Roger Raman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Roger Raman has a total of 899 co-authors. Here are the top co-authors by number of shared publications:
- Thomas R. Jarboe
Department of Aeronautics and Astronautics, University of Washington , Seattle, Washington 98195, USA
44 shared publications D. Mueller
35 shared publications- Jonathan Edward Menard
Princeton Plasma Physics Laboratory, Princeton, NJ, USA
30 shared publications M. Ono
25 shared publications- Vsevolod A Soukhanovskii
Lawrence Livermore National Laboratory
24 shared publications - Rajesh Maingi
Princeton Plasma Physics Laboratory
22 shared publications
Latest Publications
- 1 October 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (10)
Spectroscopic measurements of chromium atom and ion densities in coaxial helicity injection plasmas on QUEST
The densities of chromium atoms and ions in coaxial helicity injection plasmas on QUEST, a spherical tokamak with a major radius of 0.68 m and a minor radius of 0.40 m, were measured using optical emission spectroscopy. Effective electron temperatures and densities were evaluated from the ratios of chord-integrated Balmer line intensities using a collisional–radiative model, yielding values of approximately 3 eV and 3.6 × 1019 m−3 near the electrodes during the early phase and 12 eV and 1.4 × 1018 m−3 in the confinement region during the closed flux surface (CFS) formation phase. Using these plasma parameters and the chord-integrated intensities of Cr I, Cr II, and C II lines, the chord-averaged densities of chromium atoms and Cr+ and C+ ions were estimated. The chromium atom density near the electrodes during the early phase was approximately 8 × 1012 m−3. The estimated ionization mean free path indicated that chromium atoms are ionized primarily near the electrodes. Cr+ ions were inferred to be transported into the confinement region by the upward plasma flow. The resulting Cr+ ion density during the CFS formation phase was approximately 1 × 1017 m−3, and the C+ ion density was of the same order of magnitude. These results provide insight into the ionization and transport of electrode-derived metallic impurities.
- 1 October 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (10)
Spectroscopic measurements of chromium atom and ion densities in coaxial helicity injection plasmas on QUEST
The densities of chromium atoms and ions in coaxial helicity injection plasmas on QUEST, a spherical tokamak with a major radius of 0.68 m and a minor radius of 0.40 m, were measured using optical emission spectroscopy. Effective electron temperatures and densities were evaluated from the ratios of chord-integrated Balmer line intensities using a collisional–radiative model, yielding values of approximately 3 eV and 3.6 × 1019 m−3 near the electrodes during the early phase and 12 eV and 1.4 × 1018 m−3 in the confinement region during the closed flux surface (CFS) formation phase. Using these plasma parameters and the chord-integrated intensities of Cr I, Cr II, and C II lines, the chord-averaged densities of chromium atoms and Cr+ and C+ ions were estimated. The chromium atom density near the electrodes during the early phase was approximately 8 × 1012 m−3. The estimated ionization mean free path indicated that chromium atoms are ionized primarily near the electrodes. Cr+ ions were inferred to be transported into the confinement region by the upward plasma flow. The resulting Cr+ ion density during the CFS formation phase was approximately 1 × 1017 m−3, and the C+ ion density was of the same order of magnitude. These results provide insight into the ionization and transport of electrode-derived metallic impurities.
- Open Access
- 1 July 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (7) , 076053
Current ramp-up studies for NSTX-U in support of the development of non-inductive current ramp-up scenarios in STs
The Spherical Tokamak (ST) is a low-aspect-ratio tokamak projected to enable simultaneous operation at high normalized toroidal beta and high bootstrap current fraction. However, a compact ST reactor cannot be built with a full-sized solenoid. The remaining current required for sustained operation must be ramped up non-inductively. Sustained 100% non-inductive current drive at the MA level has not yet been demonstrated on an ST. Non-inductive current ramp-up is therefore a more challenging objective that the NSTX-U research program aims to address. In support of this development, free-boundary TRANSP simulations have been used to develop a current ramp-up scenario in which a significant fraction of the current is driven non-inductively by a combination of neutral-beam and bootstrap current drive. The resulting discharge has properties favorable for non-inductive current drive, such as a low normalized internal plasma inductance of approximately 0.45, a minimum safety factor exceeding 2, and a slightly reversed-shear q -profile. In these discharges, the plasma current ramps to 900 kA within 250 ms in an L-mode configuration, with varying electron density and density profiles. These discharges should be suitable for next-step NSTX-U experiments aimed at generating a robust L-mode fiducial scenario with low central solenoid flux consumption, which could be progressively improved as new NSTX-U experimental discharges are developed.
