Piotr Król
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Piotr Król has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Bożena Król
Rzeszów University of Technology
25 shared publications - Kinga Pielichowska
Department of Glass Technology and Amorphous Coatings, Faculty of Materials Science and Ceramics, AGH University of Krakow, Al. Mickiewicza 30, 30-059 Krakow, Poland
12 shared publications - Paweł Chmielarz
Department of Physical Chemistry, Faculty of Chemistry, Rzeszow University of Technology, Al. Powstańców Warszawy 6, 35-959 Rzeszow, Poland
12 shared publications - Łukasz Byczyński
Department of Polymers and Biopolymers, Faculty of Chemistry, Rzeszow University of Technology, Al. Powstańców Warszawy 6, 35-959 Rzeszów, Poland
7 shared publications Barbara Pilch-Pitera
6 shared publications- Bozena Krol
Politechnika Rzeszowska, Wydział Chemiczny, Katedra Technologii Tworzyw Sztucznych, Aleje Powstańców Warszawy 6, 35-959 Rzeszów
4 shared publications
Latest Publications
- Open Access
Influence of a Siloxane-Modified DOPO Derivative on the Properties of Polyurethane Cationomer Coatings
Waterborne polyurethane cationomer coatings modified with 1,3-bis(3(3-(propoxy-2-ol-)-9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide)-3-propyloxy))tetramethyldisiloxane (TMDS–AGE–DOPA) containing phosphorus and silicon atoms were obtained. Their structures were confirmed by Fourier transform infrared (FTIR) spectroscopy. The effect of TMDS–AGE–DOPA on thermal properties, flame retardancy, and surface characteristics (gloss, contact angle, surface free energy), as well as performance properties (hardness, impact resistance), was investigated. A coupled TG-FTIR technique was employed for evolved gas analysis. Thermal stability decreased with the addition of the modifier, while the glass transition temperature increased from −19 to 25 °C. The modifier improved the flame retardancy of the material by shifting the peak temperature of the heat release rate (TPHRR) to lower values. The gloss of the coatings was very high (>90 GU at all angles studied), although it decreased with increasing modifier content. The presence of phosphorus moieties from the modifier enhanced hydrophilicity, raising surface free energy (SFE) from 37.9 to 44.0 mJ/m2. The coatings are soft materials with a Persoz hardness in the range of 0.05–0.32. The modifier increased hardness but reduced impact strength. The obtained cationomers can be applied as environmentally friendly coatings on hydrophilic surfaces such as textiles, glass, or wood.
Open AccessInfluence of a Siloxane-Modified DOPO Derivative on the Properties of Polyurethane Cationomer Coatings
Waterborne polyurethane cationomer coatings modified with 1,3-bis(3(3-(propoxy-2-ol-)-9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide)-3-propyloxy))tetramethyldisiloxane (TMDS–AGE–DOPA) containing phosphorus and silicon atoms were obtained. Their structures were confirmed by Fourier transform infrared (FTIR) spectroscopy. The effect of TMDS–AGE–DOPA on thermal properties, flame retardancy, and surface characteristics (gloss, contact angle, surface free energy), as well as performance properties (hardness, impact resistance), was investigated. A coupled TG-FTIR technique was employed for evolved gas analysis. Thermal stability decreased with the addition of the modifier, while the glass transition temperature increased from −19 to 25 °C. The modifier improved the flame retardancy of the material by shifting the peak temperature of the heat release rate (TPHRR) to lower values. The gloss of the coatings was very high (>90 GU at all angles studied), although it decreased with increasing modifier content. The presence of phosphorus moieties from the modifier enhanced hydrophilicity, raising surface free energy (SFE) from 37.9 to 44.0 mJ/m2. The coatings are soft materials with a Persoz hardness in the range of 0.05–0.32. The modifier increased hardness but reduced impact strength. The obtained cationomers can be applied as environmentally friendly coatings on hydrophilic surfaces such as textiles, glass, or wood.
- Open Access
- 1 January 2022
- Published by Elsevier in Progress in Organic Coatings
- Vol. 162
Hydrophilic and hydrophobic films based on polyurethane cationomers containing TiO2 nanofiller
- 1 January 2022
- Published by Elsevier in Progress in Organic Coatings
- Vol. 162
Open AccessHydrophilic and hydrophobic films based on polyurethane cationomers containing TiO2 nanofiller
- Open Access
- 22 February 2021
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 299 (6) , 1011-1029
Polyurethane cationomers containing fluorinated soft segments with hydrophobic properties
The synthesis of ecological waterborne polyurethane cationomers containing fluorinated polyol (0–20 wt.%) was successfully performed. FTIR and NMR analysis results confirmed the structure of the obtained polyurethane cationomers and incorporation of fluorinated component into the polyurethane chains. Average molar mass and phase structure of the obtained PU thin films were determined based on GPC, FTIR, WAXD and SEM-EDX results. The obtained cationomers have linear structures with clearly visible microphase separation of soft and hard segment domains; the presence of fluorinated polyol changes the strength of hydrogen bonds and in consequence degree of phase separation. The activation energy of glass transition was calculated based on multi-frequency DSC data. It has been shown that the presence of soft fluorinated segments in the cationomer structure strongly influences the hydrophobic, thermal and mechanical properties of the obtained films.
