Olexiy Yakovenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Olexiy Yakovenko has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr S. Roik
Chemical Faculty, Taras Shevchenko National University of Kyiv, Kyiv, Ukraine
12 shared publications - Natalia Valerievna Golovata
Chemical Department, Taras Shevchenko National University of Kyiv, Kyiv, Ukraine
9 shared publications - Volodymyr Kazimirov
Chemical Department, Taras Shevchenko National University of Kyiv, Kyiv, Ukraine
9 shared publications - Volodymyr Sokolskii
Chemical Department Taras Shevchenko National University of Kyiv Lva Tolstoho Street, 12 Kyiv Ukraine
3 shared publications G.M. Zelinskaya
G.V. Kurdymov Institute for Metal Physics, Nat. Acad. of Sci. of Ukraine, Kyiv, Ukraine
2 shared publicationsO.S. Muratov
Faculty of Biotechnology and Environmental Control, National University of Food Technologies, Kyiv, Ukraine
2 shared publications
Latest Publications
- 3 February 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1041, 59-69
Structure and Properties of Heat-Resistant FeNiCrCuAl High-Entropy Alloys
This study aimed to smelt high-entropy alloys (HEAs) composed of inexpensive and commonly available metallic elements using iron-based alloys, ligatures, and commercially pure metals, and to investigate their phase structure and heat-resistance. High-entropy alloys of the FeNiCrCuAl system were smelted in air using an induction furnace with a crucible lined with rammed neutral aluminum and magnesium oxides. The elements Fe, Ni, Cr, Cu, and Al were introduced via high-alloy cast iron, stainless steel grade GX10CrNiMn-18-9-1 (1.4541), industrial-grade low-carbon ferrochrome (FeCr70C1), binary Cu-33Al ligature, tough-pitch copper, and semi-finished nickel. Samples of the investigated alloys were prepared using lost foam and sand mold casting methods. Microstructural analysis revealed the presence of rounded dendritic branches, copper-rich interdendritic regions, and high-chromium carbides. The phase composition of the as-cast FeNiCrCuAl alloys consisted of multiple phases: solid solutions with a BCC structure ordered in the B2 type, an FCC structure, and complex carbides (FeCr) 7 C 3 . High-entropy alloys of the FeNiCrCuAl system, with increased aluminum and chromium content, can significantly outperform standard heat-resistant stainless steels in terms of oxidation resistance indicators – surface oxidation rate, and oxidation stability at 900°C and 1000°C. The specific oxidation of the high-entropy alloy FeNiCrCuAl, which contains at least 18 at. % chromium, was 0.1627 mg/cm² after a 4-hour exposure at 1000 °C. Under the same conditions, the specific oxidation of X2CrNi19-11 stainless steel (1.4306) was 0.6689 mg/cm².
- 3 February 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1041, 59-69
Structure and Properties of Heat-Resistant FeNiCrCuAl High-Entropy Alloys
This study aimed to smelt high-entropy alloys (HEAs) composed of inexpensive and commonly available metallic elements using iron-based alloys, ligatures, and commercially pure metals, and to investigate their phase structure and heat-resistance. High-entropy alloys of the FeNiCrCuAl system were smelted in air using an induction furnace with a crucible lined with rammed neutral aluminum and magnesium oxides. The elements Fe, Ni, Cr, Cu, and Al were introduced via high-alloy cast iron, stainless steel grade GX10CrNiMn-18-9-1 (1.4541), industrial-grade low-carbon ferrochrome (FeCr70C1), binary Cu-33Al ligature, tough-pitch copper, and semi-finished nickel. Samples of the investigated alloys were prepared using lost foam and sand mold casting methods. Microstructural analysis revealed the presence of rounded dendritic branches, copper-rich interdendritic regions, and high-chromium carbides. The phase composition of the as-cast FeNiCrCuAl alloys consisted of multiple phases: solid solutions with a BCC structure ordered in the B2 type, an FCC structure, and complex carbides (FeCr) 7 C 3 . High-entropy alloys of the FeNiCrCuAl system, with increased aluminum and chromium content, can significantly outperform standard heat-resistant stainless steels in terms of oxidation resistance indicators – surface oxidation rate, and oxidation stability at 900°C and 1000°C. The specific oxidation of the high-entropy alloy FeNiCrCuAl, which contains at least 18 at. % chromium, was 0.1627 mg/cm² after a 4-hour exposure at 1000 °C. Under the same conditions, the specific oxidation of X2CrNi19-11 stainless steel (1.4306) was 0.6689 mg/cm².
