Phillip Y. Foeller
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Phillip Y. Foeller has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ian Michael Reaney
Department of Materials Science and Engineering, University of Sheffield, Mappin Street, Sheffield S1 3JD, U.K.
3 shared publications D. C. Sinclair
University of Sheffield Functional Materials and Devices Group, Department of Materials Science and Engineering Sheffield S1 3JD, United Kingdom
2 shared publicationsBethany K. Russell
Department of Chemistry, The University of York, York, UK
1 shared publicationDerek C. Sinclair
Department of Materials Science and Engineering, University of Sheffield , Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD, United Kingdom
1 shared publicationEdward J. Davis
Department of Chemistry, The University of York, York, UK
1 shared publicationJ. S. Dean
University of Sheffield Functional Materials and Devices Group, Department of Materials Science and Engineering Sheffield S1 3JD, United Kingdom
1 shared publication
Latest Publications
- 15 December 2016
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 56 (1) , 542-547
Synthesis of Barium Titanate Using Deep Eutectic Solvents
Novel synthetic routes to prepare functional oxides at lower temperatures are an increasingly important area of research. Many of these synthetic routes, however, use water as the solvent and rely on dissolution of the precursors, precluding their use with, for example, titanates. Here we present a low-cost solvent system as a means to rapidly create phase-pure ferroelectric barium titanate using a choline chloride-malonic acid deep eutectic solvent. This solvent is compatible with alkoxide precursors and allows for the rapid synthesis of nanoscale barium titanate powders at 950 °C. The phase and morphology were determined, along with investigation of the synthetic pathway, with the reaction proceeding via BaCl2 and TiO2 intermediates. The powders were also used to create sintered ceramics, which exhibit a permittivity maximum corresponding to a tetragonal-cubic transition at 112 °C, as opposed to the more conventional temperature of ∼120 °C. The lower-than-expected value for the ferro- to para-electric phase transition is likely due to undetectable levels of contaminants.
- 15 December 2016
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 56 (1) , 542-547
Synthesis of Barium Titanate Using Deep Eutectic Solvents
Novel synthetic routes to prepare functional oxides at lower temperatures are an increasingly important area of research. Many of these synthetic routes, however, use water as the solvent and rely on dissolution of the precursors, precluding their use with, for example, titanates. Here we present a low-cost solvent system as a means to rapidly create phase-pure ferroelectric barium titanate using a choline chloride-malonic acid deep eutectic solvent. This solvent is compatible with alkoxide precursors and allows for the rapid synthesis of nanoscale barium titanate powders at 950 °C. The phase and morphology were determined, along with investigation of the synthetic pathway, with the reaction proceeding via BaCl2 and TiO2 intermediates. The powders were also used to create sintered ceramics, which exhibit a permittivity maximum corresponding to a tetragonal-cubic transition at 112 °C, as opposed to the more conventional temperature of ∼120 °C. The lower-than-expected value for the ferro- to para-electric phase transition is likely due to undetectable levels of contaminants.
- Open Access
- 22 August 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (8) , 082904
Design of a bilayer ceramic capacitor with low temperature coefficient of capacitance
We show how a simple bilayer system that combines a layer of undoped BaTiO3 (BT) with a second layer of Ba0.975Na0.025Ti0.975Nb0.025O3 (2.5NNBT) can be used to improve the temperature coefficient of capacitance (TCC) of BaTiO3-based materials for capacitor applications. The bilayer system emulates the volume ratio between a conventional core and shell phase microstructure allowing a simple resource efficient approach to optimise the system for low TCC. Optimisation was achieved with a volume ratio of 0.67 2.5NNBT with 0.33 BT and results in a TCC of ±6% over the temperature range ∼25 to 125 °C whilst maintaining a permittivity of εr ∼ 3000 and low dielectric loss.
- 22 August 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 109 (8) , 082904
Open AccessDesign of a bilayer ceramic capacitor with low temperature coefficient of capacitance
We show how a simple bilayer system that combines a layer of undoped BaTiO3 (BT) with a second layer of Ba0.975Na0.025Ti0.975Nb0.025O3 (2.5NNBT) can be used to improve the temperature coefficient of capacitance (TCC) of BaTiO3-based materials for capacitor applications. The bilayer system emulates the volume ratio between a conventional core and shell phase microstructure allowing a simple resource efficient approach to optimise the system for low TCC. Optimisation was achieved with a volume ratio of 0.67 2.5NNBT with 0.33 BT and results in a TCC of ±6% over the temperature range ∼25 to 125 °C whilst maintaining a permittivity of εr ∼ 3000 and low dielectric loss.
- Open Access
- 14 January 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 4 (18) , 6896-6901
A resource efficient design strategy to optimise the temperature coefficient of capacitance of BaTiO3-based ceramics using finite element modelling
A finite element modelling - experimental approach as a new resource efficient design strategy to improve the temperature stability of BaTiO3 (BT)-based ceramic materials for MLCCs. Illustrated using rare earth-free NaNbO3-doped BT and found to decrease the magnitude of the TCC.
- 14 January 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 4 (18) , 6896-6901
Open AccessA resource efficient design strategy to optimise the temperature coefficient of capacitance of BaTiO3-based ceramics using finite element modelling
A finite element modelling - experimental approach as a new resource efficient design strategy to improve the temperature stability of BaTiO3 (BT)-based ceramic materials for MLCCs. Illustrated using rare earth-free NaNbO3-doped BT and found to decrease the magnitude of the TCC.
- 17 July 2014
- Published by Taylor & Francis in Liquid Crystals
- Vol. 41 (11) , 1635-1646
Liquid-crystalline structure–property relationships in halogen-terminated derivatives of cyanobiphenyl
In this article, we report on the liquid-crystalline properties of two series of halogen-terminated cyanobiphenyl-based materials. Unlike other rod-shaped, halogen-terminated materials reported, these materials do not exhibit the smectic A phase and instead only exhibit nematic liquid-crystal mesomorphism. Comparisons between these materials and analogous unsubstituted materials were made, and the relationships between their molecular structures and phase behaviour are discussed with the aid of molecular modelling at the B3LYP/6-31G* level of density functional theory.
- 17 July 2014
- Published by Taylor & Francis in Liquid Crystals
- Vol. 41 (11) , 1635-1646
Liquid-crystalline structure–property relationships in halogen-terminated derivatives of cyanobiphenyl
In this article, we report on the liquid-crystalline properties of two series of halogen-terminated cyanobiphenyl-based materials. Unlike other rod-shaped, halogen-terminated materials reported, these materials do not exhibit the smectic A phase and instead only exhibit nematic liquid-crystal mesomorphism. Comparisons between these materials and analogous unsubstituted materials were made, and the relationships between their molecular structures and phase behaviour are discussed with the aid of molecular modelling at the B3LYP/6-31G* level of density functional theory.