Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hui Qian has a total of 145 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Review on piezoelectric wind-excited vortex-induced vibration energy harvesting technologies

    by Bin Li, Zhenhua Zhang, Hui Qian, Lei Wang, Zhen Wang, Tong Guo

    In the realm of ambient energy harvesting, wind is widely recognized as one of the most cost-effective renewable resources, supporting the development of distributed wind energy harvesting technologies. Unlike conventional rotary wind turbines, wind-induced vibration energy harvesting (WIVEH) systems feature simpler architectures, greater design flexibility, and superior site adaptability, making them promising supplementary power solutions for low-power electronic applications. However, natural winds in inland and urban environments are typically characterized by low and fluctuating velocities, posing significant challenges to the efficiency and reliability of WIVEH systems. To address these challenges, this article comprehensively reviews recent advances in wind-excited vortex-induced vibration energy harvesting technologies, with particular emphasis on fundamental mechanisms, bluff body optimization, nonlinear dynamics, frequency tuning strategies, and adaptive structural designs. Beyond structural performance enhancement, the scaling characteristics of different energy conversion approaches are discussed, highlighting the advantages of piezoelectric mechanisms for microscale energy harvesting and self-powered sensing applications. The integration of WIVEH systems with wireless sensor networks and smart infrastructure is also reviewed, demonstrating their potential for distributed and autonomous monitoring applications. Current challenges and future development directions are further analyzed, including broadband operation under complex wind conditions, efficient power management, multifunctional materials, and system-level integration. This review provides comprehensive insights into the development of WIVEH technologies from fundamental vibration mechanisms toward practical self-powered sensing platforms.

  • Mix design optimization for 3D ‐printable ECC reinforced with SMA fiber: Evolution of rheology, printability, strain‐hardening, and microstructure

    by Hui Qian, Muhammad Faizan Ali, Muhammad Umar, Zongao Li, Ali Raza, Aneel Manan, Muhammad Ishaq

    Extrusion‐based three‐dimensional concrete printing enables automated construction without formwork, yet its structural application is restricted by the brittle behavior and limited tensile capacity of printable cementitious materials. In particular, reconciling fresh‐state printability with tensile strain‐hardening remains a key challenge for engineered cementitious composites (ECC). This study develops and optimizes a shape memory alloy fiber‐reinforced engineered cementitious composite (SMAF‐ECC) for extrusion‐based 3D printing using an integrated material process performance framework. An orthogonal experimental design was employed to optimize ECC mix proportions by jointly evaluating setting time, fluidity, rheology, extrudability, buildability, and hydration heat evolution. An optimal printable ECC mixture was identified and subsequently reinforced with NiTi SMAF of 26 and 32 mm length at 0.35–1.0 vol%. Results show that a 0.60% attapulgite dosage provides balanced early‐age hydration and rheological build‐up, enabling stable extrusion and high buildability (tan θ ≈0.019) without excessive flow resistance. SMAF incorporation slightly reduces flowability but significantly enhances tensile performance. The optimal SMAF‐ECC (32 mm, 1.0%) achieved peak tensile stresses of 5.72 MPa cast and 5.40 MPa 3D‐printed, representing an improvement of approximately 45% over fiber‐free ECC. Ultimate tensile strain increased to 6.8% and 6.35%, respectively, while preserving stable strain‐hardening behavior after printing. Microstructural and porosity analyses confirmed a dense C–S–H‐dominated matrix, refined pore structure, and predominantly mechanical fiber–matrix interaction. The findings demonstrate that SMAF‐ECC enables high‐ductility, damage‐tolerant, and printable smart cementitious composites, offering a promising solution for advanced structural applications in digital construction.