- 1 July 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (7) , 076053
Open AccessCurrent ramp-up studies for NSTX-U in support of the development of non-inductive current ramp-up scenarios in STs
The Spherical Tokamak (ST) is a low-aspect-ratio tokamak projected to enable simultaneous operation at high normalized toroidal beta and high bootstrap current fraction. However, a compact ST reactor cannot be built with a full-sized solenoid. The remaining current required for sustained operation must be ramped up non-inductively. Sustained 100% non-inductive current drive at the MA level has not yet been demonstrated on an ST. Non-inductive current ramp-up is therefore a more challenging objective that the NSTX-U research program aims to address. In support of this development, free-boundary TRANSP simulations have been used to develop a current ramp-up scenario in which a significant fraction of the current is driven non-inductively by a combination of neutral-beam and bootstrap current drive. The resulting discharge has properties favorable for non-inductive current drive, such as a low normalized internal plasma inductance of approximately 0.45, a minimum safety factor exceeding 2, and a slightly reversed-shear q -profile. In these discharges, the plasma current ramps to 900 kA within 250 ms in an L-mode configuration, with varying electron density and density profiles. These discharges should be suitable for next-step NSTX-U experiments aimed at generating a robust L-mode fiducial scenario with low central solenoid flux consumption, which could be progressively improved as new NSTX-U experimental discharges are developed.
- Top Cited PapersOpen Access
- 15 January 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (3)
Spherical tokamak physics research in preparation for the operation of NSTX-U
The National Spherical Torus Experiment Upgrade (NSTX-U) is preparing to resume operation, representing a crucial step toward realizing compact, cost-effective fusion pilot plants (FPPs). In advance of this, extensive modeling and data analysis have been conducted to advance the physics basis for low-aspect-ratio, high-performance plasma regimes, focusing on three core objectives: confinement and stability, power and particle handling, and steady-state operation. Significant progress has been made in understanding the electron temperature flattening in high-β plasmas, which is shown to be driven by a complex interplay of MHD instabilities (e.g., non-resonant infernal modes), fast-ion-driven Alfvén eigenmodes, and electron and ion-scale micro-instabilities, particularly Kinetic Ballooning Modes (KBMs), whose destabilization is strongly dependent on parallel magnetic field fluctuations (δB ‖ ). Furthermore, a new Gyrokinetic Critical Pedestal model was developed, accurately predicting pedestal structure by identifying KBMs as the primary stability limit, offering a critical constraint for future high-confinement scenarios. To address the challenge of high heat flux, novel liquid lithium plasma-facing components were modeled. The analysis confirmed that lithium vapor shielding is a self-regulating mechanism for heat mitigation, while also emphasizing that strong main ion parallel flow is essential to minimize core lithium contamination. Finally, progress toward steady-state operation was anchored by developing the required physics basis and control tools. This includes predictive modeling for Reversed Magnetic Shear sustainment, demonstrating that magnetic island-induced bootstrap current reduction is negligible in STs, and advancing real-time control and disruption avoidance capabilities. The development of high-speed surrogate models (e.g., MMMNet) provides computationally efficient tools vital for non-inductive scenario optimization and integrated, low-disruptivity operations planned for NSTX-U.
