SRSylvain Ranvier

Sylvain Ranvier

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sylvain Ranvier has a total of 269 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    DUSTER: Dust Study, Transport, and Electrostatic Removal for Exploration Missions

    by Sylvain Ranvier, Karolien Lefever, Jean-Charles Matéo Vélez, Gian Paolo Candini, Michel Anciaux, Rémi Pacaud, Carmen Pastor Morales, Rosario Sanz Mesa, Sophie Berkenbosch, Sébastien Hess, et al.

    1. The importance of studying lunar dust particlesInternational scientific and commercial interests in exploration missions to solar system bodies such as the Moon, asteroids and comets have increased significantly during the last two decades and will continue to increase in the future. One major environmental constraint during exploration missions is the presence of charged dust-like particles. They can be a threat for both human and robotic exploration missions.The effects of lunar dust on Extra-Vehicular Activity systems can take many forms such as external vision obscuration, false instrument readings, dust coating and contamination, loss of traction, clogging of mechanisms, abrasion, thermal control problems and seal failures. One of the most serious effects is the compromising of astronaut health by irritation and inhalation of lunar dust.Therefore, it is of utmost importance to characterise the properties of the dust particles present on the exploration sites and their transportation mechanisms to enable efficient mitigation techniques to be put in place. The main objective of DUSTER (Dust Study, Transport, and Electrostatic Removal for Exploration Missions) is to investigate in detail the charging and cohesion of the dust grain in the regolith. The project addresses key questions about the surfacing of airless bodies as observed by telescopes and scientific probes, such as the formation of dust ponds and the dust haze at the limb of the moon observed by the astronaut during the Apollo missions. It also addresses more engineering-oriented concerns regarding the adhesion of dust particles to man-made surfaces (spacecraft, instruments, spacesuits, solar panels, etc.).The goal of DUSTER is to develop the instrumentation and technologies for in situ analysis of the electrical charging and transport of those dust particles. In addition, the project aims at developing a ground based test facility to validate the instrument in representative conditions and improve dust charging and transportation models. 2. The DUSTER instrumentGiven that the surface gravity as well as the UV and soft X-ray fluxes, which are drivers for the electrical charging of the dust, can be obtained by existing measurement data or reliable modelling, those two physical quantities do not need to be measured by the instrument. The remaining parameters that are needed to quantify dust charging and electrostatic transportation are the level of charging, the ambient plasma and the current resulting from the displacement of the dust particles.The level of charging is assessed by measuring the electric field above the dust layer with a DC E-Field probe and using the Gauss theorem. The ambient plasma parameters (electron density and temperature) are measured with a Langmuir probe. To study the dust particles displacement, a Faraday cup (FC) is placed above the dust layer. When a voltage is applied to the FC (up to several kV), this creates an E-field that applies a force on the charged particles. When the voltage is high enough, the charged particles are attracted inside the FC. By measuring the resulting current from the FC the amount of charged dust that has been moved can be quantified.The block diagram of the multi-sensor instrument is depicted in Fig. 1. It includes three front ends with specific probes/electrodes.Fig. 1. Block diagram of the instrument.The instrument prototype will be entirely designed by the members of the consortium. The electronics will include a Data Processing Unit (DPU), based on a FPGA design running a Leon3 microprocessor, and a Low Voltage Power Supply (LVPS) as main power interface for the instrument, both designed and built at IAA-CSIC. The very sensitive front ends which will acquire the readings and the High Voltage Power Supply (HVPS) are designed and built at BIRA-IASB. The probes/electrodes are designed and built at ONERA and BIRA-IASB.The application software to control the instrument, implement the science sequences, acquire the data obtained from the probes, process it and send it through the spacecraft interface is developed at IAA-CSIC. The EMC tests will be carried out by TAS-E. 3. Preliminary results obtained with a dedicated laboratory test setupThe laboratory test setup is built on the existing DROP chamber at ONERA Toulouse, France (see Fig. 2). It is a vacuum chamber that allows irradiating the dust particles with a VUV lamp, includes a Kelvin probe to infer the charging level of the dust layer and accommodates an FC that is used to attract the dust particles and measure the current resulting from the displacement of the charges.Fig. 2. DROP chamber at ONERA Toulouse, France.An example of the measured signal from the FC when biased at 3 kV is depicted in Fig. 3. It shows that several charged dust grains (or aggregates of grains) are mobilised.Fig. 3. Output voltage of the transimpedance amplifier as a function of the polarization time of the detector. The background noise is depicted in dark and the dust grain detection is highlighted in red. The detector is polarized at +3 kV after 5 minutes of VUV irradiation. Fig. 4. Zoom in of the peaks at 18 seconds in Fig. 3. It shows a clear pair of two consecutive peaks of opposite polarity, indicating that the dust grain entered into the FC and then fell back onto the sample holder. This project is funded by the European Union’s HORIZON Research and Innovation programme under grant agreement No 101082466. Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or the granting authority. Neither the European Union nor the granting authority can be held responsible for them.


