JAJohn D. Albrecht

John D. Albrecht

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


John D. Albrecht has a total of 112 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Miniaturized Millimeter-Wave Multilayer Filter Design Using Additive Manufacturing

    by Nicholas Sturim, Premjeet Chahal, Matthew Hodek, John D. Albrecht, John Papapolymerou

    This paper presents an innovative, fully additive manufactured approach to millimeter-wave multilayer circuits. An aerosol jet printer is used to fabricate a multilayer stepped-impedance low-pass filter. By leveraging the second layer for miniaturization, we achieve a more compact design. By precisely controlling conductor separation and utilizing 3D printing technology, we were able to optimize the width of the high and low-impedance segments for optimal filter performance. Two filter types were successfully fabricated: a low-pass microstrip filter and a low-pass stripline filter, both with a cutoff frequency near 29 GHz and exhibiting acceptable stopband attenuation. The stripline configuration allows for a 36 % decrease in the stripline waveguide conductor area while achieving a great passband insertion loss of just 0.62 dB, enabled by aerosol jet printing. The line loss of both designs was characterized using a microstrip through line and a stripline through line. Both designs demonstrated low overall loss, with the microstrip line exhibiting a loss of 0.26 dB/mm and the stripline having a loss of 0.37 dB/mm at 29 GHz. This work demonstrates a multilayer integration solution and offers an advantage in reducing the size of RF circuits such as filter banks for next-generation integrated RF front-ends.

  • Low-Power Characterization and Integration of Carbon Black Resistive Ink for Aerosol Jet-Printed RF Components

    by Koltin Grammer, John Albrecht, Prem Chahal, Matt Hodek, John Papapolymerou

    Aerosol jet printing (AJP) is gaining attention in additive manufacturing research, especially in the discipline of microwave engineering. Currently, no reliable AJP method exists to fabricate resistors that are both electrically small and with a resistance compatible with waveguide impedances for use in microwave components. In this work, the commercially available Metalon JR-038 is characterized and used to fabricate a resistor that is 100 $\mu$ m long by 250 $\mu$ m wide for the first time to the best of our knowledge. This resistor was then used to fabricate a Ka-band Wilkinson power divider using only the AJP process.

  • Aerosol-Jet Printed Transferable Millimeter-Wave Circuits

    by Wesley Spain, John Papapolymerou, Prem Chahal, Matthew Hodek, John D. Albrecht

    Printed millimeter wave (mmW) electronics have been of high interest in the field of communications for some time now due to the potential ability to fabricate mmW systems that utilize 3-Dimension Heterogeneous Integration (3DHI) to improve performance beyond traditional systems. In this paper, a method for fabricating transferable mmW structures via aerosol-jet printing (AJP) is presented. A PDMS stamp assisted liftoff procedure is developed to separate the printed part from a rigid printing support surface and apply it to an adhesive target surface. Several microstrip (MS) line structures are demonstrated to characterize the effect of stamp transfer on the RF performance of the printed circuits. The effects of printed vias on RF probe pads and shifts in the resonant frequencies of a Beatty standard line after transfer are considered and characterized using S-parameter measurements.


  • Chemical Mechanical Polishing of Single-Crystalline Diamond Epitaxial Layers for Electronics Applications

    by Aaron Hardy, Matthias Muehle, Cristian Herrera-Rodriguez, Michael Becker, Edward Drown, Nina Baule, Mark Tompkins, Timothy Grotjohn, John D. Albrecht

    For single crystal diamond (SCD) to gain practical use in technical applications including solid state electronics, thin (<1 μm), doped epitaxial SCD layers with very low (<1 nm) surface roughness are required. Conventional SCD chemical mechanical polishing (CMP) processes are insufficient to meet the requirements of such applications because the material removal rate (MRR) is often characterized inappropriately, and the material removal uniformity is seldom considered. In this study, chemical vapor deposition (CVD) growth of two lightly boron doped (p-) epilayers was performed on 3misoriented (100) high pressure high temperature substrates of 4.5 x 4.5 mm2 area. A subsequent 8-hour oxidative CMP process utilizing potassium permanganate and a novel self-leveling holder design decreased the average surface roughness from 3.83 nm and 1.57 nm to 0.20 nm and 0.16 nm for the two samples, respectively. MRRs were determined by evaluating five circular wear monitor structures in each sample by atomic force microscopy before and after the CMP process. The average MRRs were found to be 38.6 nm/hr and 37.3 nm/hr for the two samples. The purpose of this study is to demonstrate a CMP process suitable for polishing thin SCD epilayers to meet the needs of solid-state electronics applications.


