Yang-Xiao Qi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yang-Xiao Qi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Jian-Ying Li
School of Electronics and Information, Northwestern Polytechnical University (NWPU), Xian, Shaanxi, China
7 shared publications - Dong Li
National Key Laboratory of Science and Technology on Space Microwave, Xian, China
2 shared publications - Rui Xu
School of Electrical and Electronic Engineering, Nanyang Technological University, Jurong West, Singapore
2 shared publications - Shi-Gang Zhou
Northwestern Polytechnical University
2 shared publications - Guangwei Yang
School of Electronics and Information, Northwestern Polytechnical University, Xian, China
1 shared publication J.-Y. Li
Northwestern Polytechnical University, Xi’an, China
1 shared publication
Latest Publications
- 21 April 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 64 (7) , 1229-1234
A broadband circularly polarized e‐shaped patch antenna
We proposed a broadband e‐shaped circularly polarized (CP) patch antenna with single‐point feed, and the feed point is located at the center of the antenna. The structure of this new antenna includes a ground plate and an e‐shaped patch placed on a substrate. The measured impedance bandwidth of the proposed antenna is approximately 17.89% (3.47–4.15 GHz), and the measured 3‐dB axial ratio bandwidth (ARBW) is about 9.47% (3.63–3.99 GHz). The antenna can achieve the gain of 8.4 to 8.7 dBi within the ARBW. And at the center frequency (3.8 GHz), right‐hand CP to left‐hand CP isolation of the antenna can reach −33 dB.
- 21 April 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 64 (7) , 1229-1234
A broadband circularly polarized e‐shaped patch antenna
We proposed a broadband e‐shaped circularly polarized (CP) patch antenna with single‐point feed, and the feed point is located at the center of the antenna. The structure of this new antenna includes a ground plate and an e‐shaped patch placed on a substrate. The measured impedance bandwidth of the proposed antenna is approximately 17.89% (3.47–4.15 GHz), and the measured 3‐dB axial ratio bandwidth (ARBW) is about 9.47% (3.63–3.99 GHz). The antenna can achieve the gain of 8.4 to 8.7 dBi within the ARBW. And at the center frequency (3.8 GHz), right‐hand CP to left‐hand CP isolation of the antenna can reach −33 dB.
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (2) , 366-370
A Broadband Wide-Angle Scanning Linear Array Antenna With Suppressed Mutual Coupling for 5G Sub-6G Applications
A broadband wide-angle scanning array antenna with suppressed mutual coupling for 5G Sub-6G mobile communication applications is presented in this letter. To reduce mutual coupling, the metal columns are used in the dipole array antenna. The metal columns are positioned below the edge of the dipole, leading to the improved the impedance matching characteristics and a wider scanning angle. A 18 prototype of the suggested design has been manufactured and tested to ensure its usefulness. The overall dimension is 2.3300.2800.240 (0 is the free space wavelength at 2.5 GHz). The measured and simulated results are quite consistent. The main lobe achieves a scanning range of 60 at 2.5-4.5 GHz (57.1%, active VSWR<2) and yields a scanning range of 75 at 3-4 GHz (28.6%, active VSWR<2) with a gain loss of less than 2.5 dB. In the meantime, the side lobe levels (SLLs) are mostly less than or equal to -7.9 dB and the isolation between the antenna elements can yield a maximal additional 14.7 dB enhancement.
- 1 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (2) , 366-370
A Broadband Wide-Angle Scanning Linear Array Antenna With Suppressed Mutual Coupling for 5G Sub-6G Applications
A broadband wide-angle scanning array antenna with suppressed mutual coupling for 5G Sub-6G mobile communication applications is presented in this letter. To reduce mutual coupling, the metal columns are used in the dipole array antenna. The metal columns are positioned below the edge of the dipole, leading to the improved the impedance matching characteristics and a wider scanning angle. A 18 prototype of the suggested design has been manufactured and tested to ensure its usefulness. The overall dimension is 2.3300.2800.240 (0 is the free space wavelength at 2.5 GHz). The measured and simulated results are quite consistent. The main lobe achieves a scanning range of 60 at 2.5-4.5 GHz (57.1%, active VSWR<2) and yields a scanning range of 75 at 3-4 GHz (28.6%, active VSWR<2) with a gain loss of less than 2.5 dB. In the meantime, the side lobe levels (SLLs) are mostly less than or equal to -7.9 dB and the isolation between the antenna elements can yield a maximal additional 14.7 dB enhancement.
- 24 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (5) , 3005-3009
Difference Pattern Synthesis Based on Superposition Principle
The generation process of difference beam is analyzed from the perspective of beam superposition. By analyzing the continuous linear source, a differential beam synthesis method, which can control the side-lobes level, is proposed with a simple form. The side-lobes level of the difference pattern is determined by controlling the direction of the sub-beam and applying the traditional synthesis method, such as Chebyshev method and Taylor method. The proposed synthesis method is theoretical and explicit. Examples are presented for assessing the capabilities of the synthesis of difference patterns. The general distribution function is given.
- 24 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (5) , 3005-3009
Difference Pattern Synthesis Based on Superposition Principle
The generation process of difference beam is analyzed from the perspective of beam superposition. By analyzing the continuous linear source, a differential beam synthesis method, which can control the side-lobes level, is proposed with a simple form. The side-lobes level of the difference pattern is determined by controlling the direction of the sub-beam and applying the traditional synthesis method, such as Chebyshev method and Taylor method. The proposed synthesis method is theoretical and explicit. Examples are presented for assessing the capabilities of the synthesis of difference patterns. The general distribution function is given.
