
8 shared publications
Latest Publications
- 6 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (4) , 1710-1716
Design and Analysis of High Mobility Enhancement-Mode 4H-SiC MOSFETs Using a Thin-SiO2/Al2O3Gate-Stack
High-performance 4H-SiC MOSFETs have been fabricated, having a peak effective mobility of 265 cm 2 /$\text{V}\,\cdot $ s, and a peak field effect mobility of 154 cm 2 /V s, in 2-$\mu $ m gate length MOSFETs. The gate-stack was designed to minimize interface states and comprised a 0.7-nm thermally grown SiO 2 on 4H-SiC, followed by Al 2 O 3 and a metal gate contact. In this way, carbon remaining following SiC oxidation is significantly reduced. A density of interface traps in the range of$6 \times 10^{11} - 5 \times 10^{10}$ cm −2 eV −1 is also obtained. Temperature-dependent electrical data reveal that the high mobility results from conduction being phonon-limited, rather than Coulomb-limited. Furthermore, universal mobility in these 4H-SiC MOSFETs is shown to be up to 50% of that observed in the Si devices. Expressions for electric field-dependent contributions to mobility are presented. A steep subthreshold slope of 127 mV/decade indicates low electrical defect density. A temperature coefficient of −4.6 mV/K in threshold voltage is similar to that in the Si MOSFETs.- 6 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (4) , 1710-1716
Design and Analysis of High Mobility Enhancement-Mode 4H-SiC MOSFETs Using a Thin-SiO2/Al2O3Gate-Stack
High-performance 4H-SiC MOSFETs have been fabricated, having a peak effective mobility of 265 cm 2 /$\text{V}\,\cdot $ s, and a peak field effect mobility of 154 cm 2 /V s, in 2-$\mu $ m gate length MOSFETs. The gate-stack was designed to minimize interface states and comprised a 0.7-nm thermally grown SiO 2 on 4H-SiC, followed by Al 2 O 3 and a metal gate contact. In this way, carbon remaining following SiC oxidation is significantly reduced. A density of interface traps in the range of$6 \times 10^{11} - 5 \times 10^{10}$ cm −2 eV −1 is also obtained. Temperature-dependent electrical data reveal that the high mobility results from conduction being phonon-limited, rather than Coulomb-limited. Furthermore, universal mobility in these 4H-SiC MOSFETs is shown to be up to 50% of that observed in the Si devices. Expressions for electric field-dependent contributions to mobility are presented. A steep subthreshold slope of 127 mV/decade indicates low electrical defect density. A temperature coefficient of −4.6 mV/K in threshold voltage is similar to that in the Si MOSFETs.- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 494-497
High-Mobility SiC MOSFETs Using a Thin-SiO2/Al2O3 Gate Stack
We report the development of a low-temperature (600 °C) gate oxidation approach to minimize the density of interface traps (DIT) at the SiC/SiO2 interface, ultimately leading to a significantly higher channel mobility in SiC MOSFETs of 81 cm2·V-1·s-1, >11x higher than devices fabricated alongside but with a conventional 1150 °C gate oxide. We further report on the comparison made between the DIT and channel mobilities of MOS capacitors and n-MOSFETs fabricated using the low-and high-temperature gate oxidation.
- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 494-497
High-Mobility SiC MOSFETs Using a Thin-SiO2/Al2O3 Gate Stack
We report the development of a low-temperature (600 °C) gate oxidation approach to minimize the density of interface traps (DIT) at the SiC/SiO2 interface, ultimately leading to a significantly higher channel mobility in SiC MOSFETs of 81 cm2·V-1·s-1, >11x higher than devices fabricated alongside but with a conventional 1150 °C gate oxide. We further report on the comparison made between the DIT and channel mobilities of MOS capacitors and n-MOSFETs fabricated using the low-and high-temperature gate oxidation.
- 19 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (4) , 564-567
Increased Mobility in Enhancement Mode 4H-SiC MOSFET Using a Thin SiO2/ Al2O3Gate Stack
A field effect mobility of 125 cm $^{\textsf {2}}/\text{V}\cdot \text{s}$ and a subthreshold slope of 130 mV/dec were obtained in enhancement mode 4H-SiC MOSFETs with a channel length of $2~\mu \text{m}$ . The fabricated devices utilized a gate stack comprising a 0.7 nm thin thermal SiO 2 , thereby reducing defects following oxidation, and a 40 nm thick Al 2 O 3 formed by atomic layer deposition. A high mobility was maintained over a wide gate voltage range and resulted in increases of up to $120\times $ in drain current for the same gate overdrive voltage compared to MOSFETs having a thicker thermal SiO 2 gate stack with the same effective oxide thickness fabricated alongside. Nitridation is not included in either MOSFET process.