- 1 December 2025
- Published by Ivan Franko National University of Lviv in Journal of Physical Studies
- Vol. 29 (4)
Fabrication of multicomponent nanoporous metallic materials by vapor phase dealloying
- 1 December 2025
- Published by Ivan Franko National University of Lviv in Journal of Physical Studies
- Vol. 29 (4)
Fabrication of multicomponent nanoporous metallic materials by vapor phase dealloying
- 1 January 2025
- Published by Taras Shevchenko National University of Kyiv in Bulletin of Taras Shevchenko National University of Kyiv. Chemistry
- No. 1 (60),p. 76-80
LOCAL ATOMIC ARRANGEMENT OF Al — Fe 20 at. % — Sn MELTS
Background. Alloying of the aluminum-based antifriction materials enhances the wear resistance and thermal stability. Copper, cobalt, and chromium are widely used in the industry as additions to aluminum–tin alloys; however, there are no studies on the influence of iron in the scientific literature. The determination of the peculiarities of atomic ordering in Al–Fe–Sn melts should allow to predict the phase composition of the corresponding composites. Methods. The scattering curves of Al67Fe20Sn13, Al60Fe20Sn20 and Al52Fe20Sn20 melts have been obtained at 1500°C by means of X-ray diffraction. The structural models of melts have been reconstructed using Reverse Monte Carlo simulation, and statistical-geometric approach with Voronoi diagrams and Delaunay tessellations was applied for characterization. Results. The micro-inhomogeneous structure of Al80-xFe20Snx (x=13, 20, 28) melts at 1500°C was confirmed. After the analysis of the obtained structural models, the regularities of changes in the local environment of atoms with concentration were established. Conclusions. The possibility of the existence of the enriched in Fe and Sn phases in the aluminum matrix after solidification of the Al80-xFe20Snx alloys with low tin content has been demonstrated. Such phases have a negative impact on the operational characteristics of antifriction materials, therefore the compositions Al60Fe20Sn20 and Al52Fe20Sn28 are more preferable.
- 1 January 2025
- Published by Taras Shevchenko National University of Kyiv in Bulletin of Taras Shevchenko National University of Kyiv. Chemistry
- No. 1 (60),p. 76-80
LOCAL ATOMIC ARRANGEMENT OF Al — Fe 20 at. % — Sn MELTS
Background. Alloying of the aluminum-based antifriction materials enhances the wear resistance and thermal stability. Copper, cobalt, and chromium are widely used in the industry as additions to aluminum–tin alloys; however, there are no studies on the influence of iron in the scientific literature. The determination of the peculiarities of atomic ordering in Al–Fe–Sn melts should allow to predict the phase composition of the corresponding composites. Methods. The scattering curves of Al67Fe20Sn13, Al60Fe20Sn20 and Al52Fe20Sn20 melts have been obtained at 1500°C by means of X-ray diffraction. The structural models of melts have been reconstructed using Reverse Monte Carlo simulation, and statistical-geometric approach with Voronoi diagrams and Delaunay tessellations was applied for characterization. Results. The micro-inhomogeneous structure of Al80-xFe20Snx (x=13, 20, 28) melts at 1500°C was confirmed. After the analysis of the obtained structural models, the regularities of changes in the local environment of atoms with concentration were established. Conclusions. The possibility of the existence of the enriched in Fe and Sn phases in the aluminum matrix after solidification of the Al80-xFe20Snx alloys with low tin content has been demonstrated. Such phases have a negative impact on the operational characteristics of antifriction materials, therefore the compositions Al60Fe20Sn20 and Al52Fe20Sn28 are more preferable.
- 21 July 2023
- Published by Wiley in ChemistrySelect
- Vol. 8 (28)
Formation of the Short‐Range Order in Liquid Al−Ni−Sn Alloys
Short‐range order (SRO) in the liquid Al−Ni−Sn alloys has been investigated using the X‐ray diffraction method and Reverse Monte Carlo simulations. Obtained results point out a micro‐inhomogeneous structure of Al−Sn−Ni melts with Sn content between 10 and 65 at.% due to the presence of atomic clusters with the structure of liquid Sn and atomic clusters with Ni−Sn coordination. The influence of the atomic size ratio (size factor) and pair atomic interactions (energy factor) on the short‐range order of the investigated ternary melts are discussed. There is a competition between Al and Sn atoms in the formation of the SRO around Ni atoms due to the difference in bond energy in Ni−Al and Ni−Sn pairs. This competition, as well as a bigger radius of Sn atoms, results in the formation of atomic clusters with liquid Sn‐like local atomic structure.
