Eugênio José Zoqui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Eugênio José Zoqui has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Luis Vanderlei Torres
Instituto Federal de Educação, Ciência e Tecnologia de São Paulo, Brasil
13 shared publications - Cecília Tereza Weishaupt Proni
UNICAMP, Brazil
11 shared publications Luis Vanderlei Torres
São Paulo Federal Institute of Education
10 shared publications- Gabriela Lujan Brollo
University of Campinas – Unicamp
9 shared publications - Davi Munhoz Benati
University of Campinas
8 shared publications - Hipólito Carvajal Fals
Faculty of Mechanical Engineering, University of Campinas, UNICAMP, Campinas, Brazil
7 shared publications
Latest Publications
- 4 September 2026
- Published by SAGE Publications in Materials Science and Technology
Influence of electromagnetic stirring and grain refinement on solidification defects in Al6Si2.5Cu alloy via X-ray computed tomography
This study investigates the combined effects of electromagnetic stirring (EMS) and chemical grain refinement (CGR) on solidification discontinuities in an Al-6wt%Si-2.5wt%Cu (Al6Si2.5Cu) alloy using 3D X-ray Computed Tomography. Results show that integrating EMS with an Al-5Ti-1B master alloy reduces the average grain size by 23.4% compared with CGR alone. This microstructural refinement produces a pronounced 57.95% reduction in total discontinuity volume and exhibits a near-cubic power-law dependence on grain size, with an exponent of 3.25. While the low-sphericity morphology characteristic of shrinkage cavities remains unchanged, the synergistic CGR + EMS treatment restricts the maximum defect size to below 0.4 mm, yielding a smaller, more homogeneously distributed defect population optimized for high-quality engineering components.
- 4 September 2026
- Published by SAGE Publications in Materials Science and Technology
Influence of electromagnetic stirring and grain refinement on solidification defects in Al6Si2.5Cu alloy via X-ray computed tomography
This study investigates the combined effects of electromagnetic stirring (EMS) and chemical grain refinement (CGR) on solidification discontinuities in an Al-6wt%Si-2.5wt%Cu (Al6Si2.5Cu) alloy using 3D X-ray Computed Tomography. Results show that integrating EMS with an Al-5Ti-1B master alloy reduces the average grain size by 23.4% compared with CGR alone. This microstructural refinement produces a pronounced 57.95% reduction in total discontinuity volume and exhibits a near-cubic power-law dependence on grain size, with an exponent of 3.25. While the low-sphericity morphology characteristic of shrinkage cavities remains unchanged, the synergistic CGR + EMS treatment restricts the maximum defect size to below 0.4 mm, yielding a smaller, more homogeneously distributed defect population optimized for high-quality engineering components.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Analysis of the microstructural behavior of the Al4.5Cu5Zn semisolid alloy during partial remelting
This work aims to contribute to metal processing in the semisolid state by analyzing the microstructural behavior of the Al4.5Cu5Zn under two production routes: conventional (without a grain-refining alloy) and grain refinement. The alloy was reheated to the working temperature corresponding to a 45% solid fraction (608 °C) and maintained for various heat treatment times; the samples were then examined using metallographic techniques to evaluate their behavior. The conventionally produced alloy samples showed deficiencies in primary globule size, grain size, circularity shape factor, and rheocast quality index. Conversely, the samples produced via the grain refinement method yielded satisfactory results across all analyzed parameters, with a 55 μm reduction in average primary globule size, a 25 μm decrease in average grain size, a 0.10 increase in the circularity shape factor, and a 0.03 increase in the rheocast quality index. Additionally, the reheating treatment time influenced the results, with 60 seconds identified as the optimal duration for both production routes. This suggests that the phenomena of Ostwald ripening and coalescence primarily occur within this timeframe. Specifically, as treatment time increases, smaller dendritic arms dissolve and are incorporated into larger ones, reducing the number of dendritic arms (Ostwald ripening), while secondary dendritic arms also tend to coalesce (coalescence).