  • Top Cited Papers
    Open Access

    The Comet Interceptor Mission

    by Geraint H. Jones, Colin Snodgrass, Cecilia Tubiana, Michael Küppers, Hideyo Kawakita, Luisa M. Lara, Jessica Agarwal, Nicolas André, Nicholas Attree, Uli Auster, et al.

    Here we describe the novel, multi-point Comet Interceptor mission. It is dedicated to the exploration of a little-processed long-period comet, possibly entering the inner Solar System for the first time, or to encounter an interstellar object originating at another star. The objectives of the mission are to address the following questions: What are the surface composition, shape, morphology, and structure of the target object? What is the composition of the gas and dust in the coma, its connection to the nucleus, and the nature of its interaction with the solar wind? The mission was proposed to the European Space Agency in 2018, and formally adopted by the agency in June 2022, for launch in 2029 together with the Ariel mission. Comet Interceptor will take advantage of the opportunity presented by ESA’s F-Class call for fast, flexible, low-cost missions to which it was proposed. The call required a launch to a halo orbit around the Sun-Earth L2 point. The mission can take advantage of this placement to wait for the discovery of a suitable comet reachable with its minimum $\varDelta $ Δ V capability of $600\text{ ms}^{-1}$ 600  ms − 1 . Comet Interceptor will be unique in encountering and studying, at a nominal closest approach distance of 1000 km, a comet that represents a near-pristine sample of material from the formation of the Solar System. It will also add a capability that no previous cometary mission has had, which is to deploy two sub-probes – B1, provided by the Japanese space agency, JAXA, and B2 – that will follow different trajectories through the coma. While the main probe passes at a nominal 1000 km distance, probes B1 and B2 will follow different chords through the coma at distances of 850 km and 400 km, respectively. The result will be unique, simultaneous, spatially resolved information of the 3-dimensional properties of the target comet and its interaction with the space environment. We present the mission’s science background leading to these objectives, as well as an overview of the scientific instruments, mission design, and schedule.


  • Open Access

    Laboratory measurements of the performances of the Sweeping Langmuir Probe instrument aboard the PICASSO CubeSat

    by Sylvain Ranvier, Jean-Pierre Lebreton

    The Sweeping Langmuir Probe (SLP) is one of the instruments on board the triple-unit CubeSat PICASSO, an ESA in-orbit demonstrator launched in September 2020, which is flying at about 540 km altitude. SLP comprises four small cylindrical probes mounted at the tip of the solar panels. It aims to perform in situ measurements of the plasma parameters (electron density and temperature together with ion density) and of the spacecraft potential in the ionosphere. Before the launch, the instrument, accommodated on an electrically representative PICASSO mock-up, was tested in a plasma chamber. It is shown that the traditional orbital-motion-limited collection theory used for cylindrical Langmuir probes cannot be applied directly for the interpretation of the measurements because of the limited dimensions of the probes with respect to the Debye length in the ionosphere. Nevertheless, this method can be adapted to take into account the short length of the probes. To reduce the data downlink while keeping the most important information in the current-voltage characteristics, SLP includes an on-board adaptive sweeping capability. This functionality has been validated in both the plasma chamber and in space, and it is demonstrated that with a reduced number of data points the electron retardation and electron saturation regions can be well resolved. Finally, the effect of the contamination of the probe surface, which can be a serious issue in Langmuir probe data analysis, has been investigated. If not accounted for properly, this effect could lead to substantial errors in the estimation of the electron temperature.