- 21 July 2023
- Published by Wiley in ChemistrySelect
- Vol. 8 (28)
Formation of the Short‐Range Order in Liquid Al−Ni−Sn Alloys
Short‐range order (SRO) in the liquid Al−Ni−Sn alloys has been investigated using the X‐ray diffraction method and Reverse Monte Carlo simulations. Obtained results point out a micro‐inhomogeneous structure of Al−Sn−Ni melts with Sn content between 10 and 65 at.% due to the presence of atomic clusters with the structure of liquid Sn and atomic clusters with Ni−Sn coordination. The influence of the atomic size ratio (size factor) and pair atomic interactions (energy factor) on the short‐range order of the investigated ternary melts are discussed. There is a competition between Al and Sn atoms in the formation of the SRO around Ni atoms due to the difference in bond energy in Ni−Al and Ni−Sn pairs. This competition, as well as a bigger radius of Sn atoms, results in the formation of atomic clusters with liquid Sn‐like local atomic structure.
- 12 December 2022
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- Vol. 62 (4) , 701-709
High-temperature X-ray diffraction study of anorthite-tialite materials
- 12 December 2022
- Published by Taylor & Francis in Canadian Metallurgical Quarterly
- Vol. 62 (4) , 701-709
High-temperature X-ray diffraction study of anorthite-tialite materials
- 28 March 2022
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 586, 121562
Local atomic structure of liquid Al87Mg13 alloy
- 28 March 2022
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 586, 121562
Local atomic structure of liquid Al87Mg13 alloy
- 17 January 2022
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 60 (4) , 625-635
The short-range order in liquid Al-Co-Sn alloys
The short-range order (SRO) in the liquid Al-Co-Sn alloys has been investigated in a wide concentration range using XRD and RMC simulation. The influence of the atomic size ratio and pair atomic interactions on the SRO of investigated liquid alloys have been discussed. Three concentration regions with different local atomic structures have been found for Al-Co-Sn melts. At low tin content, the SRO is similar to Al-Co melts and Sn atoms were statistically distributed in the volume. At high Sn content, the local atomic structure is close to liquid tin with Al and Co atoms even distribution. The atomic clusters with a structure similar to liquid tin are formed due to competition between Al and Sn atoms in the formation of partial SRO of Co atoms and the difference in atomic sizes that complicates the inclusion of Sn atoms in the first coordination shell of the Al or Co.
- 17 January 2022
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 60 (4) , 625-635
The short-range order in liquid Al-Co-Sn alloys
The short-range order (SRO) in the liquid Al-Co-Sn alloys has been investigated in a wide concentration range using XRD and RMC simulation. The influence of the atomic size ratio and pair atomic interactions on the SRO of investigated liquid alloys have been discussed. Three concentration regions with different local atomic structures have been found for Al-Co-Sn melts. At low tin content, the SRO is similar to Al-Co melts and Sn atoms were statistically distributed in the volume. At high Sn content, the local atomic structure is close to liquid tin with Al and Co atoms even distribution. The atomic clusters with a structure similar to liquid tin are formed due to competition between Al and Sn atoms in the formation of partial SRO of Co atoms and the difference in atomic sizes that complicates the inclusion of Sn atoms in the first coordination shell of the Al or Co.
- 23 February 2021
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 59 (6) , 938-955
Comparative analysis of the short-range order in Al-Ge-Ni and Al-Ge-Fe melts
The comparative analysis of structure in ternary Al-Ge-Fe and Al-Ge-Ni melts has been performed in a wide concentration range using results of X-ray diffraction experiment and RMC simulations. The analysis of total S(Q) and partial SGe-Ge(Q) structure factors has shown that germanium atoms are present in two structural states: in the local environment of Fe(Ni) atoms and as part of clusters with structure of liquid germanium. Formation of these clusters is a result of displacement of Ge atoms outside the nearest environment of Fe(Ni) atoms due to competition effect between Al and Ge atoms. It has been established that ratio between partial nearest neighbour distances R1(Al-Ni)<R1(Al-Fe)<R1(Ge-Ni)<R1(Ge-Fe) is valid for all investigated melts due to the energy non-equivalence of the interatomic interactions. The influence of an intensity of interatomic interactions (energy factor) and implementation of dense non-crystalline packing (packing factor) on the SRO in the investigated ternary melts are discussed.
