Jitendra Solanki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jitendra Solanki has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Bhim Singh
Indian Institute of Technology Delhi
8 shared publications Joachim Bocker
6 shared publicationsNorbert Frohleke
6 shared publicationsPeter Wallmeier
R&D, AEG Power Solutions GmbH Warstein Germany
6 shared publicationsAndreas Averberg
R&D, AEG Power Solutions GmbH Warstein Germany
4 shared publicationsB. Singh
Indian Institute of Technology Delhi
2 shared publications
Latest Publications
- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
22 kW High Efficiency Wide Voltage Range 3-Phase LLC Converter for On-Board-Charger Applications
This paper presents 3- phase LLC as a DC-DC stage topology for 22 kW, 800 V automotive on-board charger. Paper discusses requirements of DC-DC stage of OBC and provides rationale of selection of 3-phase LLC over two parallel 1-phase LLCs. Design of 22 kW 3 -phase LLC is discussed and implementation of the converter using state of the art SiC FETs and SiC diodes is presented. A peak-efficiency of 98.7% is achieved. A very good efficiency of more than 98% is maintained over the wide voltage and power range.
- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
22 kW High Efficiency Wide Voltage Range 3-Phase LLC Converter for On-Board-Charger Applications
This paper presents 3- phase LLC as a DC-DC stage topology for 22 kW, 800 V automotive on-board charger. Paper discusses requirements of DC-DC stage of OBC and provides rationale of selection of 3-phase LLC over two parallel 1-phase LLCs. Design of 22 kW 3 -phase LLC is discussed and implementation of the converter using state of the art SiC FETs and SiC diodes is presented. A peak-efficiency of 98.7% is achieved. A very good efficiency of more than 98% is maintained over the wide voltage and power range.
- Open Access
- 1 June 2015
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 8 (6) , 1068-1080
High‐current variable‐voltage rectifiers: state of the art topologies
Applications such as electrolysis, electrowinning, DC arc furnaces and plasma torches require high‐current (several kA) power supplies at low‐voltage levels (few hundreds of volts). In this study, conventional rectifier topologies (diode‐ and thyristor‐based multi‐pulse rectifiers with on‐load tap changing transformer and chopper‐rectifier) used for high‐current, variable‐voltage applications are reviewed along with recent advancements in the field. The main applications themselves are also discussed. Issues with conventional topologies are highlighted. Power quality techniques like passive and active filters are discussed for power factor and current harmonics compensation. Advanced medium‐ to high‐frequency transformer‐based topologies (with current and voltage source rectifiers) are discussed along with simulation results.
- 1 June 2015
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 8 (6) , 1068-1080
Open AccessHigh‐current variable‐voltage rectifiers: state of the art topologies
Applications such as electrolysis, electrowinning, DC arc furnaces and plasma torches require high‐current (several kA) power supplies at low‐voltage levels (few hundreds of volts). In this study, conventional rectifier topologies (diode‐ and thyristor‐based multi‐pulse rectifiers with on‐load tap changing transformer and chopper‐rectifier) used for high‐current, variable‐voltage applications are reviewed along with recent advancements in the field. The main applications themselves are also discussed. Issues with conventional topologies are highlighted. Power quality techniques like passive and active filters are discussed for power factor and current harmonics compensation. Advanced medium‐ to high‐frequency transformer‐based topologies (with current and voltage source rectifiers) are discussed along with simulation results.
- 13 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 51 (5) , 3995-4005
Voltage-Sequence-Control-Based High-Current Rectifier System
This paper presents a thyristor-based tap changing transformer and a diode rectifier for variable-voltage high-current dc applications. Back-to-back thyristors are connected in series with the transformer taps on the primary side. Thyristors are phase controlled in a continuous manner to achieve variable ac voltage at the secondary side of the transformer. This leads to a variable voltage at the output of the three-phase diode rectifier connected at the secondary side of the transformer. A passive filter is added at the primary side to achieve power factor improvement over the range of output voltage. This scheme is optimized to determine optimum turns ratio of the transformer and optimum reactive power rating of the passive filter. Design guidelines are presented for various values of power factor along with optimum turns ratios and passive filter rating. A 62.5-kW experimental system with a passive filter of 17.5 kVA (reactive) is developed to verify the system performance. In the end, a comparison of the proposed topology with other state-of-the-art topologies is also presented.
- 13 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 51 (5) , 3995-4005
Voltage-Sequence-Control-Based High-Current Rectifier System
This paper presents a thyristor-based tap changing transformer and a diode rectifier for variable-voltage high-current dc applications. Back-to-back thyristors are connected in series with the transformer taps on the primary side. Thyristors are phase controlled in a continuous manner to achieve variable ac voltage at the secondary side of the transformer. This leads to a variable voltage at the output of the three-phase diode rectifier connected at the secondary side of the transformer. A passive filter is added at the primary side to achieve power factor improvement over the range of output voltage. This scheme is optimized to determine optimum turns ratio of the transformer and optimum reactive power rating of the passive filter. Design guidelines are presented for various values of power factor along with optimum turns ratios and passive filter rating. A 62.5-kW experimental system with a passive filter of 17.5 kVA (reactive) is developed to verify the system performance. In the end, a comparison of the proposed topology with other state-of-the-art topologies is also presented.