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 31
Open AccessAnalysis of the microstructural behavior of the Al4.5Cu5Zn semisolid alloy during partial remelting
This work aims to contribute to metal processing in the semisolid state by analyzing the microstructural behavior of the Al4.5Cu5Zn under two production routes: conventional (without a grain-refining alloy) and grain refinement. The alloy was reheated to the working temperature corresponding to a 45% solid fraction (608 °C) and maintained for various heat treatment times; the samples were then examined using metallographic techniques to evaluate their behavior. The conventionally produced alloy samples showed deficiencies in primary globule size, grain size, circularity shape factor, and rheocast quality index. Conversely, the samples produced via the grain refinement method yielded satisfactory results across all analyzed parameters, with a 55 μm reduction in average primary globule size, a 25 μm decrease in average grain size, a 0.10 increase in the circularity shape factor, and a 0.03 increase in the rheocast quality index. Additionally, the reheating treatment time influenced the results, with 60 seconds identified as the optimal duration for both production routes. This suggests that the phenomena of Ostwald ripening and coalescence primarily occur within this timeframe. Specifically, as treatment time increases, smaller dendritic arms dissolve and are incorporated into larger ones, reducing the number of dendritic arms (Ostwald ripening), while secondary dendritic arms also tend to coalesce (coalescence).
- 24 April 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (21) , 24574-24588
Machine Learning Algorithms Model Applied to Predict Mechanical Properties of Thixoformed Al-6wt.%Si-2.5wt.%Cu Alloy
- 24 April 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (21) , 24574-24588
Machine Learning Algorithms Model Applied to Predict Mechanical Properties of Thixoformed Al-6wt.%Si-2.5wt.%Cu Alloy
- 22 April 2025
- Published by SAGE Publications in Materials Science and Technology
- Vol. 42 (14) , 1404-1419
Tailoring 7075 alloys for semisolid state processing via in-situ formed TiAl 3
Traditional 7075 aluminum alloys are difficult to cast due to low viscosity and high shrinkage. This study addresses these challenges by forming TiAl 3 particles in situ, which enhance viscosity, reduce porosity, and prevent shrinkage cracks. The method involves adding a titanium master alloy to molten 7075 and using mechanical stirring to induce TiAl 3 formation. This improves processability, making the alloy suitable for high-pressure die casting (HPDC) in the aerospace and automotive industries. Microstructural analysis confirms that uniformly distributed TiAl 3 particles refine grains and enhance stability. The study employs microscopy, X-ray diffraction, thermodynamic simulations, and mechanical testing to validate structural properties, advancing 7075 alloy processing for large-scale applications in semisolid techniques.
- 22 April 2025
- Published by SAGE Publications in Materials Science and Technology
- Vol. 42 (14) , 1404-1419
Tailoring 7075 alloys for semisolid state processing via in-situ formed TiAl 3
Traditional 7075 aluminum alloys are difficult to cast due to low viscosity and high shrinkage. This study addresses these challenges by forming TiAl 3 particles in situ, which enhance viscosity, reduce porosity, and prevent shrinkage cracks. The method involves adding a titanium master alloy to molten 7075 and using mechanical stirring to induce TiAl 3 formation. This improves processability, making the alloy suitable for high-pressure die casting (HPDC) in the aerospace and automotive industries. Microstructural analysis confirms that uniformly distributed TiAl 3 particles refine grains and enhance stability. The study employs microscopy, X-ray diffraction, thermodynamic simulations, and mechanical testing to validate structural properties, advancing 7075 alloy processing for large-scale applications in semisolid techniques.