- 23 February 2021
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 59 (6) , 938-955
Comparative analysis of the short-range order in Al-Ge-Ni and Al-Ge-Fe melts
The comparative analysis of structure in ternary Al-Ge-Fe and Al-Ge-Ni melts has been performed in a wide concentration range using results of X-ray diffraction experiment and RMC simulations. The analysis of total S(Q) and partial SGe-Ge(Q) structure factors has shown that germanium atoms are present in two structural states: in the local environment of Fe(Ni) atoms and as part of clusters with structure of liquid germanium. Formation of these clusters is a result of displacement of Ge atoms outside the nearest environment of Fe(Ni) atoms due to competition effect between Al and Ge atoms. It has been established that ratio between partial nearest neighbour distances R1(Al-Ni)<R1(Al-Fe)<R1(Ge-Ni)<R1(Ge-Fe) is valid for all investigated melts due to the energy non-equivalence of the interatomic interactions. The influence of an intensity of interatomic interactions (energy factor) and implementation of dense non-crystalline packing (packing factor) on the SRO in the investigated ternary melts are discussed.
- 28 November 2018
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 58 (1) , 94-104
Formation of short-range order in Al–Ge–Fe melts: influence of composition
The short-range order in Al–Ge–Fe melts has been studied by X-ray diffraction and reverse Monte Carlo simulations in wide concentration range. Influence of the replacement of one component by another while the content of third component is constant on the formation of a local structure of ternary melts has been discussed. It has been shown that at Ge content less than 30 аt. % Ge atoms are uniformly distributed in the volume of the Al–Ge–Fe melts and atomic clusters with structure similar to the liquid germanium are formed at content more than 30 аt. % Ge. The addition of the third component (Ge or Al) to the binary Al–Fe or Fe–Ge melts, correspondingly, results in competition between Al and Ge atoms in formation of the local structure around Fe atoms. The obtained concentration dependences of the nearest neighbour distances point out that the ternary interactions take place in the Al–Fe–Ge melts.
- 28 November 2018
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 58 (1) , 94-104
Formation of short-range order in Al–Ge–Fe melts: influence of composition
The short-range order in Al–Ge–Fe melts has been studied by X-ray diffraction and reverse Monte Carlo simulations in wide concentration range. Influence of the replacement of one component by another while the content of third component is constant on the formation of a local structure of ternary melts has been discussed. It has been shown that at Ge content less than 30 аt. % Ge atoms are uniformly distributed in the volume of the Al–Ge–Fe melts and atomic clusters with structure similar to the liquid germanium are formed at content more than 30 аt. % Ge. The addition of the third component (Ge or Al) to the binary Al–Fe or Fe–Ge melts, correspondingly, results in competition between Al and Ge atoms in formation of the local structure around Fe atoms. The obtained concentration dependences of the nearest neighbour distances point out that the ternary interactions take place in the Al–Fe–Ge melts.
- 3 February 2017
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 56 (1) , 43-54
The relationship between thermodynamic properties and local atomic structure of Al-TM (TM = Mn, Fe, Co, Ni, Cu) melts
The relationship between structure and thermodynamic properties of Al- transition metal (TM) (TM = Mn, Fe, Co, Ni, Cu) melts had been studied by using the results of X-ray diffraction experiments, reverse Monte Carlo simulations and the model of ideal associated solution (MIAS). It was considered that local atomic structure of melts is determined by dense non-crystalline atomic packing and energy of interatomic interactions. This allowed to choose the types of associates for the MIAS. It is shown that the prominent role of the atomic packing factor in the Al-Mn, Al-Fe melts leads to correlation between the local atomic ordering of melts and the one of relevant polytetrahedral phases and defines a set of associates. Strengthening of heteroatomic interactions in the Al-Co, Al-Ni melts leads to an increase of the energy factor role in determining their structure and properties that reduces the number of associates from three for the Al-Mn melts to one for the Al-Ni.
- 3 February 2017
- Published by Taylor & Francis in Physics and Chemistry of Liquids
- Vol. 56 (1) , 43-54
The relationship between thermodynamic properties and local atomic structure of Al-TM (TM = Mn, Fe, Co, Ni, Cu) melts
The relationship between structure and thermodynamic properties of Al- transition metal (TM) (TM = Mn, Fe, Co, Ni, Cu) melts had been studied by using the results of X-ray diffraction experiments, reverse Monte Carlo simulations and the model of ideal associated solution (MIAS). It was considered that local atomic structure of melts is determined by dense non-crystalline atomic packing and energy of interatomic interactions. This allowed to choose the types of associates for the MIAS. It is shown that the prominent role of the atomic packing factor in the Al-Mn, Al-Fe melts leads to correlation between the local atomic ordering of melts and the one of relevant polytetrahedral phases and defines a set of associates. Strengthening of heteroatomic interactions in the Al-Co, Al-Ni melts leads to an increase of the energy factor role in determining their structure and properties that reduces the number of associates from three for the Al-Mn melts to one for the Al-Ni.