- 19 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 62 (8) , 4691-4701
Implementation of Hybrid Filter for 12-Pulse Thyristor Rectifier Supplying High-Current Variable-Voltage DC Load
This paper presents a parallel combination of a shunt-connected passive filter and a distribution static compensator (DSTATCOM) for a 12-pulse thyristor rectifier feeding a high-current variable-voltage electrolyzer load. Since the process requires variation of voltage and current over a wide range, the reactive power consumed by the thyristor rectifier also varies enormously. As the passive filter is only able to provide a fixed compensation, the DSTATCOM is used to meet variable reactive power demand to keep the input power factor high even at partial load. In order to keep the DSTATCOM rating small, the bulk of reactive power is supplied by the dominant harmonic passive filter. Moreover, DSTATCOM does not provide any harmonic compensation, which is also taken care by the passive filter. Design and control of this system are discussed briefly, and more emphasis is laid on the implementation of the hybrid filter. An experimental system is tested rigorously, and detailed results are presented.
- 19 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 62 (8) , 4691-4701
Implementation of Hybrid Filter for 12-Pulse Thyristor Rectifier Supplying High-Current Variable-Voltage DC Load
This paper presents a parallel combination of a shunt-connected passive filter and a distribution static compensator (DSTATCOM) for a 12-pulse thyristor rectifier feeding a high-current variable-voltage electrolyzer load. Since the process requires variation of voltage and current over a wide range, the reactive power consumed by the thyristor rectifier also varies enormously. As the passive filter is only able to provide a fixed compensation, the DSTATCOM is used to meet variable reactive power demand to keep the input power factor high even at partial load. In order to keep the DSTATCOM rating small, the bulk of reactive power is supplied by the dominant harmonic passive filter. Moreover, DSTATCOM does not provide any harmonic compensation, which is also taken care by the passive filter. Design and control of this system are discussed briefly, and more emphasis is laid on the implementation of the hybrid filter. An experimental system is tested rigorously, and detailed results are presented.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 1325-1330
Comparison of PWM AC chopper topologies
In this paper, a commonly reported single-phase four-switch AC chopper topology is compared with a six-switch topology in terms of the total harmonic distortion (THD) of the input current, power factor (PF), commutation behavior, robustness and efficiency. Working principles of both topologies are presented along with simulation results. Based on a comparison of the findings, the four-switch topology is found to be better choice for the given application. Thus, the implementation of a four-switch topology is carried out at a power level of 10 kW. Experimental evaluation is carried out in order to verify the suitability of the circuit for the intended application. The experimental setup validates the findings of the simulations. Thus, the proposed approach is a practical way to improve input current THD and PF compared to thyristor choppers.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 1325-1330
Comparison of PWM AC chopper topologies
In this paper, a commonly reported single-phase four-switch AC chopper topology is compared with a six-switch topology in terms of the total harmonic distortion (THD) of the input current, power factor (PF), commutation behavior, robustness and efficiency. Working principles of both topologies are presented along with simulation results. Based on a comparison of the findings, the four-switch topology is found to be better choice for the given application. Thus, the implementation of a four-switch topology is carried out at a power level of 10 kW. Experimental evaluation is carried out in order to verify the suitability of the circuit for the intended application. The experimental setup validates the findings of the simulations. Thus, the proposed approach is a practical way to improve input current THD and PF compared to thyristor choppers.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4087-4094
Voltage sequence control based high-current rectifier system
This paper presents a thyristor-based tap changing transformer and diode rectifier for variable-voltage high-current DC applications. Back to back thyristors are connected in series with the transformer tappings on the primary side. Thyristors are phase-controlled in a continuous manner to achieve variable AC voltage at the secondary side of the transformer. This leads to a variable DC voltage at the output of three-phase diode rectifier connected at the secondary side of transformer. A passive filter is added at the primary side to achieve power factor improvement over the range of output voltage. This scheme is optimized to determine optimum turns ratio of the transformer and optimum reactive power rating of the passive filter. Design guidelines are presented for various values of power factor along with optimum turns ratios and passive filter rating. A 62.5 kW experimental system with passive filter of 17.5 kVA (reactive) is developed to verify the system performance.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 4087-4094
Voltage sequence control based high-current rectifier system
This paper presents a thyristor-based tap changing transformer and diode rectifier for variable-voltage high-current DC applications. Back to back thyristors are connected in series with the transformer tappings on the primary side. Thyristors are phase-controlled in a continuous manner to achieve variable AC voltage at the secondary side of the transformer. This leads to a variable DC voltage at the output of three-phase diode rectifier connected at the secondary side of transformer. A passive filter is added at the primary side to achieve power factor improvement over the range of output voltage. This scheme is optimized to determine optimum turns ratio of the transformer and optimum reactive power rating of the passive filter. Design guidelines are presented for various values of power factor along with optimum turns ratios and passive filter rating. A 62.5 kW experimental system with passive filter of 17.5 kVA (reactive) is developed to verify the system performance.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 151-156