- 29 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (7) , 1276-1280
AMC-Loaded Low-Profile Circularly Polarized Reconfigurable Antenna Array
In this letter, a low-profile circularly polarized (CP) reconfigurable printed antenna array employing switching circuits are reported. To realize low-profile design, an artificial magnetic conductor (AMC) reflector is adopted and loaded at the bottom of the antenna element. Furthermore, in order to meet the high gain and wide bandwidth requirements of S-band satellite communication systems, a 2x4 antenna array is also designed. The proposed antenna array has advantages in three aspects: small size with low profile, polarization diversity and high radiation efficiency. With this method, this antenna array is simulated, fabricated, and tested with reasonable agreement between measurement and simulation.
- 29 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 19 (7) , 1276-1280
AMC-Loaded Low-Profile Circularly Polarized Reconfigurable Antenna Array
In this letter, a low-profile circularly polarized (CP) reconfigurable printed antenna array employing switching circuits are reported. To realize low-profile design, an artificial magnetic conductor (AMC) reflector is adopted and loaded at the bottom of the antenna element. Furthermore, in order to meet the high gain and wide bandwidth requirements of S-band satellite communication systems, a 2x4 antenna array is also designed. The proposed antenna array has advantages in three aspects: small size with low profile, polarization diversity and high radiation efficiency. With this method, this antenna array is simulated, fabricated, and tested with reasonable agreement between measurement and simulation.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 66 (12) , 6950-6957
Superposition Synthesis Method for 2-D Shaped-Beam Array Antenna
In this paper, a synthesis method for shaped beam pattern of two-dimensional array antenna is proposed. The method is based on the array scanning principle and the superposition principle. The method can limit the ripple of main beam by adjusting the sampling point interval and can easily achieve low sidelobe level. Compared to the stochastic optimization methods, this method has obvious time advantage when it is used to synthesize large array antenna. The factors that affect the sidelobe level, ripple and Dynamic Range Ratio is discussed. Sparse array is used to reduce Dynamic Range Ratio.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 66 (12) , 6950-6957
Superposition Synthesis Method for 2-D Shaped-Beam Array Antenna
In this paper, a synthesis method for shaped beam pattern of two-dimensional array antenna is proposed. The method is based on the array scanning principle and the superposition principle. The method can limit the ripple of main beam by adjusting the sampling point interval and can easily achieve low sidelobe level. Compared to the stochastic optimization methods, this method has obvious time advantage when it is used to synthesize large array antenna. The factors that affect the sidelobe level, ripple and Dynamic Range Ratio is discussed. Sparse array is used to reduce Dynamic Range Ratio.
- 19 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 65 (11) , 6157-6160
Shaped Beam Synthesis Based on Superposition Principle and Taylor Method
A technique for the synthesis of shaped beam radiation patterns is proposed. The new synthesis method is based on superposition principle and Taylor method. The method may control the sidelobe level of the shaped beam. The approach includes four steps: 1) get the distribution of pencil beam array with low sidelobe by Taylor method; 2) let the beams scan as a phased array to the specific angles according to the requirement of the shaped beam, The sum pattern is close to the shaping beam; 3) determine the value of angles and weights; and 4) count the distribution of the shaped beam array according to the new array factor function. Numerical results are provided to assess the capabilities of the proposed design method. The method develops an effective approach for the synthesis of shaped beams via uniform linear arrays. Both the ripple and sidelobe level of shaped beam may be controlled by the new synthesis method.
- 19 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 65 (11) , 6157-6160
Shaped Beam Synthesis Based on Superposition Principle and Taylor Method
A technique for the synthesis of shaped beam radiation patterns is proposed. The new synthesis method is based on superposition principle and Taylor method. The method may control the sidelobe level of the shaped beam. The approach includes four steps: 1) get the distribution of pencil beam array with low sidelobe by Taylor method; 2) let the beams scan as a phased array to the specific angles according to the requirement of the shaped beam, The sum pattern is close to the shaping beam; 3) determine the value of angles and weights; and 4) count the distribution of the shaped beam array according to the new array factor function. Numerical results are provided to assess the capabilities of the proposed design method. The method develops an effective approach for the synthesis of shaped beams via uniform linear arrays. Both the ripple and sidelobe level of shaped beam may be controlled by the new synthesis method.
- 29 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 65 (6) , 3217-3220
A Design of U-Shaped Slot Antenna With Broadband Dual Circularly Polarized Radiation
In this communication, a novel broadband dual circularly polarized (CP) antenna is presented. This antenna consists of an U-shaped slot to achieve broadband CP radiation and two 50-Ω microstrip-fed ports to realize both right-hand circular polarization and left-hand circular polarization at the same frequency band. The axial ratio bandwidth (ARBW) is greatly broadened by moving the feeding ports to upper portion of the U-shaped slot. To verify this design, the proposed antenna is fabricated and measured. The measured -10 dB reflection coefficient bandwidth is about 114.4% (1.80-6.61 GHz) and the 3-dB ARBW is approximately 110.5% (1.83-6.35 GHz). The isolation between two ports is better than 14.8 dB within the ARBW.
- 29 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 65 (6) , 3217-3220
A Design of U-Shaped Slot Antenna With Broadband Dual Circularly Polarized Radiation
In this communication, a novel broadband dual circularly polarized (CP) antenna is presented. This antenna consists of an U-shaped slot to achieve broadband CP radiation and two 50-Ω microstrip-fed ports to realize both right-hand circular polarization and left-hand circular polarization at the same frequency band. The axial ratio bandwidth (ARBW) is greatly broadened by moving the feeding ports to upper portion of the U-shaped slot. To verify this design, the proposed antenna is fabricated and measured. The measured -10 dB reflection coefficient bandwidth is about 114.4% (1.80-6.61 GHz) and the 3-dB ARBW is approximately 110.5% (1.83-6.35 GHz). The isolation between two ports is better than 14.8 dB within the ARBW.