Ernesto Rodriguez-Leal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ernesto Rodriguez-Leal has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Gordon R. Pennock
Purdue Univ, Sch Mech Engn, W Lafayette, IN 47907 USA
3 shared publications Eduardo Piña-Martínez
School of Engineering and Sciences, Tecnológico de Monterrey
2 shared publications- Jian Sheng Dai
King’s College London
2 shared publications - Ricardo Roberts
Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, USA
2 shared publications - Carlos Hernandez-Santos
Tecnológico Nacional de México/IT de Nuevo León, México, Av. Eloy Cavazos 2001, Guadalupe 66170, Nuevo León, Mexico
1 shared publication - Eduardo Piña-Martínez
Escuela de Ingeniería y Ciencias, Ave. Eugenio Garza Sada 2501, Tecnologico de Monterrey, 64849 Monterrey, NL, Mexico
1 shared publication
Latest Publications
- Open Access
- 3 June 2018
- Published by Wiley in Applied Bionics and Biomechanics
- Vol. 2018, 1-14
Vision System-Based Design and Assessment of a Novel Shoulder Joint Mechanism for an Enhanced Workspace Upper Limb Exoskeleton
Exoskeletons arise as the common ground between robotics and biomechanics, where rehabilitation is the main field in which these two disciplines find cohesion. One of the most relevant challenges in upper limb exoskeleton design relies in the high complexity of the human shoulder, where current devices implement elaborate systems only to emulate the drifting center of rotation of the shoulder joint. This paper proposes the use of 3D scanning vision technologies to ease the design process and its implementation on a variety of subjects, while a motion tracking system based on vision technologies is applied to assess the exoskeleton reachable workspace compared with an asymptomatic subject. Furthermore, the anatomic fitting index is proposed, which compares the anatomic workspace of the user with the exoskeleton workspace and provides insight into its features. This work proposes an exoskeleton architecture that considers the clavicle motion over the coronal plane whose workspace is determined by substituting the direct kinematics model with the dimensional parameters of the user. Simulations and numerical examples are used to validate the analytical results and to conciliate the experimental results provided by the vision tracking system.
- 3 June 2018
- Published by Wiley in Applied Bionics and Biomechanics
- Vol. 2018, 1-14
Open AccessVision System-Based Design and Assessment of a Novel Shoulder Joint Mechanism for an Enhanced Workspace Upper Limb Exoskeleton
Exoskeletons arise as the common ground between robotics and biomechanics, where rehabilitation is the main field in which these two disciplines find cohesion. One of the most relevant challenges in upper limb exoskeleton design relies in the high complexity of the human shoulder, where current devices implement elaborate systems only to emulate the drifting center of rotation of the shoulder joint. This paper proposes the use of 3D scanning vision technologies to ease the design process and its implementation on a variety of subjects, while a motion tracking system based on vision technologies is applied to assess the exoskeleton reachable workspace compared with an asymptomatic subject. Furthermore, the anatomic fitting index is proposed, which compares the anatomic workspace of the user with the exoskeleton workspace and provides insight into its features. This work proposes an exoskeleton architecture that considers the clavicle motion over the coronal plane whose workspace is determined by substituting the direct kinematics model with the dimensional parameters of the user. Simulations and numerical examples are used to validate the analytical results and to conciliate the experimental results provided by the vision tracking system.
- 13 October 2016
- Published by Springer Nature
- p. 1199-1203
A Novel Exoskeleton for Continuous Monitoring of the Upper-Limb During Gross Motor Rehabilitation
- 13 October 2016
- Published by Springer Nature
- p. 1199-1203
A Novel Exoskeleton for Continuous Monitoring of the Upper-Limb During Gross Motor Rehabilitation
- Open Access
- 1 January 2015
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2015, 1-14
Inverse Modeling of Human Knee Joint Based on Geometry and Vision Systems for Exoskeleton Applications
Current trends in Robotics aim to close the gap that separates technology and humans, bringing novel robotic devices in order to improve human performance. Although robotic exoskeletons represent a breakthrough in mobility enhancement, there are design challenges related to the forces exerted to the users’ joints that result in severe injuries. This occurs due to the fact that most of the current developments consider the joints as noninvariant rotational axes. This paper proposes the use of commercial vision systems in order to perform biomimetic joint design for robotic exoskeletons. This work proposes a kinematic model based on irregular shaped cams as the joint mechanism that emulates the bone-to-bone joints in the human body. The paper follows a geometric approach for determining the location of the instantaneous center of rotation in order to design the cam contours. Furthermore, the use of a commercial vision system is proposed as the main measurement tool due to its noninvasive feature and for allowing subjects under measurement to move freely. The application of this method resulted in relevant information about the displacements of the instantaneous center of rotation at the human knee joint.
- 1 January 2015
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2015, 1-14
Open AccessInverse Modeling of Human Knee Joint Based on Geometry and Vision Systems for Exoskeleton Applications
Current trends in Robotics aim to close the gap that separates technology and humans, bringing novel robotic devices in order to improve human performance. Although robotic exoskeletons represent a breakthrough in mobility enhancement, there are design challenges related to the forces exerted to the users’ joints that result in severe injuries. This occurs due to the fact that most of the current developments consider the joints as noninvariant rotational axes. This paper proposes the use of commercial vision systems in order to perform biomimetic joint design for robotic exoskeletons. This work proposes a kinematic model based on irregular shaped cams as the joint mechanism that emulates the bone-to-bone joints in the human body. The paper follows a geometric approach for determining the location of the instantaneous center of rotation in order to design the cam contours. Furthermore, the use of a commercial vision system is proposed as the main measurement tool due to its noninvasive feature and for allowing subjects under measurement to move freely. The application of this method resulted in relevant information about the displacements of the instantaneous center of rotation at the human knee joint.
