Leon M. Dean
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Leon M. Dean has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
Christopher M. Bates
5 shared publicationsJulia D. Cushen
5 shared publications- Carlton Grant Willson
The Univ. of Texas at Austin (United States)
4 shared publications Christopher J. Ellison
4 shared publicationsMichael J. Maher
4 shared publicationsWilliam J. Durand
4 shared publications
Latest Publications
- 5 September 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 168
Surface pattern formation induced by oscillatory loading of frontally polymerized gels
- 5 September 2022
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 168
Surface pattern formation induced by oscillatory loading of frontally polymerized gels
- Open Access
- 14 May 2021
- Published by Springer Nature in Nature Communications
- Vol. 12 (1) , 1-9
Rapid synchronized fabrication of vascularized thermosets and composites
Bioinspired vascular networks transport heat and mass in hydrogels, microfluidic devices, self-healing and self-cooling structures, filters, and flow batteries. Lengthy, multistep fabrication processes involving solvents, external heat, and vacuum hinder large-scale application of vascular networks in structural materials. Here, we report the rapid (seconds to minutes), scalable, and synchronized fabrication of vascular thermosets and fiber-reinforced composites under ambient conditions. The exothermic frontal polymerization (FP) of a liquid or gelled resin facilitates coordinated depolymerization of an embedded sacrificial template to create host structures with high-fidelity interconnected microchannels. The chemical energy released during matrix polymerization eliminates the need for a sustained external heat source and greatly reduces external energy consumption for processing. Programming the rate of depolymerization of the sacrificial thermoplastic to match the kinetics of FP has the potential to significantly expedite the fabrication of vascular structures with extended lifetimes, microreactors, and imaging phantoms for understanding capillary flow in biological systems.
- 14 May 2021
- Published by Springer Nature in Nature Communications
- Vol. 12 (1) , 1-9
Open AccessRapid synchronized fabrication of vascularized thermosets and composites
Bioinspired vascular networks transport heat and mass in hydrogels, microfluidic devices, self-healing and self-cooling structures, filters, and flow batteries. Lengthy, multistep fabrication processes involving solvents, external heat, and vacuum hinder large-scale application of vascular networks in structural materials. Here, we report the rapid (seconds to minutes), scalable, and synchronized fabrication of vascular thermosets and fiber-reinforced composites under ambient conditions. The exothermic frontal polymerization (FP) of a liquid or gelled resin facilitates coordinated depolymerization of an embedded sacrificial template to create host structures with high-fidelity interconnected microchannels. The chemical energy released during matrix polymerization eliminates the need for a sustained external heat source and greatly reduces external energy consumption for processing. Programming the rate of depolymerization of the sacrificial thermoplastic to match the kinetics of FP has the potential to significantly expedite the fabrication of vascular structures with extended lifetimes, microreactors, and imaging phantoms for understanding capillary flow in biological systems.
- 24 May 2017
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 6 (6) , 609-612
Alkyl Phosphite Inhibitors for Frontal Ring-Opening Metathesis Polymerization Greatly Increase Pot Life
Frontal ring-opening metathesis polymerization (FROMP) has potential for use in rapid fabrication of structural polymers. However, the high activity of the ruthenium catalyst used for FROMP has limited the working time to <1 h. We report the use of alkyl phosphites as inhibitors for Grubbs’ type catalysts to substantially extend working time. Subtle changes in alkyl phosphite structure are shown to impact both pot life and frontal velocity. Specifically, by varying phosphite structure and concentration, we are able to control pot life between 0.25 and 30 h while still allowing FROMP to proceed at velocities between 1 and 8 cm/min to yield fully cured thermoset polymers. These results are of interest for conventional ROMP synthesis and may open the way to new FROMP-based manufacturing possibilities.
- 24 May 2017
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 6 (6) , 609-612
Alkyl Phosphite Inhibitors for Frontal Ring-Opening Metathesis Polymerization Greatly Increase Pot Life
Frontal ring-opening metathesis polymerization (FROMP) has potential for use in rapid fabrication of structural polymers. However, the high activity of the ruthenium catalyst used for FROMP has limited the working time to <1 h. We report the use of alkyl phosphites as inhibitors for Grubbs’ type catalysts to substantially extend working time. Subtle changes in alkyl phosphite structure are shown to impact both pot life and frontal velocity. Specifically, by varying phosphite structure and concentration, we are able to control pot life between 0.25 and 30 h while still allowing FROMP to proceed at velocities between 1 and 8 cm/min to yield fully cured thermoset polymers. These results are of interest for conventional ROMP synthesis and may open the way to new FROMP-based manufacturing possibilities.
