Yangyang Gao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yangyang Gao has a total of 169 co-authors. Here are the top co-authors by number of shared publications:
- Liqun Zhang
South China University of Technology
35 shared publications - Xiuying Zhao
Beijing University of Chemical Technology
26 shared publications Ruibin Ma
Henan Academy of Sciences
16 shared publications- Jun Liu
Beijing University of Chemical Technology
13 shared publications Xiuying Zhao
Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, Beijing 10029, People's Republic of China
13 shared publicationsHaoxiang Li
State Key Laboratory of Organic−Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 ,People’s Republic of China
11 shared publications
Latest Publications
- 19 September 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (20) , 11558-11572
Differential Coupling of Nanoparticle Translational and Rotational Diffusion to Polymer Relaxation Modes in Unentangled Polymer Melts
The diffusion of spherical nanoparticles (NPs) in unentangled polymer melts is investigated using coarse-grained molecular dynamics simulations. We show that for both translational and rotational diffusion, when the NP diameter d is smaller than a characteristic length lc, the continuum Stokes–Einstein (SE) and Stokes–Einstein–Debye (SED) relations, based on macroscopic viscosity, break down and substantially underestimate the diffusion coefficients. For translational diffusion, the polymer chain size ⟨Ree2〉1/2 defines the relevant length scale, with the characteristic size lcT being a few times ⟨Ree2〉1/2; the SE relation accurately describes the translational diffusion coefficient DT when d>lcT. In contrast, the polymer contour length Nl0 serves as the relevant length scale for rotational diffusion. Recovery of the SED relation is not observed within the simulated NP size range, while extrapolation of the fitted relation to a 90% recovery criterion yields a characteristic recovery length of lcR∼80Nl0, substantially larger than lcT. Analysis of the dynamical coupling between NP motion and polymer relaxation modes reveals that translational and rotational motions exhibit differential coupling behaviors, with rotational diffusion being less strongly coupled to the macroscopic viscosity of the polymer melts. Furthermore, this differential coupling can be modulated by NP–polymer affinity and NP surface bead density. Our findings provide fundamental insights into the mechanisms governing NP dynamics in polymer melts.
- 19 September 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (20) , 11558-11572
Differential Coupling of Nanoparticle Translational and Rotational Diffusion to Polymer Relaxation Modes in Unentangled Polymer Melts
The diffusion of spherical nanoparticles (NPs) in unentangled polymer melts is investigated using coarse-grained molecular dynamics simulations. We show that for both translational and rotational diffusion, when the NP diameter d is smaller than a characteristic length lc, the continuum Stokes–Einstein (SE) and Stokes–Einstein–Debye (SED) relations, based on macroscopic viscosity, break down and substantially underestimate the diffusion coefficients. For translational diffusion, the polymer chain size ⟨Ree2〉1/2 defines the relevant length scale, with the characteristic size lcT being a few times ⟨Ree2〉1/2; the SE relation accurately describes the translational diffusion coefficient DT when d>lcT. In contrast, the polymer contour length Nl0 serves as the relevant length scale for rotational diffusion. Recovery of the SED relation is not observed within the simulated NP size range, while extrapolation of the fitted relation to a 90% recovery criterion yields a characteristic recovery length of lcR∼80Nl0, substantially larger than lcT. Analysis of the dynamical coupling between NP motion and polymer relaxation modes reveals that translational and rotational motions exhibit differential coupling behaviors, with rotational diffusion being less strongly coupled to the macroscopic viscosity of the polymer melts. Furthermore, this differential coupling can be modulated by NP–polymer affinity and NP surface bead density. Our findings provide fundamental insights into the mechanisms governing NP dynamics in polymer melts.