  • Open Access

    First results from the Sweeping Langmuir Probe (SLP) instrument on board PICASSO

    by Sylvain Ranvier, Johan De Keyser, Jean-Pierre Lebreton

    The Sweeping Langmuir Probe (SLP) instrument on board the Pico-Satellite for Atmospheric and Space Science Observations (PICASSO) has been developed at the Royal Belgian Institute for Space Aeronomy.  PICASSO, an ESA in-orbit demonstrator launched in September 2020, is a triple unit CubeSat orbiting at about 540 km altitude with 97 degrees inclination. The SLP instrument includes four independent cylindrical probes that are used to measure the plasma density and electron temperature as well as the floating potential of the spacecraft. Along the orbit of PICASSO the plasma density is expected to fluctuate over a wide range, from about 1e8/m3 at high latitude up to more than 1e12/m3 at low/mid latitude. SLP can measure plasma density from 1e8/m3 to 1e13/m3. The electron temperature is expected to lie between approximately 1000 K and 10.000 K. Given the high inclination of the orbit, SLP will allow a global monitoring of the ionosphere. Using the traditional sweeping mode, the maximum spatial resolution is of the order of a few hundred meters for the plasma density, electron temperature and spacecraft potential. With the fixed-bias mode, the electron density can be measured with a spatial resolution of about 1.5 m. The main goals are to study the ionosphere-plasmasphere coupling, the subauroral ionosphere and corresponding magnetospheric features together with auroral structures and polar caps, by combining SLP data with other complementary data sources (space- or ground-based instruments). The first results from SLP will be presented.

  • Open Access

    DUSTER: a multi-sensor instrument to study dust transport and electrostatic removal for exploration missions

    by Sylvain Ranvier, Sebastien Hess, Jean-Charles Mateo Velez, Angel Alvaro Sanchez, Johan De Keyser

    One major environmental constraint during exploration missions is the presence of charged dust-like particles, which are present on the Moon, Mars, comets and asteroids. From an analysis of the effects of lunar dust on Extra-Vehicular Activity (EVA) systems during the six Apollo missions that landed on the lunar surface, it was found that these effects can take many forms such as external vision obscuration, false instrument readings, dust coating and contamination, loss of traction, clogging of mechanisms, abrasion, thermal control problems and seal failures. One of the most serious effects is the compromising of astronaut health by irritation and inhalation of lunar dust.Therefore, it is of utmost importance to characterise the properties of the dust particles present on the exploration sites and their transportation mechanisms to enable efficient mitigation techniques to be put in place.The overall objective of the DUSTER project is to develop instrumentation and technologies to study dust particles and electrostatic transportation for planetary and small body exploration missions. Specifically, the aim is to design, manufacture and test in a relevant environment a compact multi-sensor instrument for in situ analysis of dust properties (mechanical and electrical) and electrostatic transportation that can be used on a small lunar lander. To that end, the instrument includes:- A dust collector: electrodes biased at high potential to attract/collect dust particles, coupled to an electrometer- Langmuir probes- E-field probesUsing this instrument, the following parameters will be derived:- Charging level of dust as a function of the environmental parameters (illumination, plasma density and temperature)- (gravity + cohesive forces)/charge ratio distribution of dust layerThese two parameters will allow the determination of the electric field needed to attract/collect dust according to the environmental conditions (illumination, plasma density and temperature), which, among other applications, will allow designing electrostatic dust mitigation devices and dust sample collectors.

  • Open Access

    Validation and characterisation of the Sweeping Langmuir Probe (SLP) instrument for the PICASSO mission

    by Sylvain Ranvier, Michel Anciaux, Jean-Pierre Lebreton, Johan De Keyser

    The Sweeping Langmuir Probe (SLP) instrument, that uses a novel measurement technique to take into account spacecraft charging effects, has been developed at the Royal Belgian Institute for Space Aeronomy. SLP will fly on board the ESA scientific in-orbit demonstrator PICASSO together with the hyper-spectral imager VISION. PICASSO, a triple unit CubeSat, will be launched in March 2020. The goal of the mission is to prove the feasibility of performing true science (with limited extent) with a nano-satellite and demonstrate the very low cost / science ratio with respect to big missions. SLP will allow a global monitoring of the ionosphere with a maximum spatial resolution of the order of 150 m.  The main goals are to study the ionosphere-plasmasphere coupling, the subauroral ionosphere and corresponding magnetospheric features together with auroral structures and polar caps, by combining SLP data with other complementary data sources (space- or ground-based instruments). SLP can measure plasma density from 1e8/m³ up to 1e13/m³ and electron temperature up to 15 000 K. We will present the main results from the validation tests performed in the plasma chamber at ESTEC together with comparisons with particle-in-cell (PIC) simulations performed with SPIS (Spacecraft Plasma Interaction System).