- 27 January 2014
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 26 (3) , 1471-1479
Interfacial Design for Block Copolymer Thin Films
- 27 January 2014
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 26 (3) , 1471-1479
Interfacial Design for Block Copolymer Thin Films
- 1 January 2013
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 26 (2) , 223-224
Polarity-switching Top Coats for Silicon-containing Block Copolymer Orientation Control
- 1 January 2013
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 26 (2) , 223-224
Polarity-switching Top Coats for Silicon-containing Block Copolymer Orientation Control
- 9 November 2012
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 338 (6108) , 775-779
Polarity-Switching Top Coats Enable Orientation of Sub–10-nm Block Copolymer Domains
Thermally Transforming Thin Films: Nanoscale features can be created by the phase separation that occurs in block copolymers that join together polymer segments with different wetting properties. For applications such as lithography, it is useful to generate small features and to orient them through simple processing steps. Top-layer coatings should be able to help drive alignment, but it is difficult to coat a layer that also has strong enough interactions to influence assembly. Bates et al. (p. 775 ) developed a water-soluble polymer that can top-coat lamellaforming block copolymers and that transforms during thermal annealing into a neutral wetting layer that helps drive the formation of vertically oriented lamellae.
- 9 November 2012
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 338 (6108) , 775-779
Polarity-Switching Top Coats Enable Orientation of Sub–10-nm Block Copolymer Domains
Thermally Transforming Thin Films: Nanoscale features can be created by the phase separation that occurs in block copolymers that join together polymer segments with different wetting properties. For applications such as lithography, it is useful to generate small features and to orient them through simple processing steps. Top-layer coatings should be able to help drive alignment, but it is difficult to coat a layer that also has strong enough interactions to influence assembly. Bates et al. (p. 775 ) developed a water-soluble polymer that can top-coat lamellaforming block copolymers and that transforms during thermal annealing into a neutral wetting layer that helps drive the formation of vertically oriented lamellae.
- 19 October 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (21) , 8722-8728
Thin Film Self-Assembly of Poly(trimethylsilylstyrene-b-d,l-lactide) with Sub-10 nm Domains
- 19 October 2012
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 45 (21) , 8722-8728
Thin Film Self-Assembly of Poly(trimethylsilylstyrene-b-d,l-lactide) with Sub-10 nm Domains
- 12 October 2012
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 51 (2) , 290-297
Synthesis and thin‐film orientation of poly(styrene‐block‐trimethylsilylisoprene)
The successful synthesis, characterization, and directed self‐assembly of a silicon‐containing block copolymer, poly(styrene‐block‐trimethylsilylisoprene) (P(S‐b‐TMSI)), which has much higher oxygen etch contrast than thede factostandard, poly(styrene‐block‐methyl methacrylate) is reported. A Sakurai, Grignard‐type coupling reaction provided the key monomer in good yield. Living anionic polymerization was employed to prepare the block copolymer, which has very low polydispersity. P(S‐b‐TMSI) was successfully ordered and oriented by directed self‐assembly. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013
- 12 October 2012
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 51 (2) , 290-297
Synthesis and thin‐film orientation of poly(styrene‐block‐trimethylsilylisoprene)
The successful synthesis, characterization, and directed self‐assembly of a silicon‐containing block copolymer, poly(styrene‐block‐trimethylsilylisoprene) (P(S‐b‐TMSI)), which has much higher oxygen etch contrast than thede factostandard, poly(styrene‐block‐methyl methacrylate) is reported. A Sakurai, Grignard‐type coupling reaction provided the key monomer in good yield. Living anionic polymerization was employed to prepare the block copolymer, which has very low polydispersity. P(S‐b‐TMSI) was successfully ordered and oriented by directed self‐assembly. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013
- Open Access
- 1 January 2012
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 25 (1) , 125-130
Block Copolymer Orientation Control Using a Top-Coat Surface Treatment
- 1 January 2012
- Published by Technical Association of Photopolymers, Japan in Journal of Photopolymer Science and Technology
- Vol. 25 (1) , 125-130
Open AccessBlock Copolymer Orientation Control Using a Top-Coat Surface Treatment