  • Study on bond-slip behavior at the interface between Fe-SMA and concrete after thermal activation

    by Dongxiang Zhang, Hui Qian, Zekai Su, Jiajie Wang

    This study investigates the residual bond behavior of thermally activated Fe-SMA/concrete interfaces through 39 groups of 117 single-shear specimens, considering adhesive type, adhesive thickness, bond length, heating temperature, thermal cycles, and substrate strength. Results show that high-temperature-resistant epoxy adhesives retained acceptable bond capacity after short-term exposure up to 200°C, and failure in concrete specimens was governed mainly by surface concrete spalling rather than adhesive failure. The interfacial ultimate load increased with adhesive thickness, bond length, and substrate strength, but decreased with increasing adhesive elastic modulus and heating temperature. Within the tested range, a 1 mm adhesive thickness, a low-modulus heat-resistant adhesive, and a 150 mm bond length are recommended for practical use. Among the candidate constitutive models, the Nakaba model best described the test results, and a temperature-dependent parameterization was established for the investigated range.

  • Open Access

    Sxperimental study on a resilient SMA-ECC composite frame under extreme seismic loading

    by Zongao Li, Hui Qian, Liping Kang, Hongyuan Fang, Hong-Nan Li, Cheng Fang

    Conventional reinforced concrete (RC) frames frequently suffer from severe structural damage and unrecoverable residual deformations following major earthquakes, which act as extreme seismic events, rendering post-earthquake repairs difficult and costly. To address this issue and enhance structural resilience under extreme loading, this study proposes a novel self-centering frame utilizing an advanced hybrid composite system comprising superelastic shape memory alloys (SMA) and engineered cementitious composites (ECC). The SMA bars and ECC material are strategically applied in the plastic hinge regions of the beam ends and column bases, replacing conventional steel reinforcement and concrete. To evaluate the seismic performance of the proposed system, two half-scale frame specimens, namely one conventional RC frame and one SMA-ECC frame, were designed, constructed, and tested under pseudo-static cyclic loading. The experimental results indicate that the hybrid SMA-ECC composite frame exhibits a stable "flag-shaped" hysteretic response with minimal pinching effects. Compared to the conventional RC frame, the SMA-ECC composite system demonstrates enhanced damage control, characterized by the multiple micro-cracking behavior of the ECC matrix without cover spalling, alongside excellent self-centering capacity. Specifically, the residual inter-story drift ratio of the SMA-ECC frame is limited to approximately 0.5% even at an extreme peak drift ratio of 5.0%, which is significantly below the post-earthquake reparability threshold. Furthermore, the SMA-ECC frame maintains stable energy dissipation and superior load-bearing stability under large deformations. The findings of this study provide a robust experimental foundation for the application of advanced multi-material composite structures in earthquake-resilient engineering under extreme environments.

  • Open Access

    Experimental study on axial compression performance of concrete columns srengthened with SMA cable grid-reinforced ECC composites

    by Hui Qian, Chenglong Yang, Yifei Shi, Bo Wu, Fei Li

    In this paper, a new type of super-elastic Ni-Ti shape memory alloy stranded wire mesh reinforced engineering cement-based composite material (SMACG-ECC) is proposed. By designing concrete column specimens with different parameters, the effects of stranded wire type, column slenderness ratio, stranded wire diameter, reinforcement spacing, pre-strain level and pre-damage degree on the axial compression performance of SMACG-ECC reinforced concrete columns are systematically studied. A simplified calculation model of compressive bearing capacity of SMACG-ECC reinforced concrete columns is established. The calculated values are in good agreement with the experimental values, and the error is within a reasonable range.The results show that the SMACG-ECC reinforced column presents multi-stage characteristics. There are no cracks in the initial elastic stage, and microcracks appear on the surface of ECC in the damage development stage. The bearing capacity is improved in the strengthening stage, and some SMA strands break after the peak load, but there is still residual bearing capacity. The crack control ability of SCG-ECC reinforced column after peak load is weak. Compared with plain concrete columns, the peak displacement of SMACG-ECC reinforced columns is greatly increased, and the failure mode is transformed into ductile multi-crack cracking, which effectively improves the brittle failure characteristics of concrete columns.The parameter analysis shows that the comprehensive performance is the best when using 2.5mm SMA strand reinforcement. The slenderness ratio has a significant effect on the mechanical properties. The 400 mm short column has high bearing capacity but poor ductility, and the 500-600 mm short column has the best ductility. Reducing the spacing of the strands can increase the peak load (an increase of 12.3%) but limit the deformation capacity ; when the pre-strain level increases to 4%, the peak load increases by 10.5% but the ductility decreases. The degree of pre-damage is negatively correlated with the bearing capacity. The research results provide a theoretical basis for improving the seismic performance of concrete columns.