A completely modular power converter for high-power high-current DC applications
This paper presents a completely modular power supply for high-power and high-current DC applications. The proposed power converter utilizes modular blocks consisting of a half bridge cell followed by an isolated DC-DC converter. The modules are connected in series at the input AC side in the fashion of a modular multilevel rectifier. At the output DC side, the modules are connected in parallel to supply a high-current load. The proposed configuration provides advantages like modularity, isolation, high efficiency, high input power factor, good input current quality and controlled output current over the full operating range. Circuit configuration, control and performance of the proposed system are discussed in detail. Simulation results are presented to verify the performance and effectiveness of the system.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 1553572X,p. 151-156
A completely modular power converter for high-power high-current DC applications
This paper presents a completely modular power supply for high-power and high-current DC applications. The proposed power converter utilizes modular blocks consisting of a half bridge cell followed by an isolated DC-DC converter. The modules are connected in series at the input AC side in the fashion of a modular multilevel rectifier. At the output DC side, the modules are connected in parallel to supply a high-current load. The proposed configuration provides advantages like modularity, isolation, high efficiency, high input power factor, good input current quality and controlled output current over the full operating range. Circuit configuration, control and performance of the proposed system are discussed in detail. Simulation results are presented to verify the performance and effectiveness of the system.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 444-450
A modular multilevel converter based high-power high-current power supply
This paper presents a power supply for high power and high current DC applications. Presently thyristor rectifiers along with passive filters are used in these applications, which suffer from poor input power factor and input current quality problems. The proposed power supply utilizes a modular multilevel rectifier and inverter, medium-frequency transformer and diode rectifier to convert medium-voltage AC to low-voltage DC via a medium-frequency AC link. Configuration provides unique advantages like high efficiency, high input power factor, good input current quality and controlled output current over the full operating range. Circuit configuration, design, control and performance of the proposed system are discussed in detail. Simulation results are presented to verify the performance and effectiveness of the system.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 444-450
A modular multilevel converter based high-power high-current power supply
This paper presents a power supply for high power and high current DC applications. Presently thyristor rectifiers along with passive filters are used in these applications, which suffer from poor input power factor and input current quality problems. The proposed power supply utilizes a modular multilevel rectifier and inverter, medium-frequency transformer and diode rectifier to convert medium-voltage AC to low-voltage DC via a medium-frequency AC link. Configuration provides unique advantages like high efficiency, high input power factor, good input current quality and controlled output current over the full operating range. Circuit configuration, design, control and performance of the proposed system are discussed in detail. Simulation results are presented to verify the performance and effectiveness of the system.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23293721,p. 1725-1732
Analysis, design and control of 1MW, high power factor and high current rectifier system
This paper presents a 1MW, 12-pulse thyristor rectifier with passive filter and DSTATCOM for low voltage, high current industrial dc loads. The considered process act (electrically) as a current controlled, variable voltage load. Moreover the load characteristic varies extensively with number of hours of operation. Variable compensation capabilities are required to provide harmonic and reactive power compensation for such kind of loads. A Distribution Static Compensator (DSTATCOM) is used to provide variable reactive power compensation. Along with it an 11th harmonic passive filter with substantial amount of reactive power support is provided to reduce required rating of DSTATCOM. Design and control of system are carried out such that input power factor remains greater than 0.98 and THD remains below 5%. Simulation results are presented to verify the effectiveness of the system.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23293721,p. 1725-1732
Analysis, design and control of 1MW, high power factor and high current rectifier system
This paper presents a 1MW, 12-pulse thyristor rectifier with passive filter and DSTATCOM for low voltage, high current industrial dc loads. The considered process act (electrically) as a current controlled, variable voltage load. Moreover the load characteristic varies extensively with number of hours of operation. Variable compensation capabilities are required to provide harmonic and reactive power compensation for such kind of loads. A Distribution Static Compensator (DSTATCOM) is used to provide variable reactive power compensation. Along with it an 11th harmonic passive filter with substantial amount of reactive power support is provided to reduce required rating of DSTATCOM. Design and control of system are carried out such that input power factor remains greater than 0.98 and THD remains below 5%. Simulation results are presented to verify the effectiveness of the system.