- 19 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 39 (4) , 564-567
Increased Mobility in Enhancement Mode 4H-SiC MOSFET Using a Thin SiO2/ Al2O3Gate Stack
A field effect mobility of 125 cm $^{\textsf {2}}/\text{V}\cdot \text{s}$ and a subthreshold slope of 130 mV/dec were obtained in enhancement mode 4H-SiC MOSFETs with a channel length of $2~\mu \text{m}$ . The fabricated devices utilized a gate stack comprising a 0.7 nm thin thermal SiO 2 , thereby reducing defects following oxidation, and a 40 nm thick Al 2 O 3 formed by atomic layer deposition. A high mobility was maintained over a wide gate voltage range and resulted in increases of up to $120\times $ in drain current for the same gate overdrive voltage compared to MOSFETs having a thicker thermal SiO 2 gate stack with the same effective oxide thickness fabricated alongside. Nitridation is not included in either MOSFET process.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 327-330
Characterisation of 4H-SiC MOS Capacitor with a Protective Coating for Harsh Environments Applications
Oxygen free Ohmic contacts are essential for the realisation of high performance devices. Ohmic contacts in SiC often require annealing under vacuum at over 1000 °C, whilst high-κ dielectrics are usually annealed in O2 rich ambient at temperatures of 800 °C or less, affecting the electrical and surface characteristics. Therefore, protection of the Ohmic contacts during the annealing of a high-κ dielectric layer is a key enabling step in the realisation of high performance MOS structures. In order to prevent damage during the high-k formation the use of silicon nitride as a passivation layer, capable of protecting the contacts during annealing, has been investigated. In this work we have investigated and compared silicon nitride protected high-κ dielectric SiC based MOS capacitors with the unprotected SiC MOS devices in terms of electrical and optical characteristics.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 327-330
Characterisation of 4H-SiC MOS Capacitor with a Protective Coating for Harsh Environments Applications
Oxygen free Ohmic contacts are essential for the realisation of high performance devices. Ohmic contacts in SiC often require annealing under vacuum at over 1000 °C, whilst high-κ dielectrics are usually annealed in O2 rich ambient at temperatures of 800 °C or less, affecting the electrical and surface characteristics. Therefore, protection of the Ohmic contacts during the annealing of a high-κ dielectric layer is a key enabling step in the realisation of high performance MOS structures. In order to prevent damage during the high-k formation the use of silicon nitride as a passivation layer, capable of protecting the contacts during annealing, has been investigated. In this work we have investigated and compared silicon nitride protected high-κ dielectric SiC based MOS capacitors with the unprotected SiC MOS devices in terms of electrical and optical characteristics.
- Open Access
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 391-394
Influence of gate bias on the avalanche ruggedness of SiC power MOSFETs
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 391-394
Open AccessInfluence of gate bias on the avalanche ruggedness of SiC power MOSFETs
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2A-3.1-2A-3.8
Transient out-of-SOA robustness of SiC power MOSFETs
Beyond their main function of high-frequency switches in modulated power converters, solid-state power devices are required in many application domains to also ensure robustness against a number of overload operational conditions. This paper considers the specific case of 1200 V SiC power MOSFETs and analyses their performance under three main transient regimes at the edge of and out of their Safe Operating Area: unclamped inductive switching led avalanche breakdown; short-circuit; operation as current limiting and regulating devices. The results presented highlight both inherent major strengths of SiC over Si and areas for improvement by tailored device design. The paper aims to contribute useful indications for technology development in future device generations to better match widespread and varied application requirements.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2A-3.1-2A-3.8
Transient out-of-SOA robustness of SiC power MOSFETs
Beyond their main function of high-frequency switches in modulated power converters, solid-state power devices are required in many application domains to also ensure robustness against a number of overload operational conditions. This paper considers the specific case of 1200 V SiC power MOSFETs and analyses their performance under three main transient regimes at the edge of and out of their Safe Operating Area: unclamped inductive switching led avalanche breakdown; short-circuit; operation as current limiting and regulating devices. The results presented highlight both inherent major strengths of SiC over Si and areas for improvement by tailored device design. The paper aims to contribute useful indications for technology development in future device generations to better match widespread and varied application requirements.
