Hunju Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hunju Lee has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
Seung-Hyun Moon
SuNam Company Ltd., Anseong, South Korea
7 shared publicationsJae-Hun Lee
SuNam Company Ltd., Anseong, South Korea
4 shared publicationsKyekun Cheon
SuNAM Company Ltd., Anseong, Korea
3 shared publicationsS.H. Moon
SuNAM Co., Ltd., Anseong-si, Gyeonggi-do, 456-812, Korea
3 shared publicationsSangwon Yoon
SuNAM, 52 Seungnyang-gil, Wongok-myeon, Anseong-si, Gyeonggi-do 17554, South Korea
3 shared publications- Young-Soon Kim
Institute of Carbon Technology, Jeonju University, Jeonju 55069, Republic of Korea
3 shared publications
Latest Publications
- 20 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Superconducting Properties of Several HTS GdBCO Coated Conductors
The superconducting properties of four high-temperature superconducting (HTS) GdBCO coated conductors (CCs) with GdBCO film thicknesses ranging from 1.04 to 1.65 µm have been analyzed. The crystallinity of the GdBCO superconducting layer showed no significant change as the film thickness increased. The transport critical current (Ic) values exhibited a linear increase with thickness, while the critical current density (Jc) remained consistent despite the increased thickness. The magnetic properties of all HTS GdBCO CCs were investigated using a commercial Quantum Design SQUID-VSM. The lower critical field (Hc1), penetration field (Hp), and irreversibility magnetic field (Hirr) were estimated from their magnetic moment m(H) curves. The temperature dependence of Hc1, Hp, and Hirr was found to be nearly independent of GdBCO film thicknesses. Additionally, the critical current density Jc values were derived from the irreversible magnetic moment Δm(H) data using a modified Bean model. Across all temperatures, the resulting Jc(t) values remained largely unchanged with increasing GdBCO film thickness (t).
- 20 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-6
The Superconducting Properties of Several HTS GdBCO Coated Conductors
The superconducting properties of four high-temperature superconducting (HTS) GdBCO coated conductors (CCs) with GdBCO film thicknesses ranging from 1.04 to 1.65 µm have been analyzed. The crystallinity of the GdBCO superconducting layer showed no significant change as the film thickness increased. The transport critical current (Ic) values exhibited a linear increase with thickness, while the critical current density (Jc) remained consistent despite the increased thickness. The magnetic properties of all HTS GdBCO CCs were investigated using a commercial Quantum Design SQUID-VSM. The lower critical field (Hc1), penetration field (Hp), and irreversibility magnetic field (Hirr) were estimated from their magnetic moment m(H) curves. The temperature dependence of Hc1, Hp, and Hirr was found to be nearly independent of GdBCO film thicknesses. Additionally, the critical current density Jc values were derived from the irreversible magnetic moment Δm(H) data using a modified Bean model. Across all temperatures, the resulting Jc(t) values remained largely unchanged with increasing GdBCO film thickness (t).
- 28 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Design and Evaluation of Prototype High-Tc Superconducting Linear Synchronous Motor for High-Speed Transportation
We developed a prototype of a high-Tc superconducting (HTS) linear synchronous motor (LSM) and evaluated its operational performances to obtain the preliminary design data for a test vehicle having a speed of 518.4 km/h. The HTS electromagnet was fabricated using a non-insulated (NI) GdBCO HTS coil, which was designed to produce a magnetomotive force of 300 kA-turns at a cooling temperature of 20 K. A two-stage Gifford-McMahon cryocooler was used to cool the electromagnet. The prototype was tested up to 2.7 kN sufficient to the required thrust of the test vehicle. The thrust characteristics shown by changing the operating conditions were also consistent with the simulation results. The HTS electromagnet was successfully operated during the test, and there was no fault in the NI HTS coils. Finally, we confirmed the design feasibility of HTS LSM for a test vehicle.
- 28 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Design and Evaluation of Prototype High-Tc Superconducting Linear Synchronous Motor for High-Speed Transportation
We developed a prototype of a high-Tc superconducting (HTS) linear synchronous motor (LSM) and evaluated its operational performances to obtain the preliminary design data for a test vehicle having a speed of 518.4 km/h. The HTS electromagnet was fabricated using a non-insulated (NI) GdBCO HTS coil, which was designed to produce a magnetomotive force of 300 kA-turns at a cooling temperature of 20 K. A two-stage Gifford-McMahon cryocooler was used to cool the electromagnet. The prototype was tested up to 2.7 kN sufficient to the required thrust of the test vehicle. The thrust characteristics shown by changing the operating conditions were also consistent with the simulation results. The HTS electromagnet was successfully operated during the test, and there was no fault in the NI HTS coils. Finally, we confirmed the design feasibility of HTS LSM for a test vehicle.