- 15 January 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (3)
Top Cited PapersOpen AccessSpherical tokamak physics research in preparation for the operation of NSTX-U
The National Spherical Torus Experiment Upgrade (NSTX-U) is preparing to resume operation, representing a crucial step toward realizing compact, cost-effective fusion pilot plants (FPPs). In advance of this, extensive modeling and data analysis have been conducted to advance the physics basis for low-aspect-ratio, high-performance plasma regimes, focusing on three core objectives: confinement and stability, power and particle handling, and steady-state operation. Significant progress has been made in understanding the electron temperature flattening in high-β plasmas, which is shown to be driven by a complex interplay of MHD instabilities (e.g., non-resonant infernal modes), fast-ion-driven Alfvén eigenmodes, and electron and ion-scale micro-instabilities, particularly Kinetic Ballooning Modes (KBMs), whose destabilization is strongly dependent on parallel magnetic field fluctuations (δB ‖ ). Furthermore, a new Gyrokinetic Critical Pedestal model was developed, accurately predicting pedestal structure by identifying KBMs as the primary stability limit, offering a critical constraint for future high-confinement scenarios. To address the challenge of high heat flux, novel liquid lithium plasma-facing components were modeled. The analysis confirmed that lithium vapor shielding is a self-regulating mechanism for heat mitigation, while also emphasizing that strong main ion parallel flow is essential to minimize core lithium contamination. Finally, progress toward steady-state operation was anchored by developing the required physics basis and control tools. This includes predictive modeling for Reversed Magnetic Shear sustainment, demonstrating that magnetic island-induced bootstrap current reduction is negligible in STs, and advancing real-time control and disruption avoidance capabilities. The development of high-speed surrogate models (e.g., MMMNet) provides computationally efficient tools vital for non-inductive scenario optimization and integrated, low-disruptivity operations planned for NSTX-U.
- Open Access
- 26 November 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (11) , 115031
Experimental progress and future plans on spherical tokamak, QUEST
QUEST (Q-shu university experiment with steady state spherical tokamak) aims at effective plasma current start-up and stable maintenance of plasma discharge. To solve the inherent problems in a spherical tokamak (ST) arising from insufficient space for placing the inductive center solenoid, electron cyclotron current drive (ECCD) and transient coaxial helicity injection (T-CHI) are implemented as a non-inductive plasma start-up method in QUEST. Efficient ECCD assisted by energetic electrons could be achieved. By combining control of the wave injection angle and application of a negative toroidal electric field, the bulk electron temperature could be raised up to 1 keV due to selective wave power absorption in the bulk electrons. The plasma current of over 50 kA contained within the closed flux surface could be obtained with a floating single biased electrode placed on lower divertor plates for T-CHI. Long-pulse operations on QUEST are impeded frequently due to wall saturation and subsequent density runaway caused by fuel particle imbalance. Since 2014, a unique tool called the ‘hot wall’ has been implemented to overcome the imbalance. The hot wall has a capability to regulate its surface temperature using a heater and two water cooling channels. With the help of the hot wall, 6 h discharges were obtained in 2020. Cooling down of the surface of the hot wall was significantly effective in recovering the wall pumping and was useful to extend the pulse duration. Augmentation of the toroidal magnetic field, B T up to 0.5 T from 0.25 T and a continuous wave (CW) gyrotron of 28 GHz are planned for QUEST in the near future. As raising B T provides a fundamental resonance of electron cyclotron waves (ECWs) with 28 GHz, more effective plasma current start-up and heating will be performed. Long-pulse operations with higher plasma parameters are expected.
- 26 November 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (11) , 115031
Open AccessExperimental progress and future plans on spherical tokamak, QUEST
QUEST (Q-shu university experiment with steady state spherical tokamak) aims at effective plasma current start-up and stable maintenance of plasma discharge. To solve the inherent problems in a spherical tokamak (ST) arising from insufficient space for placing the inductive center solenoid, electron cyclotron current drive (ECCD) and transient coaxial helicity injection (T-CHI) are implemented as a non-inductive plasma start-up method in QUEST. Efficient ECCD assisted by energetic electrons could be achieved. By combining control of the wave injection angle and application of a negative toroidal electric field, the bulk electron temperature could be raised up to 1 keV due to selective wave power absorption in the bulk electrons. The plasma current of over 50 kA contained within the closed flux surface could be obtained with a floating single biased electrode placed on lower divertor plates for T-CHI. Long-pulse operations on QUEST are impeded frequently due to wall saturation and subsequent density runaway caused by fuel particle imbalance. Since 2014, a unique tool called the ‘hot wall’ has been implemented to overcome the imbalance. The hot wall has a capability to regulate its surface temperature using a heater and two water cooling channels. With the help of the hot wall, 6 h discharges were obtained in 2020. Cooling down of the surface of the hot wall was significantly effective in recovering the wall pumping and was useful to extend the pulse duration. Augmentation of the toroidal magnetic field, B T up to 0.5 T from 0.25 T and a continuous wave (CW) gyrotron of 28 GHz are planned for QUEST in the near future. As raising B T provides a fundamental resonance of electron cyclotron waves (ECWs) with 28 GHz, more effective plasma current start-up and heating will be performed. Long-pulse operations with higher plasma parameters are expected.