- Open Access
- 28 November 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-9
Screw-System-Based Mobility Analysis of a Family of Fully Translational Parallel Manipulators
This paper investigates the mobility of a family of fully translational parallel manipulators based on screw system analysis by identifying the common constraint and redundant constraints, providing a case study of this approach. The paper presents the branch motion-screws for the 3-RC-Y parallel manipulator, the 3-RCC-Y (or 3-RRC-Y) parallel manipulator, and a newly proposed 3-RC-T parallel manipulator. Then the paper determines the sets of platform constraint-screws for each of these three manipulators. The constraints exerted on the platforms of the 3-RCarchitectures and the 3-RCC-Y manipulators are analyzed using the screw system approach and have been identified as couples. A similarity has been identified with the axes of couples: they are perpendicular to theRjoint axes, but in the former the axes are coplanar with the base and in the latter the axes are perpendicular to the limb. The remaining couples act about the axis that is normal to the base. The motion-screw system and constraint-screw system analysis leads to the insightful understanding of the mobility of the platform that is then obtained by determining the reciprocal screws to the platform constraint screw sets, resulting in three independent instantaneous translational degrees-of-freedom. To validate the mobility analysis of the three parallel manipulators, the paper includes motion simulations which use a commercially available kinematics software.- 28 November 2013
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2013, 1-9
Open AccessScrew-System-Based Mobility Analysis of a Family of Fully Translational Parallel Manipulators
This paper investigates the mobility of a family of fully translational parallel manipulators based on screw system analysis by identifying the common constraint and redundant constraints, providing a case study of this approach. The paper presents the branch motion-screws for the 3-RC-Y parallel manipulator, the 3-RCC-Y (or 3-RRC-Y) parallel manipulator, and a newly proposed 3-RC-T parallel manipulator. Then the paper determines the sets of platform constraint-screws for each of these three manipulators. The constraints exerted on the platforms of the 3-RCarchitectures and the 3-RCC-Y manipulators are analyzed using the screw system approach and have been identified as couples. A similarity has been identified with the axes of couples: they are perpendicular to theRjoint axes, but in the former the axes are coplanar with the base and in the latter the axes are perpendicular to the limb. The remaining couples act about the axis that is normal to the base. The motion-screw system and constraint-screw system analysis leads to the insightful understanding of the mobility of the platform that is then obtained by determining the reciprocal screws to the platform constraint screw sets, resulting in three independent instantaneous translational degrees-of-freedom. To validate the mobility analysis of the three parallel manipulators, the paper includes motion simulations which use a commercially available kinematics software. - Open Access
- 1 November 2012
- Published by SAGE Publications in International Journal of Advanced Robotic Systems
- Vol. 9 (5)
Kinematics and Dynamics of a New 16 DOF Humanoid Biped Robot with Active Toe Joint
Humanoid biped robots are typically complex in design, having numerous Degrees-of-Freedom (DOF) due to the ambitious goal of mimicking the human gait. The paper proposes a new architecture for a biped robot with seven DOF per each leg and one DOF corresponding to the toe joint. Furthermore, this work presents close equations for the forward and inverse kinematics by dividing the walking gait into the Sagittal and Frontal planes. This paper explains the mathematical model of the dynamics equations for the legs into the Sagittal and Frontal planes by further applying the principle of Lagrangian dynamics. Finally, a control approach using a PD control law with gravity compensation was recurred in order to control the desired trajectories and finding the required torque by the joints. The paper contains several simulations and numerical examples to prove the analytical results, using SimMechanics of MATLAB toolbox and SolidWorks to verify the analytical results.
- 1 November 2012
- Published by SAGE Publications in International Journal of Advanced Robotic Systems
- Vol. 9 (5)
Open AccessKinematics and Dynamics of a New 16 DOF Humanoid Biped Robot with Active Toe Joint
Humanoid biped robots are typically complex in design, having numerous Degrees-of-Freedom (DOF) due to the ambitious goal of mimicking the human gait. The paper proposes a new architecture for a biped robot with seven DOF per each leg and one DOF corresponding to the toe joint. Furthermore, this work presents close equations for the forward and inverse kinematics by dividing the walking gait into the Sagittal and Frontal planes. This paper explains the mathematical model of the dynamics equations for the legs into the Sagittal and Frontal planes by further applying the principle of Lagrangian dynamics. Finally, a control approach using a PD control law with gravity compensation was recurred in order to control the desired trajectories and finding the required torque by the joints. The paper contains several simulations and numerical examples to prove the analytical results, using SimMechanics of MATLAB toolbox and SolidWorks to verify the analytical results.
- 13 June 2012
- Published by Springer Nature
- p. 355-369
A Study of the Instantaneous Kinematics of the 5-RSP Parallel Mechanism Using Screw Theory
- 13 June 2012
- Published by Springer Nature
- p. 355-369
A Study of the Instantaneous Kinematics of the 5-RSP Parallel Mechanism Using Screw Theory
- 18 January 2011
- Published by Springer Nature in Meccanica
- Vol. 46 (1) , 221-237
Kinematic analysis of a 5-R SP parallel mechanism with centralized motion
- 18 January 2011
- Published by Springer Nature in Meccanica
- Vol. 46 (1) , 221-237
Kinematic analysis of a 5-R SP parallel mechanism with centralized motion