- 1 February 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (2) , 023314
Design, construction, and operation of an 18 T 70 mm no-insulation (RE)Ba2Cu3O7−x magnet for an axion haloscope experiment
We report the design, construction, and operation results of an 18 T 70 mm cold-bore high temperature superconductor (HTS) no-insulation (NI) magnet, which is developed for an axion haloscope experiment. The magnet consists of 44 double-pancake coils wound with multi-width and multi-thickness REBa2Cu3O7−x (RE = rare earth) tapes. Owing to the NI feature, the magnet is highly compact; is 162 mm in outer diameter and 476 mm tall; and provides an environment of 0.22 T2 m3 within the cold-bore target space of 66 mm in diameter and 200 mm in length. After an initial performance test at SuNAM Co. Ltd., the magnet was installed at the Center for Axion and Precision Physics Research (CAPP) of the Institute for Basic Science in Daejeon, South Korea, in August 2017. The magnet has been successfully operating at the CAPP since then, except for maintenance in October 2018. The magnet may represent the first high field HTS user magnet that experienced long-term operation of over one year.
- 1 February 2020
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 91 (2) , 023314
Design, construction, and operation of an 18 T 70 mm no-insulation (RE)Ba2Cu3O7−x magnet for an axion haloscope experiment
We report the design, construction, and operation results of an 18 T 70 mm cold-bore high temperature superconductor (HTS) no-insulation (NI) magnet, which is developed for an axion haloscope experiment. The magnet consists of 44 double-pancake coils wound with multi-width and multi-thickness REBa2Cu3O7−x (RE = rare earth) tapes. Owing to the NI feature, the magnet is highly compact; is 162 mm in outer diameter and 476 mm tall; and provides an environment of 0.22 T2 m3 within the cold-bore target space of 66 mm in diameter and 200 mm in length. After an initial performance test at SuNAM Co. Ltd., the magnet was installed at the Center for Axion and Precision Physics Research (CAPP) of the Institute for Basic Science in Daejeon, South Korea, in August 2017. The magnet has been successfully operating at the CAPP since then, except for maintenance in October 2018. The magnet may represent the first high field HTS user magnet that experienced long-term operation of over one year.
- 9 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-5
The Post-Annealing Effect on the Pinning Properties of GdBa2Cu3O 7−δ Coated Conductors via RCE-DR
We report the post-annealing effect on the pinning properties of GdBa 2 Cu 3 O 7-δ (GdBCO) coated conductors (CCs) fabricated by a reactive co-evaporation deposition and reaction process. The GdBCO CCs annealed at 750 °C in the PO 2 of 300 mtorr for 15 min show the most enhanced critical current densities (J c ) for B//c due to the stacking faults (SF) piled up along the c-axis. The minimum J c values of post-annealed samples in relatively higher fields such as 5 T at 77 K and 7 T at 65 K were larger than those of pristine sample; although their minimum J c values were lower in relatively lower fields such as 1 T at 77 K and 3 T at 65 K. In-field J c values for B//ab were closely related to the density of SFs within samples. Analysis results by transmission electron microscopy revealed that the SF density was remarkably reduced after the post-annealing process, which is responsible for enhanced minimum J c values and significantly degraded J c values for B//ab in relatively higher fields.
- 9 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-5
The Post-Annealing Effect on the Pinning Properties of GdBa2Cu3O 7−δ Coated Conductors via RCE-DR
We report the post-annealing effect on the pinning properties of GdBa 2 Cu 3 O 7-δ (GdBCO) coated conductors (CCs) fabricated by a reactive co-evaporation deposition and reaction process. The GdBCO CCs annealed at 750 °C in the PO 2 of 300 mtorr for 15 min show the most enhanced critical current densities (J c ) for B//c due to the stacking faults (SF) piled up along the c-axis. The minimum J c values of post-annealed samples in relatively higher fields such as 5 T at 77 K and 7 T at 65 K were larger than those of pristine sample; although their minimum J c values were lower in relatively lower fields such as 1 T at 77 K and 3 T at 65 K. In-field J c values for B//ab were closely related to the density of SFs within samples. Analysis results by transmission electron microscopy revealed that the SF density was remarkably reduced after the post-annealing process, which is responsible for enhanced minimum J c values and significantly degraded J c values for B//ab in relatively higher fields.
- 30 September 2015
- Published by Korea Electric Power Corporation in KEPCO Journal on Electric Power and Energy
- Vol. 1 (1) , 151-156
Development and Characterization of High Temperature Superconducting Wire for Superconducting Cable System
- 30 September 2015
- Published by Korea Electric Power Corporation in KEPCO Journal on Electric Power and Energy
- Vol. 1 (1) , 151-156
Development and Characterization of High Temperature Superconducting Wire for Superconducting Cable System
- 1 July 2015
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 7 (7) , 1258-1264
Zirconium Doped Yttria as a Buffer Layer for GdBCO Superconductors Deposited by Chemical Solution Deposition
- 1 July 2015
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 7 (7) , 1258-1264
Zirconium Doped Yttria as a Buffer Layer for GdBCO Superconductors Deposited by Chemical Solution Deposition
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (5) , 1-5
Vision Inspection Methods for Uniformity Enhancement in Long-Length 2G HTS Wire Production
With much effort devoted by many research groups, the performance of 2nd generation (2G) superconducting wires, also called coated conductors (CC), was drastically improved, leading to many meaningful and impressive demonstrations of electric power devices. Now that the performances such as critical current, in-field characteristics, and mechanical strengths became sufficient to the application, the attention has moved to how we can produce long 2G wires with high uniformity. Many in-line inspection tools are tested and introduced to address these challenges. In this paper, we describe two methods that we adopted for in-line monitoring and feedback control of layer deposition. One is for texture control of ion beam assisted deposition (IBAD) of an MgO layer through reflection high-energy electron diffraction (RHEED) pattern monitoring and analysis. The other is for composition control of a superconducting layer through surface color observation and control of metal source evaporation rates. By applying the above two methods, we achieved in-plane texture of about 4.8 ° in the MgO layer, as measured by FWHM of phi-scan of (220) peak, and the critical current of 750 A/12 mm width in the GdBCO layer along the length of more than 650 m, with excellent uniformity.