- 22 February 2021
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 299 (6) , 1011-1029
Open AccessPolyurethane cationomers containing fluorinated soft segments with hydrophobic properties
The synthesis of ecological waterborne polyurethane cationomers containing fluorinated polyol (0–20 wt.%) was successfully performed. FTIR and NMR analysis results confirmed the structure of the obtained polyurethane cationomers and incorporation of fluorinated component into the polyurethane chains. Average molar mass and phase structure of the obtained PU thin films were determined based on GPC, FTIR, WAXD and SEM-EDX results. The obtained cationomers have linear structures with clearly visible microphase separation of soft and hard segment domains; the presence of fluorinated polyol changes the strength of hydrogen bonds and in consequence degree of phase separation. The activation energy of glass transition was calculated based on multi-frequency DSC data. It has been shown that the presence of soft fluorinated segments in the cationomer structure strongly influences the hydrophobic, thermal and mechanical properties of the obtained films.
- Open Access
- 28 May 2020
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 298 (8) , 1077-1093
Synthesis and property of polyurethane elastomer for biomedical applications based on nonaromatic isocyanates, polyesters, and ethylene glycol
Polyurethane (PU) elastomers were synthesized by the reaction of HDI or IPDI diisocyanates and poly(ε-caprolactone) (PCL or poly(ethylene adipate) (PA) diols and ethylene glycol as a polymer chain extender. IR, 1H, and 13C NMR spectroscopy and X-ray analysis were used for the structural analysis of the formed films. The molecular weight distribution was examined by GPC chromatography. Based on the measured contact angles, free surface energy parameters were calculated. The obtained results were analyzed for the possible use of these polyurethanes as biomaterials. The most promising in this respect was PU-3, which was synthesized from IPDI and PCL. This was due to its high molecular weight of approximately 90,000, the presence of a crystalline phase, and the relatively high hydrophobicity, with a SEP value below 25 mJ/m2. These films showed a good resistance to hydrolysis during incubation in Baxter physiological saline during 6 weeks. Both Gram-positive (Bacillus sp.) and Gram-negative (Pseudomonas sp.) types of bacterial strains were used to test the biodegradation property. Synthesized PUs are biodegradable and showed moderate or even mild cytotoxicity against human normal fibroblasts (BJ) and immortalized keratinocytes (HaCaT), estimated with direct contact assay. The most biocompatible was PU-3 film, which revealed rather mild reactivity against both cell lines, and the least was PU-2 film, synthesized from HDI and PA (severe toxicity for HaCaTs).
- 28 May 2020
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 298 (8) , 1077-1093
Open AccessSynthesis and property of polyurethane elastomer for biomedical applications based on nonaromatic isocyanates, polyesters, and ethylene glycol
Polyurethane (PU) elastomers were synthesized by the reaction of HDI or IPDI diisocyanates and poly(ε-caprolactone) (PCL or poly(ethylene adipate) (PA) diols and ethylene glycol as a polymer chain extender. IR, 1H, and 13C NMR spectroscopy and X-ray analysis were used for the structural analysis of the formed films. The molecular weight distribution was examined by GPC chromatography. Based on the measured contact angles, free surface energy parameters were calculated. The obtained results were analyzed for the possible use of these polyurethanes as biomaterials. The most promising in this respect was PU-3, which was synthesized from IPDI and PCL. This was due to its high molecular weight of approximately 90,000, the presence of a crystalline phase, and the relatively high hydrophobicity, with a SEP value below 25 mJ/m2. These films showed a good resistance to hydrolysis during incubation in Baxter physiological saline during 6 weeks. Both Gram-positive (Bacillus sp.) and Gram-negative (Pseudomonas sp.) types of bacterial strains were used to test the biodegradation property. Synthesized PUs are biodegradable and showed moderate or even mild cytotoxicity against human normal fibroblasts (BJ) and immortalized keratinocytes (HaCaT), estimated with direct contact assay. The most biocompatible was PU-3 film, which revealed rather mild reactivity against both cell lines, and the least was PU-2 film, synthesized from HDI and PA (severe toxicity for HaCaTs).