- 1 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (93)
Mobile‐Chain‐Assisted Flow Alignment and Interfacial Adaptation Enable Elastomeric Thermal Interface Materials with High through‐Plane Thermal Conductivity and Low Contact Thermal Resistance
The performance of conventional chemically cross‐linked elastomeric thermal interface materials (E‐TIMs) is fundamentally limited by the intrinsic trade‐off between through‐plane thermal conductivity and interfacial contact resistance. In this work, we propose a mobile‐chain‐assisted flow‐alignment and interfacial‐adaptation strategy by introducing free high‐molecular‐weight hydroxyl‐functional silicone chains into a silicone cross‐linked network. The mobile hydroxyl‐functional chains act as a dual regulator: they facilitate flow‐field‐induced vertical alignment of carbon fibers during extrusion and endow the elastomer matrix with enhanced interfacial wettability, chain mobility, and adaptive conformability. Consequently, the fabricated V‐cSi/fSi‐OH/CF TIM achieves a remarkable through‐plane thermal conductivity of 54.7 W·m −1 ·K −1 . More importantly, the mobile hydroxyl‐functional chains enable near‐conformal interfacial adaptation with heat‐sink surfaces even under a low pressure (1 psi), yielding a calculated contact thermal resistance of 11.2 K·mm 2 ·W −1 (an 84% reduction compared to conventional cross‐linked counterparts). This mobile‐chain‐assisted design strategy provides a generalizable route for developing elastomeric TIMs that combine efficient through‐plane heat conduction with low‐resistance interfacial heat transfer.
- 1 September 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (93)
Mobile‐Chain‐Assisted Flow Alignment and Interfacial Adaptation Enable Elastomeric Thermal Interface Materials with High through‐Plane Thermal Conductivity and Low Contact Thermal Resistance
The performance of conventional chemically cross‐linked elastomeric thermal interface materials (E‐TIMs) is fundamentally limited by the intrinsic trade‐off between through‐plane thermal conductivity and interfacial contact resistance. In this work, we propose a mobile‐chain‐assisted flow‐alignment and interfacial‐adaptation strategy by introducing free high‐molecular‐weight hydroxyl‐functional silicone chains into a silicone cross‐linked network. The mobile hydroxyl‐functional chains act as a dual regulator: they facilitate flow‐field‐induced vertical alignment of carbon fibers during extrusion and endow the elastomer matrix with enhanced interfacial wettability, chain mobility, and adaptive conformability. Consequently, the fabricated V‐cSi/fSi‐OH/CF TIM achieves a remarkable through‐plane thermal conductivity of 54.7 W·m −1 ·K −1 . More importantly, the mobile hydroxyl‐functional chains enable near‐conformal interfacial adaptation with heat‐sink surfaces even under a low pressure (1 psi), yielding a calculated contact thermal resistance of 11.2 K·mm 2 ·W −1 (an 84% reduction compared to conventional cross‐linked counterparts). This mobile‐chain‐assisted design strategy provides a generalizable route for developing elastomeric TIMs that combine efficient through‐plane heat conduction with low‐resistance interfacial heat transfer.
- 17 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (34) , 25121-25133
Influence of Temperature and Pressure on Dynamics and Viscoelasticity of Styrene Butadiene Rubber: Insight from Molecular Dynamics Simulation
In this work, the dynamics and viscoelasticity of styrene butadiene rubber (SBR) are systematically explored for different temperatures (T) and pressures (P), where the coarse-grained model and potential functions are developed by the iterative Boltzmann inversion approach. The simulation results reveal that the dynamics at the monomer and chain scales display different dependencies on T and P. Thus, a time-T-P superposition principle (TTPSP) holds at both the monomer and chain scales for the translational dynamics. However, TTPSP fails at the monomer scale for the relaxation dynamics while remaining valid at the chain scale at a high T. Meanwhile, a low T enhances dynamical heterogeneity, while a high P reduces fragility, which also reduces the monomer mobility. The universal correlations among the relaxation time, corresponding peak height, Debye–Waller factor, T, and P are derived. These indicate the reduced anisotropy of cage shapes at a high P value and some decoupling or coupled relationships. Finally, the storage modulus, loss modulus, and viscosity of SBR are analyzed, which exhibit a gradual increase with decreasing T or increasing P. Interestingly, the viscoelastic properties present a strong relationship with local chain stiffness. TTPSP holds for viscoelasticity at a high T, while it breaks down over the entire T range, which mainly originates from the complex multiscale dynamical behavior of SBR. In summary, this work provides a comprehensive understanding of how temperature and pressure influence the dynamics and viscoelasticity of the SBR.