- 1 April 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (1) , 132-149
Die Casting, Rheocasting, or Thixoforming? Comparison of Production Strategies Using the 356 Aluminum Alloy
- 1 April 2025
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 20 (1) , 132-149
Die Casting, Rheocasting, or Thixoforming? Comparison of Production Strategies Using the 356 Aluminum Alloy
- 11 November 2024
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 56 (1) , 342-354
Aluminum–Titanium Alloys: A Possible New Frontier for SSM Processing
- 11 November 2024
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 56 (1) , 342-354
Aluminum–Titanium Alloys: A Possible New Frontier for SSM Processing
- 7 June 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (5) , 862-870
Microstructural Stability of Al3Si2.5Cu Alloy in the Semisolid State Produced via Deformation via Equal Channel Angular Pressing (ECAP)
- 7 June 2024
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 13 (5) , 862-870
Microstructural Stability of Al3Si2.5Cu Alloy in the Semisolid State Produced via Deformation via Equal Channel Angular Pressing (ECAP)
- Open Access
Rheological Characterization of a Thixotropic Semisolid Slurry by Means of Numerical Simulations of Squeeze-Flow Experiments
We propose a methodology for the rheological characterization of a semisolid metal slurry using experimental squeeze-flow data. The slurry is modeled as a structural thixotropic viscoplastic material, obeying the regularized Herschel–Bulkley constitutive equation. All rheological parameters are assumed to vary with the structure parameter that is governed by first-order kinetics accounting for the material structure breakdown and build-up. The squeeze flow is simulated using finite elements in a Lagrangian framework. The evolution of the sample height has been studied for wide ranges of the Bingham and Reynolds numbers, the power-law exponent as well as the kinetics parameters of the structure parameter. Systematic comparisons have been carried out with available experimental data on a semisolid aluminum alloy (A356), where the sample is compressed from its top side under a specified strain of 80% at a temperature of 582 °C, while the bottom side remains fixed. Excellent agreement with the experimental data could be achieved provided that at the initial instances (up to 0.01 s) of the experiment, the applied load is much higher than the nominal experimental load and that the yield stress and the power-law exponent vary linearly with the structure parameter. The first assumption implies that a different model, such as an elastoviscoplastic one, needs to be employed during the initial stages of the experiment. As for the second one, the evolution of the sample height can be reproduced allowing the yield stress to vary from 0 (no structure) to a maximum nominal value (full structure) and the power-law exponent from 0.2 to 1.4, i.e., from the shear-thinning to the shear-thickening regime. These variations are consistent with the internal microstructure variation pattern known to be exhibited by semisolid slurries.
Open AccessRheological Characterization of a Thixotropic Semisolid Slurry by Means of Numerical Simulations of Squeeze-Flow Experiments
We propose a methodology for the rheological characterization of a semisolid metal slurry using experimental squeeze-flow data. The slurry is modeled as a structural thixotropic viscoplastic material, obeying the regularized Herschel–Bulkley constitutive equation. All rheological parameters are assumed to vary with the structure parameter that is governed by first-order kinetics accounting for the material structure breakdown and build-up. The squeeze flow is simulated using finite elements in a Lagrangian framework. The evolution of the sample height has been studied for wide ranges of the Bingham and Reynolds numbers, the power-law exponent as well as the kinetics parameters of the structure parameter. Systematic comparisons have been carried out with available experimental data on a semisolid aluminum alloy (A356), where the sample is compressed from its top side under a specified strain of 80% at a temperature of 582 °C, while the bottom side remains fixed. Excellent agreement with the experimental data could be achieved provided that at the initial instances (up to 0.01 s) of the experiment, the applied load is much higher than the nominal experimental load and that the yield stress and the power-law exponent vary linearly with the structure parameter. The first assumption implies that a different model, such as an elastoviscoplastic one, needs to be employed during the initial stages of the experiment. As for the second one, the evolution of the sample height can be reproduced allowing the yield stress to vary from 0 (no structure) to a maximum nominal value (full structure) and the power-law exponent from 0.2 to 1.4, i.e., from the shear-thinning to the shear-thickening regime. These variations are consistent with the internal microstructure variation pattern known to be exhibited by semisolid slurries.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 27, e20240314
The Influence of Ultrasonic Melt Treatment on Microstructural Evaluation of the Al7Si2.5Cu Alloy for Semisolid Processing