  • Fully Aerosol Jet-Printed Passive Components for 140–220-GHz Operation

    by Xenofon Konstantinou, Xing Lan, Khanh Nguyen, Alfonso Escorcia, Rajinder Sandhu, Jesse Tice, Wesley Spain, John D. Albrecht, John Papapolymerou

    This letter focuses on the unique capabilities that aerosol jet printing (AJP) provides for manufacturing electronics at near-THz frequencies. For the first time, we demonstrate fully aerosol jet-printed passive components above the $W$ -band. Dielectric substrates and conductors are printed on metal carriers via AJP. These components include microstrip (MS) transmission lines (TLs) and radial stubs, and utilize vialess grounded coplanar waveguide (GCPW)-to-MS TL launches. Two separate sets of components and calibration structures are realized, for two different dielectric thicknesses. For the TLs, measured from 140 to 220 GHz, the average loss varies from 0.86 to 2.6 dB/mm. The radial stub return loss, measured from 200 to 220 GHz, is closely aligned with simulations.


  • Experimentally Validated Gate-Lag Simulations of AlGaN/GaN HEMTs Using Fermi Kinetics Transport

    by Nicholas C. Miller, Matt Grupen, Ahmad E. Islam, John D. Albrecht, Dave Frey, Richard Young, Miles Lindquist, Andrew J. Green, Dennis E. Walker, Kelson D. Chabak

    This article presents for the first time a direct connection between gate lag observed in drain current transient measurements of gallium nitride (GaN) high-electron-mobility transistors (HEMTs) and traps located in the barrier of the transistor epitaxy. Semiclassical numerical simulations are presented using the Air Force Research Laboratory’s (AFRL’s) Fermi kinetics transport (FKT) solver and are validated with drain current transient measurements. Capacitance–voltage ( ${C} - {V}$ ) and conductance–voltage ( ${G} - {V}$ ) measurements are also presented to provide further insights into the trap location used in the FKT simulations. These simulations indicate that equivalent defects located specifically at the AlGaN barrier/GaN cap interface of an AFRL GaN HEMT with a density of $7.5\times 10^{{12}}$ cm−2 and positioned 1.464 eV below the GaN cap conduction band edge were the salient traps linked to the gate-lag phenomenon. The study highlights the importance of experimentally benchmarked device simulation for trapping analysis in GaN HEMTs and may provide significant insights into device engineers for mitigating trapping effects in state-of-the-art GaN technologies.


  • A comparison of a commercial hydrodynamics TCAD solver and Fermi kinetics transport convergence for GaN HEMTs

    by Ashwin Tunga, Kexin Li, Ethan White, Nicholas C. Miller, Matt Grupen, John D. Albrecht, Shaloo Rakheja

    Various simulations of a GaN HEMT are used to study the behaviors of two different energy-transport models: the Fermi kinetics transport model and a hydrodynamics transport model as it is implemented in the device simulator Sentaurus from Synopsys. The electron transport and heat flow equations of the respective solvers are described in detail. The differences in the description of electron flux and the discretization methods are highlighted. Next, the transport models are applied to the same simulated device structure using identical meshes, boundary conditions, and material parameters. Static simulations show the numerical convergence of Fermi kinetics to be consistently quadratic or faster, whereas the hydrodynamic model is often sub-quadratic. Further comparisons of large-signal transient simulations reveal the hydrodynamic model produces certain anomalous electron ensemble behaviors within the transistor structure. The fundamentally different electron dynamics produced by the two models suggest an underlying cause for their different numerical convergence characteristics.


  • Space charge waves in a two-dimensional electron gas

    by Peng Zhang, Patrick Wong, Yang Zhou, John D. Albrecht, Matt Hodek, David Smithe

    This paper uses field theory to derive the exact dispersion relation of space charge waves in a two-dimensional electron gas (2DEG) located in a dielectric or a dissimilar dielectric waveguide. It is found that the dispersion of a 2DEG can be modeled accurately using the free-electron sheet model, which is further confirmed by the almost identical polarizability of a 2DEG and of a free-electron sheet with zero drift velocity. Transitions among the well-known 2DEG dispersion, the beam mode in vacuum electronics, and Gould–Trivelpiece mode in plasma physics are demonstrated by varying the 2DEG density and direct current drift velocity. The effects of waveguide dimensions are also presented. Our method is general and can be applied to find the dispersion relation of 2DEG with arbitrary drift velocity (governed by electric field and scattering) in more complex circuits. Our study provides insight into the design of electromagnetic wave devices and circuits involving a 2DEG.


  • Flexible Chip-First Millimeter-Wave Packaging Using Multiple Dielectrics

    by Xenofon Konstantinou, John D. Albrecht, Premjeet Chahal, John Papapolymerou

    This article focuses on improving the robustness of fully additive manufactured packaging solutions for application-specific, millimeter-wave (mm-wave) system integration. We demonstrate two new chip-first packaging approaches that expand on the state-of-the-art by incorporating multiple dielectric materials. Our strategies not only exploit the flexibility and adaptability of the chip-first approach, but also offer solutions to potential die–dielectric adhesion problems that previous chip-first approaches encountered. To demonstrate our solution, we package 0- and 3-dB attenuators in a fully additive process to characterize the RF performance of the interconnect strategy with improved dielectric adhesion. These interconnects were measured up to 50 GHz and yield losses comparable to, or smaller than, previously demonstrated AM packages. Our approaches provide flexible, mm-wave-capable, and broadband packaging solutions for next-generation packaging technologies for high-stress and high-temperature applications.