- 17 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (34) , 25121-25133
Influence of Temperature and Pressure on Dynamics and Viscoelasticity of Styrene Butadiene Rubber: Insight from Molecular Dynamics Simulation
In this work, the dynamics and viscoelasticity of styrene butadiene rubber (SBR) are systematically explored for different temperatures (T) and pressures (P), where the coarse-grained model and potential functions are developed by the iterative Boltzmann inversion approach. The simulation results reveal that the dynamics at the monomer and chain scales display different dependencies on T and P. Thus, a time-T-P superposition principle (TTPSP) holds at both the monomer and chain scales for the translational dynamics. However, TTPSP fails at the monomer scale for the relaxation dynamics while remaining valid at the chain scale at a high T. Meanwhile, a low T enhances dynamical heterogeneity, while a high P reduces fragility, which also reduces the monomer mobility. The universal correlations among the relaxation time, corresponding peak height, Debye–Waller factor, T, and P are derived. These indicate the reduced anisotropy of cage shapes at a high P value and some decoupling or coupled relationships. Finally, the storage modulus, loss modulus, and viscosity of SBR are analyzed, which exhibit a gradual increase with decreasing T or increasing P. Interestingly, the viscoelastic properties present a strong relationship with local chain stiffness. TTPSP holds for viscoelasticity at a high T, while it breaks down over the entire T range, which mainly originates from the complex multiscale dynamical behavior of SBR. In summary, this work provides a comprehensive understanding of how temperature and pressure influence the dynamics and viscoelasticity of the SBR.
- 14 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
Investigation of heat transfer in a semicrystalline polymer by combining molecular simulation and machine learning
Heat transfer in a semicrystalline polymer is investigated by combining molecular simulation and machine learning and the molecular mechanism is discussed.
- 14 May 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
Investigation of heat transfer in a semicrystalline polymer by combining molecular simulation and machine learning
Heat transfer in a semicrystalline polymer is investigated by combining molecular simulation and machine learning and the molecular mechanism is discussed.
- 4 March 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (15) , 8234-8248
Molecular mechanism of the fracture properties of slide-ring crosslinked elastomers
The effect of crosslink density and coverage of the slide-rings on the properties and molecular mechanism of the fracture of slide-ring crosslinked elastomers is investigated by adopting a coarse-grained model.
- 4 March 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (15) , 8234-8248
Molecular mechanism of the fracture properties of slide-ring crosslinked elastomers
The effect of crosslink density and coverage of the slide-rings on the properties and molecular mechanism of the fracture of slide-ring crosslinked elastomers is investigated by adopting a coarse-grained model.
- 4 December 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (50) , 17285-17294
Low Contact Thermal Resistance without Packaging Pressure in Highly Thermally Conductive Interface Materials Enabled by Polysulfide Vitrimer
Thermal interface materials (TIMs) are essential for enhancing interfacial heat transfer, yet achieving both high through-plane thermal conductivity (κ⊥) and structural conformability remains difficult. This study introduces a vitrimer-based TIM using a diglycidyl-ether end-capped liquid polysulfide prepolymer (EPS), where stress relaxation from dynamic covalent bonds improves interfacial contact. A vertically aligned graphite composite (VAGC) with high κ⊥ (15.5 W m-1 K-1) was fabricated via a combined hot-pressing and "stacking-welding" method. Driven by unstable dynamics from a reversible topological network and high surface free energy of thermodynamic properties, VAGC exhibits spontaneous contact behavior. Under zero pressure, the contact thermal resistance drops sharply at 80-100 °C and reaches 16.4 mm2 K W-1, while the effective thermal conductivity of VAGC reaches 14.4 W m-1 K-1. It is believed that the novel EPS vitrimer offers a promising polymer matrix for advanced TIMs.