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (5) , 1-5
Vision Inspection Methods for Uniformity Enhancement in Long-Length 2G HTS Wire Production
With much effort devoted by many research groups, the performance of 2nd generation (2G) superconducting wires, also called coated conductors (CC), was drastically improved, leading to many meaningful and impressive demonstrations of electric power devices. Now that the performances such as critical current, in-field characteristics, and mechanical strengths became sufficient to the application, the attention has moved to how we can produce long 2G wires with high uniformity. Many in-line inspection tools are tested and introduced to address these challenges. In this paper, we describe two methods that we adopted for in-line monitoring and feedback control of layer deposition. One is for texture control of ion beam assisted deposition (IBAD) of an MgO layer through reflection high-energy electron diffraction (RHEED) pattern monitoring and analysis. The other is for composition control of a superconducting layer through surface color observation and control of metal source evaporation rates. By applying the above two methods, we achieved in-plane texture of about 4.8 ° in the MgO layer, as measured by FWHM of phi-scan of (220) peak, and the critical current of 750 A/12 mm width in the GdBCO layer along the length of more than 650 m, with excellent uniformity.
- 18 March 2014
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 27 (4)
RCE-DR, a novel process for coated conductor fabrication with high performance
- 18 March 2014
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 27 (4)
RCE-DR, a novel process for coated conductor fabrication with high performance
- 10 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (3) , 1-4
Fabrication and Characterization of 4-T/203 mm RT Bore 2G HTS Magnet With No-Insulation Method
We fabricated superconducting magnet using second-generation (2G) high-temperature superconducting wire by SuNAM. Magnetic field strength at the center is 4 T, and room temperature bore diameter is 203 mm. The magnet consists of 30 double pancake coils (DPCs) with the inner diameter of 245 mm and outer diameter of 297 mm. All double pancakes were wound by no-insulation method and performance were tested separately before assemble. Tested DPCs were resistively connected by HTS tape(splice joint), and assembled coil was conduction cooled by a two-stage Gifford-McMahon cryo-cooler to the operating temperature of 8 K. The size of magnet is 452 mm in height. Current, voltage, and field strength were measured as a function of time with various ramping up and down conditions and results were compared with the simulated behavior. The coil generates 4 T when operating current ramped to 205 A by 0.03 A/s without quench. Initial cool down time was 72 h and the measure field homogeneity in 10 mm DSV was 0.015% and 0.012% in radial axis and vertical axis, respectively. The results showed that no-insulation winding method is a possible option for making compact magnet coil with sufficient structural integrity, thermal and electrical stability at the same time. The magnet showed quench at field strength of 4.49 T when ramped with 0.2 A/s to 235 A. The magnet showed same performance after recovery from quench.
- 10 January 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (3) , 1-4
Fabrication and Characterization of 4-T/203 mm RT Bore 2G HTS Magnet With No-Insulation Method
We fabricated superconducting magnet using second-generation (2G) high-temperature superconducting wire by SuNAM. Magnetic field strength at the center is 4 T, and room temperature bore diameter is 203 mm. The magnet consists of 30 double pancake coils (DPCs) with the inner diameter of 245 mm and outer diameter of 297 mm. All double pancakes were wound by no-insulation method and performance were tested separately before assemble. Tested DPCs were resistively connected by HTS tape(splice joint), and assembled coil was conduction cooled by a two-stage Gifford-McMahon cryo-cooler to the operating temperature of 8 K. The size of magnet is 452 mm in height. Current, voltage, and field strength were measured as a function of time with various ramping up and down conditions and results were compared with the simulated behavior. The coil generates 4 T when operating current ramped to 205 A by 0.03 A/s without quench. Initial cool down time was 72 h and the measure field homogeneity in 10 mm DSV was 0.015% and 0.012% in radial axis and vertical axis, respectively. The results showed that no-insulation winding method is a possible option for making compact magnet coil with sufficient structural integrity, thermal and electrical stability at the same time. The magnet showed quench at field strength of 4.49 T when ramped with 0.2 A/s to 235 A. The magnet showed same performance after recovery from quench.
- 1 November 2013
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 494, 242-245
The performance of the conduction cooled 2G HTS magnet wound without turn to turn insulation generating 4.1T in 102mm bore
- 1 November 2013
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 494, 242-245
The performance of the conduction cooled 2G HTS magnet wound without turn to turn insulation generating 4.1T in 102mm bore