- 6 October 2025
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 44 (2) , 1-9
Active Divertor Heat Flux Control using Impurity Powder Dropper
- 6 October 2025
- Published by Springer Nature in Journal of Fusion Energy
- Vol. 44 (2) , 1-9
Active Divertor Heat Flux Control using Impurity Powder Dropper
- Open Access
- 4 September 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (9) , 095007
Design considerations for optimizing the transient CHI injector on QUEST
Transient coaxial helicity injection (transient CHI) on the QUEST (Q-shu University Experiment with Steady-State ST) spherical tokamak (ST) has recently validated the floating biased electrode configuration for solenoid-free plasma startup. In support of a significant divertor upgrade on QUEST, the details of the transient CHI injector geometry on QUEST have been examined more closely using tokamak simulation code (TSC) simulations. QUEST uses a HIT-II-like (Helicity Injected Torus) injector configuration in which the injector region is comprised of coaxial injector electrodes located in the lower part of the machine. TSC simulations indicate high injector flux operation may benefit from an increased gap between the coaxial electrodes. This is the first study to examine the differences between an open and closed electrode configuration for solenoid-free plasma startup using transient CHI. Results show that both configurations can generate similar levels of closed flux, but the closed configuration may be easier to implement in some ST designs as a much smaller portion of the injector needs to be close to the injector flux coil. Results show that increasing the electrode gap width from the present 10.8 cm to about 15–20 cm would increase the closed flux fraction by about 40%. The results presented in this paper are generally applicable to the CHI design for other STs.
- 4 September 2025
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (9) , 095007
Open AccessDesign considerations for optimizing the transient CHI injector on QUEST
Transient coaxial helicity injection (transient CHI) on the QUEST (Q-shu University Experiment with Steady-State ST) spherical tokamak (ST) has recently validated the floating biased electrode configuration for solenoid-free plasma startup. In support of a significant divertor upgrade on QUEST, the details of the transient CHI injector geometry on QUEST have been examined more closely using tokamak simulation code (TSC) simulations. QUEST uses a HIT-II-like (Helicity Injected Torus) injector configuration in which the injector region is comprised of coaxial injector electrodes located in the lower part of the machine. TSC simulations indicate high injector flux operation may benefit from an increased gap between the coaxial electrodes. This is the first study to examine the differences between an open and closed electrode configuration for solenoid-free plasma startup using transient CHI. Results show that both configurations can generate similar levels of closed flux, but the closed configuration may be easier to implement in some ST designs as a much smaller portion of the injector needs to be close to the injector flux coil. Results show that increasing the electrode gap width from the present 10.8 cm to about 15–20 cm would increase the closed flux fraction by about 40%. The results presented in this paper are generally applicable to the CHI design for other STs.