- 4 December 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (50) , 17285-17294
Low Contact Thermal Resistance without Packaging Pressure in Highly Thermally Conductive Interface Materials Enabled by Polysulfide Vitrimer
Thermal interface materials (TIMs) are essential for enhancing interfacial heat transfer, yet achieving both high through-plane thermal conductivity (κ⊥) and structural conformability remains difficult. This study introduces a vitrimer-based TIM using a diglycidyl-ether end-capped liquid polysulfide prepolymer (EPS), where stress relaxation from dynamic covalent bonds improves interfacial contact. A vertically aligned graphite composite (VAGC) with high κ⊥ (15.5 W m-1 K-1) was fabricated via a combined hot-pressing and "stacking-welding" method. Driven by unstable dynamics from a reversible topological network and high surface free energy of thermodynamic properties, VAGC exhibits spontaneous contact behavior. Under zero pressure, the contact thermal resistance drops sharply at 80-100 °C and reaches 16.4 mm2 K W-1, while the effective thermal conductivity of VAGC reaches 14.4 W m-1 K-1. It is believed that the novel EPS vitrimer offers a promising polymer matrix for advanced TIMs.
- 8 September 2025
- Published by Elsevier in Journal of Membrane Science
- Vol. 736
One-pot prepared highly interface-compatible and ion-selective polymer-SCOF composite membrane for vanadium flow battery
- 8 September 2025
- Published by Elsevier in Journal of Membrane Science
- Vol. 736
One-pot prepared highly interface-compatible and ion-selective polymer-SCOF composite membrane for vanadium flow battery
- Open Access
- 26 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (9) , 4822
Research on the Effects of Poly(Styrene-co-Butyl Acrylate) Emulsions on the Mechanical and Fracture Characteristics of Mortar
A series of poly(styrene-co-butyl acrylate) (PSA) emulsions with different monomer ratios were synthesized and characterized, and corresponding polymer-modified mortars were prepared. The effects of polymers with different rigidities on the properties of modified mortars, including the hydration heat, mechanical strength, compressive–flexural ratio, fracture energy, and fracture toughness, were investigated. The results indicate that, as the content of hard monomers in the polymer increases, the fracture energy of the modified mortar first increases and then decreases, consistent with the changes in the polymer’s damping properties. The maximum fracture energy of 211.2 N/m was achieved at a St/BA mass ratio of 4:6 and a polymer-to-cement ratio (P/C) of 15%, which was 2.4 times higher than that of the control mortar group. The fracture toughness of the modified mortar decreased with an increasing polymer doping and decreasing hard monomer content. The compressive–flexural ratio of the modified mortar decreased only with increasing the polymer emulsion dosage, showing no significant correlation with the polymer’s molecular structure.
- 26 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (9) , 4822
Open AccessResearch on the Effects of Poly(Styrene-co-Butyl Acrylate) Emulsions on the Mechanical and Fracture Characteristics of Mortar
A series of poly(styrene-co-butyl acrylate) (PSA) emulsions with different monomer ratios were synthesized and characterized, and corresponding polymer-modified mortars were prepared. The effects of polymers with different rigidities on the properties of modified mortars, including the hydration heat, mechanical strength, compressive–flexural ratio, fracture energy, and fracture toughness, were investigated. The results indicate that, as the content of hard monomers in the polymer increases, the fracture energy of the modified mortar first increases and then decreases, consistent with the changes in the polymer’s damping properties. The maximum fracture energy of 211.2 N/m was achieved at a St/BA mass ratio of 4:6 and a polymer-to-cement ratio (P/C) of 15%, which was 2.4 times higher than that of the control mortar group. The fracture toughness of the modified mortar decreased with an increasing polymer doping and decreasing hard monomer content. The compressive–flexural ratio of the modified mortar decreased only with increasing the polymer emulsion dosage, showing no significant correlation with the polymer’s molecular structure.