- Open Access
- 3 September 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (1) , 73-87
Structures, properties and applications of the polyurethane ionomers
- 3 September 2019
- Published by Springer Nature in Journal of Materials Science
- Vol. 55 (1) , 73-87
Open AccessStructures, properties and applications of the polyurethane ionomers
- 1 May 2019
- Published by Elsevier in Progress in Organic Coatings
- Vol. 130, 83-92
Polyurethane cationomer films as ecological membranes for building industry
- 1 May 2019
- Published by Elsevier in Progress in Organic Coatings
- Vol. 130, 83-92
Polyurethane cationomer films as ecological membranes for building industry
- 1 December 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 93, 483-494
Study of chemical, physico-mechanical and biological properties of 4,4′-methylenebis(cyclohexyl isocyanate)-based polyurethane films
- 1 December 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 93, 483-494
Study of chemical, physico-mechanical and biological properties of 4,4′-methylenebis(cyclohexyl isocyanate)-based polyurethane films
- 27 December 2017
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 29 (3) , 1056-1067
Physicochemical and antibacterial properties of polyurethane coatings modified by ZnO
The synthesis of polyurethane nanocomposite coatings containing 1% to 5% suitably dispersed ZnO by 1‐stage polyaddition process in the bulk using 4,4′‐methylenebis(cyclohexyl isocyanate), poly(ε‐caprolactone)diol, and 1,4‐butanediol was performed. Infrared and nuclear magnetic resonance spectra confirmed the structure of obtained polyurethanes. Scanning electron microscope and energy dispersive X‐ray analyzer methods showed randomly distributed ZnO in a polyurethane matrix. The differential scanning calorimetry and wide‐angle X‐ray diffraction patterns were used for the microstructural assessment of the obtained materials. Antimicrobial properties of ZnO and the effect of this modifier on the hydrophobicity of the coatings were demonstrated. The obtained coatings were characterized in terms of the mechanical properties and changes during incubation in a Baxter saline solution.
- 27 December 2017
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 29 (3) , 1056-1067
Physicochemical and antibacterial properties of polyurethane coatings modified by ZnO
The synthesis of polyurethane nanocomposite coatings containing 1% to 5% suitably dispersed ZnO by 1‐stage polyaddition process in the bulk using 4,4′‐methylenebis(cyclohexyl isocyanate), poly(ε‐caprolactone)diol, and 1,4‐butanediol was performed. Infrared and nuclear magnetic resonance spectra confirmed the structure of obtained polyurethanes. Scanning electron microscope and energy dispersive X‐ray analyzer methods showed randomly distributed ZnO in a polyurethane matrix. The differential scanning calorimetry and wide‐angle X‐ray diffraction patterns were used for the microstructural assessment of the obtained materials. Antimicrobial properties of ZnO and the effect of this modifier on the hydrophobicity of the coatings were demonstrated. The obtained coatings were characterized in terms of the mechanical properties and changes during incubation in a Baxter saline solution.
- 10 October 2017
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 295 (12) , 1-13
Methods of increasing hydrophobicity of polyurethane materials: important applications of coatings with low surface free energy
- 10 October 2017
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 295 (12) , 1-13
Methods of increasing hydrophobicity of polyurethane materials: important applications of coatings with low surface free energy
- 2 February 2017
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 28 (11) , 1366-1374
Polyurethane cationomers modified by polysiloxane
The synthesis of waterborne polyurethane cationomers was successfully carried out. Different proportions of α,ω‐di(hydroxyl)polydimethylsiloxane (PDMS) modifier (0–7.3% by weight) were applied. Analysis of IR spectra confirmed the structure of obtained polyurethane cationomers and the incorporation of a modifier into the polyurethane structure. The differential scanning calorimetry (DSC) method was employed for the microstructural assessment of the obtained materials. A clear decrease of the degradation temperature with increasing amounts of incorporated PDMS indicates immiscibility part of the polysiloxane segments with soft segments derived from polyethylene glycol. Changes were discussed in the free surface energy and its components, as calculated independently according to the method suggested by Owens–Wendt, in relation to chemical and physical structures of cationomers as well as morphology of coating surfaces obtained from those cationomers. Test results of contact angle measurements indicated that with increasing content of the polysiloxane in the analyzed films, the contact angles increase. Copyright © 2017 John Wiley & Sons, Ltd.
- 2 February 2017
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 28 (11) , 1366-1374
Polyurethane cationomers modified by polysiloxane
The synthesis of waterborne polyurethane cationomers was successfully carried out. Different proportions of α,ω‐di(hydroxyl)polydimethylsiloxane (PDMS) modifier (0–7.3% by weight) were applied. Analysis of IR spectra confirmed the structure of obtained polyurethane cationomers and the incorporation of a modifier into the polyurethane structure. The differential scanning calorimetry (DSC) method was employed for the microstructural assessment of the obtained materials. A clear decrease of the degradation temperature with increasing amounts of incorporated PDMS indicates immiscibility part of the polysiloxane segments with soft segments derived from polyethylene glycol. Changes were discussed in the free surface energy and its components, as calculated independently according to the method suggested by Owens–Wendt, in relation to chemical and physical structures of cationomers as well as morphology of coating surfaces obtained from those cationomers. Test results of contact angle measurements indicated that with increasing content of the polysiloxane in the analyzed films, the contact angles increase. Copyright © 2017 John Wiley & Sons, Ltd.