- Open Access
- 1 April 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (4)
Experimental demonstration of transient CHI start-up using a floating biased electrode configuration
Transient coaxial helicity injection (CHI) current start-up in a spherical tokamak (ST) has been demonstrated for the first time using a reactor-relevant floating single biased (FSB) electrode configuration on QUEST. Unlike previous applications of CHI on HIT-II and on NSTX in which the entire ST vessel was split in two using two toroidal ceramic rings as vacuum breaks, in the FSB electrode configuration on QUEST, only the lower outer divertor plate is electrically insulated from the rest of the vessel. This is the CHI injector region. A CHI discharge is generated by driving current, using an external power supply, along magnetic field lines that connect the inner and outer divertor plates in the CHI injector region. The CHI plasma evolution and closed flux formation on QUEST are very similar to those on NSTX and have generated toroidal currents of 150 kA with 100 kA of current flowing on closed flux surfaces. An alternate, force-free model approach has been used to derive the CHI scaling relations. The resulting CHI scaling relations from the model are consistent with the conventional CHI scaling relations, which state that the CHI generated toroidal current is proportional to the CHI injector flux and the CHI injector current is inversely proportional to the toroidal field. These results from QUEST bode well for the application of CHI in a new generation of compact high field STs and low aspect ratio tokamaks in which the space for the central solenoid is very restricted.
- 1 April 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (4)
Open AccessExperimental demonstration of transient CHI start-up using a floating biased electrode configuration
Transient coaxial helicity injection (CHI) current start-up in a spherical tokamak (ST) has been demonstrated for the first time using a reactor-relevant floating single biased (FSB) electrode configuration on QUEST. Unlike previous applications of CHI on HIT-II and on NSTX in which the entire ST vessel was split in two using two toroidal ceramic rings as vacuum breaks, in the FSB electrode configuration on QUEST, only the lower outer divertor plate is electrically insulated from the rest of the vessel. This is the CHI injector region. A CHI discharge is generated by driving current, using an external power supply, along magnetic field lines that connect the inner and outer divertor plates in the CHI injector region. The CHI plasma evolution and closed flux formation on QUEST are very similar to those on NSTX and have generated toroidal currents of 150 kA with 100 kA of current flowing on closed flux surfaces. An alternate, force-free model approach has been used to derive the CHI scaling relations. The resulting CHI scaling relations from the model are consistent with the conventional CHI scaling relations, which state that the CHI generated toroidal current is proportional to the CHI injector flux and the CHI injector current is inversely proportional to the toroidal field. These results from QUEST bode well for the application of CHI in a new generation of compact high field STs and low aspect ratio tokamaks in which the space for the central solenoid is very restricted.
- 29 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 3449-3454
Design of the Electromagnetic Particle Injector (EPI) for Tokamak Deployment
Both predicting and controlling disruptions are critical and urgent issues for ITER as some disruptions with a short warning time may be unavoidable. For these cases, a rapid response disruption mitigation system (DMS) referred to as the electromagnetic particle injector (EPI) is being developed. The primary advantages of the EPI are its fast response time and high velocity, which have been demonstrated in offline experiments (Raman et al., 2021). The EPI is capable of accelerating a metallic sabot electromagnetically using a rail gun to the required velocities ( $>$ 2 km/s) within 2 ms. Two high-field racetrack magnets able to generate fields over 2 T are positioned above and below the rails to permit high velocity at low rail currents, a requirement to minimize electrode erosion. At the end of the acceleration phase, a sabot capture mechanism retains the spent sabot inside the vacuum chamber that houses the EPI. At this point, it releases well-defined microspheres, or a shell pellet, of a radiative payload into the disrupting plasma. A remotely operated sabot loading system positioned behind the injector contains several pre-equipped sabots that can be loaded by an operator from the tokamak control room. The injector is interfaced to the tokamak through a guide tube attached to the front of the EPI vacuum chamber. The advantages of the EPI system over other DMSs under consideration are described in conjunction with the details of an EPI system designed for near-term test on an existing large tokamak.