- Open Access
A Comprehensive Study on the Avalanche Breakdown Robustness of Silicon Carbide Power MOSFETs
This paper presents an in-depth investigation into the avalanche breakdown robustness of commercial state-of-the-art silicon carbide (SiC) power MOSFETs comprising of functional as well as structural characterization and the corresponding underlying physical mechanisms responsible for device failure. One aspect of robustness for power MOSFETs is determined by its ability to withstand energy during avalanche breakdown. Avalanche energy (EAV) is an important figure of merit for all applications requiring load dumping and/or to benefit from snubber-less converter design. 2D TCAD electro-thermal simulations were performed to get important insight into the failure mechanism of SiC power MOSFETs during avalanche breakdown.
Open AccessA Comprehensive Study on the Avalanche Breakdown Robustness of Silicon Carbide Power MOSFETs
This paper presents an in-depth investigation into the avalanche breakdown robustness of commercial state-of-the-art silicon carbide (SiC) power MOSFETs comprising of functional as well as structural characterization and the corresponding underlying physical mechanisms responsible for device failure. One aspect of robustness for power MOSFETs is determined by its ability to withstand energy during avalanche breakdown. Avalanche energy (EAV) is an important figure of merit for all applications requiring load dumping and/or to benefit from snubber-less converter design. 2D TCAD electro-thermal simulations were performed to get important insight into the failure mechanism of SiC power MOSFETs during avalanche breakdown.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 118-122
UIS failure mechanism of SiC power MOSFETs
This paper investigates the failure mechanism of SiC power MOSFETs during avalanche breakdown under unclamped inductive switching (UIS) test regime. Switches deployed within motor drive applications could experience undesired avalanche breakdown events. Therefore, avalanche ruggedness is an important feature of power devices enabling snubber-less converter design and is also a desired feature in certain applications such as automotive. It is essential to thoroughly characterize SiC power MOSFETs for better understanding of their robustness and more importantly of their corresponding underling physical mechanisms responsible for failure in order to inform device design and technology evolution. Experimental results during UIS at failure and 2D TCAD simulation results are presented in this study.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 118-122
UIS failure mechanism of SiC power MOSFETs
This paper investigates the failure mechanism of SiC power MOSFETs during avalanche breakdown under unclamped inductive switching (UIS) test regime. Switches deployed within motor drive applications could experience undesired avalanche breakdown events. Therefore, avalanche ruggedness is an important feature of power devices enabling snubber-less converter design and is also a desired feature in certain applications such as automotive. It is essential to thoroughly characterize SiC power MOSFETs for better understanding of their robustness and more importantly of their corresponding underling physical mechanisms responsible for failure in order to inform device design and technology evolution. Experimental results during UIS at failure and 2D TCAD simulation results are presented in this study.
- 1 September 2014
- Published by Elsevier in Microelectronics Reliability
- Vol. 54 (9-10) , 1906-1910
Overload robust IGBT design for SSCB application
- 1 September 2014
- Published by Elsevier in Microelectronics Reliability
- Vol. 54 (9-10) , 1906-1910
Overload robust IGBT design for SSCB application
- Open Access
- 1 May 2014
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 8 (3) , 182-187
3.3 kV PT‐IGBT with voltage‐sensor monolithically integrated
An intelligent insulated gate bipolar transistor (IGBT) suitable to be used in remote‐controlled on‐load tap changers and traction applications is analysed in this study. An anode voltage sensor monolithically integrated in the active area of a 3.3 kV–50 A PT‐IGBT is introduced to enhance the robustness of the IGBT against short‐circuit events. The operation mode of the anode voltage sensor is described and TCAD simulations are performed to describe the static and dynamic performance together with the interaction between the sensor and the IGBT core cells. The study of the anode voltage performance under inductive turn‐off conditions is also included, comparing the behaviour of IGBTs with and without anode voltage sensor.
- 1 May 2014
- Published by Institution of Engineering and Technology (IET) in IET Circuits, Devices & Systems
- Vol. 8 (3) , 182-187
Open Access3.3 kV PT‐IGBT with voltage‐sensor monolithically integrated
An intelligent insulated gate bipolar transistor (IGBT) suitable to be used in remote‐controlled on‐load tap changers and traction applications is analysed in this study. An anode voltage sensor monolithically integrated in the active area of a 3.3 kV–50 A PT‐IGBT is introduced to enhance the robustness of the IGBT against short‐circuit events. The operation mode of the anode voltage sensor is described and TCAD simulations are performed to describe the static and dynamic performance together with the interaction between the sensor and the IGBT core cells. The study of the anode voltage performance under inductive turn‐off conditions is also included, comparing the behaviour of IGBTs with and without anode voltage sensor.