Obtaining a refined microstructure is the first step for using it in thixoforming processes. However, the chemical refining of the grain of aluminum alloys with high silicon content is impaired; therefore, grain refining via UST (Ultrasonic Melt Treatment) is a possible solution for these cases. This work aims to analyze the microstructural stability of the microstructure of the Al7Si2.5Cu alloy in the semisolid state. The material was prepared by conventional casting and submitted to processing via UST for 20 seconds with a steel horn. The material underwent reheating heat treatment for 0, 30, 60, 90, and 210 seconds under two solid fractions of 45% and 60%, respectively, 572 and 565 °C. The results show an average primary globule size of around 88 μm and a circularity form factor above 0.50. Regarding the eutectic morphology, it was quite fragmented when processed via UST; that is, the application of acoustic waves in the liquid metal causes it to mix effectively, and it is also capable of breaking the coarser Si particles. When comparing the microstructural evolution of the Al7Si2.5Cu alloy via UST with the ultra-grain refining technique, UST presents superior results in all analyzed scenarios.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 27, e20240314
Open AccessThe Influence of Ultrasonic Melt Treatment on Microstructural Evaluation of the Al7Si2.5Cu Alloy for Semisolid Processing
Obtaining a refined microstructure is the first step for using it in thixoforming processes. However, the chemical refining of the grain of aluminum alloys with high silicon content is impaired; therefore, grain refining via UST (Ultrasonic Melt Treatment) is a possible solution for these cases. This work aims to analyze the microstructural stability of the microstructure of the Al7Si2.5Cu alloy in the semisolid state. The material was prepared by conventional casting and submitted to processing via UST for 20 seconds with a steel horn. The material underwent reheating heat treatment for 0, 30, 60, 90, and 210 seconds under two solid fractions of 45% and 60%, respectively, 572 and 565 °C. The results show an average primary globule size of around 88 μm and a circularity form factor above 0.50. Regarding the eutectic morphology, it was quite fragmented when processed via UST; that is, the application of acoustic waves in the liquid metal causes it to mix effectively, and it is also capable of breaking the coarser Si particles. When comparing the microstructural evolution of the Al7Si2.5Cu alloy via UST with the ultra-grain refining technique, UST presents superior results in all analyzed scenarios.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (2) , e20240038
Refino de grão versus agitação eletromagnética: caracterização microestrutural e mecânica da liga Al4Si2.5Cu tixoforjada
RESUMO O objetivo deste trabalho foi avaliar a tixoconformabilidade da liga Al4Si2.5Cu sob duas diferentes rotas de produção: técnica via refino de grão e via agitação eletromagnética, abrangendo desde a obtenção da liga até sua caracterização microestrutural e mecânica após o processo de tixoforjamento em uma prensa excêntrica mecânica. A liga foi submetida a tratamentos térmicos de globularização que promovem a globularização das partículas de fase primária pelos tempos de 0s e 210s na fração sólida de 45% e na sequencia tixoforjada. Os ensaios de tixoforjamento mostraram que a força necessária de fechamento da matriz é praticamente constante, independentemente do tempo de globularização, ficando em torno de 70 kN, utilizando menos de um terço da capacidade da prensa. Com relação a sua morfologia para ambas as rotas de produção, a mesma apresentou morfologia globular para ambos os tempos de tratamento térmico. As peças tixoforjadas apresentaram boa conformabilidade preenchendo toda a matriz e reproduzindo sua geometria, além de apresentar boas propriedades mecânicas nos ensaios de tração, ou seja, o valor limite de resistência à tração principalmente quando utilizado a rota de produção via agitação eletromagnética apresentou valores próximos a 200 MPa. Demonstrando que a liga torna-se propicia aos processos de tixoconformação.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (2) , e20240038
Open AccessRefino de grão versus agitação eletromagnética: caracterização microestrutural e mecânica da liga Al4Si2.5Cu tixoforjada
RESUMO O objetivo deste trabalho foi avaliar a tixoconformabilidade da liga Al4Si2.5Cu sob duas diferentes rotas de produção: técnica via refino de grão e via agitação eletromagnética, abrangendo desde a obtenção da liga até sua caracterização microestrutural e mecânica após o processo de tixoforjamento em uma prensa excêntrica mecânica. A liga foi submetida a tratamentos térmicos de globularização que promovem a globularização das partículas de fase primária pelos tempos de 0s e 210s na fração sólida de 45% e na sequencia tixoforjada. Os ensaios de tixoforjamento mostraram que a força necessária de fechamento da matriz é praticamente constante, independentemente do tempo de globularização, ficando em torno de 70 kN, utilizando menos de um terço da capacidade da prensa. Com relação a sua morfologia para ambas as rotas de produção, a mesma apresentou morfologia globular para ambos os tempos de tratamento térmico. As peças tixoforjadas apresentaram boa conformabilidade preenchendo toda a matriz e reproduzindo sua geometria, além de apresentar boas propriedades mecânicas nos ensaios de tração, ou seja, o valor limite de resistência à tração principalmente quando utilizado a rota de produção via agitação eletromagnética apresentou valores próximos a 200 MPa. Demonstrando que a liga torna-se propicia aos processos de tixoconformação.