- 29 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 3449-3454
Design of the Electromagnetic Particle Injector (EPI) for Tokamak Deployment
Both predicting and controlling disruptions are critical and urgent issues for ITER as some disruptions with a short warning time may be unavoidable. For these cases, a rapid response disruption mitigation system (DMS) referred to as the electromagnetic particle injector (EPI) is being developed. The primary advantages of the EPI are its fast response time and high velocity, which have been demonstrated in offline experiments (Raman et al., 2021). The EPI is capable of accelerating a metallic sabot electromagnetically using a rail gun to the required velocities ( $>$ 2 km/s) within 2 ms. Two high-field racetrack magnets able to generate fields over 2 T are positioned above and below the rails to permit high velocity at low rail currents, a requirement to minimize electrode erosion. At the end of the acceleration phase, a sabot capture mechanism retains the spent sabot inside the vacuum chamber that houses the EPI. At this point, it releases well-defined microspheres, or a shell pellet, of a radiative payload into the disrupting plasma. A remotely operated sabot loading system positioned behind the injector contains several pre-equipped sabots that can be loaded by an operator from the tokamak control room. The injector is interfaced to the tokamak through a guide tube attached to the front of the EPI vacuum chamber. The advantages of the EPI system over other DMSs under consideration are described in conjunction with the details of an EPI system designed for near-term test on an existing large tokamak.
- Open Access
- 17 November 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (1) , 014002
Demonstration of transient CHI startup using a floating biased electrode configuration
Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.
- 17 November 2023
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (1) , 014002
Open AccessDemonstration of transient CHI startup using a floating biased electrode configuration
Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 3429-3434
Design Considerations for a Transient CHI Gas Injection System for Pegasus-III
Due to restricted space for a full-sized solenoid, compact tokamaks and spherical tokamaks such as the ST40 and the next-step ST80 device planned by Tokamak Energy, Oxfordshire, U.K., could considerably benefit from solenoid-less plasma startup capability. Transient coaxial helicity injection (CHI), a method first developed on the small helicity injected torus-II (HIT-II) experiment and then validated on national spherical torus experiment (NSTX), is a method to initiate an inductive-like tokamak plasma discharge without reliance on the central solenoid. In both these devices, toroidal ceramic insulators were used to electrically separate the inner and outer vessel components so that the magnetic flux that initially connects the inner and outer vessel components could be grown into the vessel using J $\times$ B forces to generate a closed magnetic field line configuration. In reactors, the installation of large toroidal insulators as part of the vacuum vessel boundary may not be feasible. To address this design requirement, a first of its kind, floating double-biased reactor-relevant CHI configuration is being developed for Pegasus-III. A particularly challenging requirement for a successful transient CHI discharge generation is the need to reduce the amount of fuel gas injected to the levels normally used for discharge initiation using the inductive solenoid. While higher levels of gas injection ease the plasma breakdown requirements, it also favors discharge initiation outside the CHI injector region. This stringent requirement generally requires that a small gas plenum be located close to an appropriately designed gas injection manifold in the injector region in a high gas conductance configuration. Plasma startup using transient CHI and the design aspects for a transient CHI gas injection system for the Pegasus-III geometry are described.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (9) , 3429-3434
Design Considerations for a Transient CHI Gas Injection System for Pegasus-III
Due to restricted space for a full-sized solenoid, compact tokamaks and spherical tokamaks such as the ST40 and the next-step ST80 device planned by Tokamak Energy, Oxfordshire, U.K., could considerably benefit from solenoid-less plasma startup capability. Transient coaxial helicity injection (CHI), a method first developed on the small helicity injected torus-II (HIT-II) experiment and then validated on national spherical torus experiment (NSTX), is a method to initiate an inductive-like tokamak plasma discharge without reliance on the central solenoid. In both these devices, toroidal ceramic insulators were used to electrically separate the inner and outer vessel components so that the magnetic flux that initially connects the inner and outer vessel components could be grown into the vessel using J $\times$ B forces to generate a closed magnetic field line configuration. In reactors, the installation of large toroidal insulators as part of the vacuum vessel boundary may not be feasible. To address this design requirement, a first of its kind, floating double-biased reactor-relevant CHI configuration is being developed for Pegasus-III. A particularly challenging requirement for a successful transient CHI discharge generation is the need to reduce the amount of fuel gas injected to the levels normally used for discharge initiation using the inductive solenoid. While higher levels of gas injection ease the plasma breakdown requirements, it also favors discharge initiation outside the CHI injector region. This stringent requirement generally requires that a small gas plenum be located close to an appropriately designed gas injection manifold in the injector region in a high gas conductance configuration. Plasma startup using transient CHI and the design aspects for a transient CHI gas injection system for the Pegasus-III geometry are described.