  • Development of a novel Cu–Al–Mn SMA bolts-based self-centering wedge-shaped friction-viscoelastic composite damper

    by Hui Qian, Wenhao Fan, Yifei Shi, Canxing Qiu

    Conventional structural dampers are constrained by inherent limitations: viscoelastic dampers demonstrate low initial stiffness, reducing their effectiveness under wind loads and minor earthquakes; friction dampers provide considerable energy dissipation but often induce significant residual deformations; and self-centering dampers based on nickel–titanium shape memory alloys (Ni–Ti SMAs) effectively mitigate residual displacements yet are hindered by prohibitively high material costs, which restricts their widespread application. To holistically address these challenges, this study proposes a novel self-centering wedge-shaped friction and viscoelastic composite damper that incorporates cost-effective copper-based SMAs. Initially, the effects of solution treatment temperature and cyclic thermal loading on the mechanical behavior of Cu-based SMA bolts were systematically investigated. Subsequently, the configuration and working principle of the proposed damper were described in detail. Furthermore, quasi–static cyclic tests were conducted to assess its hysteretic behavior, self-centering capability, and energy dissipation characteristics. Finally, a comprehensive numerical investigation was performed to systematically quantify the influence of key parameters—including loading frequency, bolt preload, bolt diameter, wedge surface friction coefficient, and wedge slope height—on the damper’s cycle performance. The experimental and numerical results collectively indicate that bolt preload contributes to the most substantial enhancement in initial stiffness, with an increase of up to 585%. A critical transition in performance is observed at wedge slope heights between 8 mm and 10 mm. Although a higher friction coefficient improves the equivalent viscous damping ratio, it compromises the self-centering capability. Moreover, increased loading frequency enhances energy dissipation but leads to an increase in residual displacements.


  • Uniaxial compression behavior, constitutive modeling, and self-healing capabilities of SMA-reinforced engineered cementitious composites

    by Muhammad Umar, Hui Qian, Muhammad Faizan Ali, Syed Basit Ali, Muhammad Saeed Zafar, Yasser Alashker


  • Open Access

    Cyclic Behavior of a Novel Self‐Centering Rotational Wedge–Shaped Friction Damper for Prefabricated RC Structure Joints

    by Yifei Shi, Yuan Yao, Hui Qian, Cheng Fang, Liangmin Yu

    A novel self‐centering (SC) rotational wedge–shaped friction damper (SRWFD), which can be used as the high‐performance connector for the joints of beam–column, column–foundation, and coupling beam–shear wall, was proposed and investigated in this study. The friction–self‐regulating function ensures a positive correlation between the axial compressive stress of the annular friction plates and the overall rotational angle of the damper. This design not only maintains excellent energy‐dissipation (ED) capability but also obviously reduces the additional restoring moment required during the unloading process, which is conducive to improving the SC capacity of the damper and reducing the cost. The structure and working principle of the SRWFD were first illustrated, followed by systematically experimental and numerical investigations to verify the innovative functional design and to reveal the influence of the material and pretightening force (PF) of superelastic SMA bolts, the friction coefficient between friction plates and connecting plates, the friction coefficient between wedge‐shaped protrusions and grooves, the effective diameter of SMA bolts, and the height of wedge‐shaped protrusions on the cyclic rotational behavior of the SRWFD. Results showed that the damper exhibited a symmetric flag‐shaped hysteresis characterized by satisfactory SC capacity and ED capability. Furthermore, when the protrusion slope is relatively small, the SC capacity of the SRWFD exhibits a small variation with increasing slope. However, once the protrusion slope exceeds a critical threshold, the overall rotational angle recovery ratio of the SRWFD rapidly increases from approximately 7.3% to about 97.2%. This phenomenon validates the innovative functional design of the novel SRWFD, which leverages the combined structure of annular hard friction plates, wedge‐shaped protrusions, and superelastic SMA bolts to achieve the friction–self‐regulating function. As a result, the restoring moment required to unload the device to a zero rotational angle is significantly reduced, and only a small critical restoring moment is needed to ensure excellent SC performance.