  • Open Access

    The Source Regions of Whistlers

    by Dávid Koronczay, János Lichtenberger, Mark A. Clilverd, Craig J. Rodger, Stefan I. Lotz, Dmitry V. Sannikov, Nina V. Cherneva, Tero Raita, Fabien Darrouzet, Sylvain Ranvier, et al.

    We present a new method for identifying the source regions of lightning‐generated whistlers observed at a fixed location. In addition to the spatial distribution of causative lightning discharges, we calculate the ratio of lightning discharges transmitted into ground detectable whistlers as a function of location. Our method relies on the time of the whistlers and the time and source location of spherics from a global lightning database. We apply this method to whistlers recorded at 15 ground‐based stations in the Automatic Whistler Detector and Analyzer Network operating between 2007 and 2018 and to located lightning strokes from the World Wide Lightning Location Network database. We present the obtained maps of causative lightning and transmission rates. Our results show that the source region of whistlers corresponding to each ground station is around the magnetic conjugate point of the respective station. The size of the source region is typically less than 2,000 km in radius with a small fraction of sources extending to up to 3,500 km. The transmission ratio is maximal at the conjugate point and decreases with increasing distance from it. This conforms to the theory that whistlers detected on the ground propagated in a ducted mode through the plasmasphere, and thus, the lightning strokes of their causative spherics must cluster around the footprint of the ducts in the other hemisphere. Our method applied resolves the whistler excitation region mystery that resulted from correlation‐based analysis methods, concerning the source region of whistlers detected in Dunedin, New Zealand.


  • LEO Charging of the PICASSO Cubesat and Simulation of the Langmuir Probes Operation

    by Andreas Waets, Fabrice Cipriani, Sylvain Ranvier

    The sweeping Langmuir probe (SLP) instrument is a payload of the European Space Agency's (ESA) in-orbit demonstrator PicoSatellite for Atmospheric and Space Science Observations (PICASSO) cubesat, measuring the plasma environment in a high-inclination low earth orbit (LEO) orbit. Because of the small size of the spacecraft (0.3 m x 0.1 m x 0.1 m), the spacecraft floating potential can significantly drift when sweeping the probe bias voltage, affecting the current-voltage characteristic from which plasma parameters are retrieved. In LEO, the spacecraft generally encounters a high-density, cold (less than 1 eV) plasma environment, but due to the high orbital inclination, PICASSO passes the auroral regions exposing the spacecraft to precipitating fluxes of hot (several kiloelectron volts) electrons with potentially harmful, high-level spacecraft charging as a result. To investigate the spacecraft charging and the in-orbit operation of the Langmuir probes in both of these regimes, simulations of PICASSO were carried out in Spacecraft Plasma Interaction System (SPIS). The conditions of the LEO plasma and the constraints imposed by the particle-in-cell (PIC) models on the mesh size make this type of plasma simulations a very challenging task.


  • Use of a Langmuir Probe Instrument on Board a Pico-Satellite

    by Sylvain Ranvier, Michel Anciaux, Pepijn Cardoen, Emmanuel Gamby, Ir Sabrina Bonnewijn, Johan De Keyser, Didier Pieroux, J. P. Lebreton

    The sweeping Langmuir probe instrument is a part of the payload of PICo-satellite for atmospheric and space science observations (PICASSO), an ESA in-orbit demonstrator. It includes four thin cylindrical probes whose electrical potential is swept to measure both plasma density and electron temperature together with the spacecraft (S/C) potential. PICASSO is a triple unit CubeSat of dimensions 340.5 mm×100 mm×100 mm. The orbit is expected to be a high inclination low-earth orbit. The main issue implied by the use of a pico-satellite platform for a Langmuir probe instrument is the limited conducting area of the S/C, which leads to S/C charging and drift of the instrument's electrical ground during the measurement. A specific measurement technique that includes the simultaneous measurement of the potential and current of different probes has been developed to retrieve consistent current-voltage characteristics that can be used to estimate the plasma parameters mentioned above.