Nasir Ahmad Rather
Research Subjects
Research Interests
Nasir Ahmad Rather has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Mohd Akbar Lone
Department of Civil Engineering, National Institute of Technology Srinagar, Srinigar 190006, India
6 shared publicationsAbdul Qayoom Dar
Department of Civil Engineering, National Institute of Technology Srinagar, Hazratbal 190006, Jammu and Kashmir, India
2 shared publications- Abdul Qayoom Dar
Department of Civil Engineering, National Institute of Technology, Srinagar, India
2 shared publications - Bintul Huda Mir
National Institute of Technology
2 shared publications Mir Bintul Huda
Water Resources Management Centre, National Institute of Technology Srinagar, Srinigar 190006, India
2 shared publicationsAaron Anil Chadee
Department of Civil and Environmental Engineering, University of West Indies St. Augustine, St. Augustine, Trinidad & Tobago
1 shared publication
Latest Publications
- Open Access
- 1 July 2023
- Published by IWA Publishing in Water Practice & Technology
- Vol. 18 (7) , 1608-1616
Scouring around different shapes of bridge pier
Scouring is a complex process dependent on several factors, and local scour is more complex than general scour. This study was an attempt to predict local scour round bridge piers based on general scour in the water stream. Three obstacle shapes were used – circular, round-nosed, and elliptical – as they are predominant in hydraulic structures like bridge piers. For each obstacle shape, scour depth was measured around the periphery for five gradually increasing discharges and in two types of bed material. The local scour results were analyzed to relate them to general scour. Lacey's equation was used to estimate general scour. Models were developed for the three common shapes, by which local scour for any particular shape can be predicted based on general scour in the stream.
- 1 July 2023
- Published by IWA Publishing in Water Practice & Technology
- Vol. 18 (7) , 1608-1616
Open AccessScouring around different shapes of bridge pier
Scouring is a complex process dependent on several factors, and local scour is more complex than general scour. This study was an attempt to predict local scour round bridge piers based on general scour in the water stream. Three obstacle shapes were used – circular, round-nosed, and elliptical – as they are predominant in hydraulic structures like bridge piers. For each obstacle shape, scour depth was measured around the periphery for five gradually increasing discharges and in two types of bed material. The local scour results were analyzed to relate them to general scour. Lacey's equation was used to estimate general scour. Models were developed for the three common shapes, by which local scour for any particular shape can be predicted based on general scour in the stream.
- Open Access
- 4 June 2021
- Published by IWA Publishing in Water Supply
- Vol. 21 (8) , 4121-4129
Determination of hydraulic conductivity for granular filters based on constriction size and shape parameters
This experimental study is an attempt to apply the constriction size concept for determination of hydraulic conductivity of filter material. Five shapes of granular filter material of different gradations were used for the experimental investigations. The controlling constriction size for selected shapes and gradations were worked out and related to the experimental values of hydraulic conductivity. The empirical model for determination of hydraulic conductivity based on controlling constriction size for each shape of granular filter material was developed. Finally, a combined empirical model for the determination of hydraulic conductivity of granular filters was developed based on shape parameters and the controlling constriction size. The model was validated with the experimental data of a past research work; the predicted values of hydraulic conductivity were found in close approximation to the values obtained from the literature. Results of the present work will help in improving the existing design criteria of protective filters, which form an integral part of the safety of hydraulic structures.
- 4 June 2021
- Published by IWA Publishing in Water Supply
- Vol. 21 (8) , 4121-4129
Open AccessDetermination of hydraulic conductivity for granular filters based on constriction size and shape parameters
This experimental study is an attempt to apply the constriction size concept for determination of hydraulic conductivity of filter material. Five shapes of granular filter material of different gradations were used for the experimental investigations. The controlling constriction size for selected shapes and gradations were worked out and related to the experimental values of hydraulic conductivity. The empirical model for determination of hydraulic conductivity based on controlling constriction size for each shape of granular filter material was developed. Finally, a combined empirical model for the determination of hydraulic conductivity of granular filters was developed based on shape parameters and the controlling constriction size. The model was validated with the experimental data of a past research work; the predicted values of hydraulic conductivity were found in close approximation to the values obtained from the literature. Results of the present work will help in improving the existing design criteria of protective filters, which form an integral part of the safety of hydraulic structures.
- 8 September 2020
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 44 (S1) , 491-496
Design Procedure of Elongated Shape Filters for Cohesionless Soils
- 8 September 2020
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 44 (S1) , 491-496
Design Procedure of Elongated Shape Filters for Cohesionless Soils
- 18 September 2018
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 43 (S1) , 323-330
Significance of Shape Factor of Obstacle on Local Scour
- 18 September 2018
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 43 (S1) , 323-330
Significance of Shape Factor of Obstacle on Local Scour
- 16 May 2018
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 15 (6) , 774-781
Laboratory investigations for development of design criteria for varying shapes of protective filters
Laboratory investigations have been carried out in the past regarding the design of protective filters based on the controlling constriction size of the filter mass. In all such studies, the particle shape has been considered spherical. However the fact remains, that the controlling constriction size changes with shape of filter particles. The present study is an attempt to assess the effect of shape on controlling constriction size usually based on the concept of spherical shape, and subsequently observe its effect on the design criteria adopted for filters. Based on laboratory investigations for three different shapes of filter material i.e. elliptical, sub-rounded and irregular, the improvements to the existing filter design criterion are proposed in this study by way of correction factors for each shape of filter material.
- 16 May 2018
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 15 (6) , 774-781
Laboratory investigations for development of design criteria for varying shapes of protective filters
Laboratory investigations have been carried out in the past regarding the design of protective filters based on the controlling constriction size of the filter mass. In all such studies, the particle shape has been considered spherical. However the fact remains, that the controlling constriction size changes with shape of filter particles. The present study is an attempt to assess the effect of shape on controlling constriction size usually based on the concept of spherical shape, and subsequently observe its effect on the design criteria adopted for filters. Based on laboratory investigations for three different shapes of filter material i.e. elliptical, sub-rounded and irregular, the improvements to the existing filter design criterion are proposed in this study by way of correction factors for each shape of filter material.
- 28 August 2017
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 13 (6) , 608-614
Design criteria of blade shape filter material for graded cohesion less bases
The paper presents a study on development of filter design criteria based on controlling constriction pore size of non-spherical, non-uniform filter material for graded cohesion less base. It is a deviation from the existing design criteria of protective filters which are mostly based on the certain particle size ratios of filter and base materials and consider the shape of the particles of filter material as spherical. Some studies were carried out earlier on the non-uniform filter material size, but there also the particles have been considered as spherical in shape. To ascertain the effect of shape of the non-uniform filter material on the design criteria of protective filters, the blade-shaped non-uniform filter material was used in the present study. Based on this study, it was observed that the criteria developed for non-uniform filter material particles considering the particle shape as spherical do not hold good for non-spherical shapes of the filter material. The blade-shaped filter material used in the present study was found to protect even finer bases than what was suggested by most of the existing criteria which were based on spherical shape filter material.
- 28 August 2017
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 13 (6) , 608-614
Design criteria of blade shape filter material for graded cohesion less bases
The paper presents a study on development of filter design criteria based on controlling constriction pore size of non-spherical, non-uniform filter material for graded cohesion less base. It is a deviation from the existing design criteria of protective filters which are mostly based on the certain particle size ratios of filter and base materials and consider the shape of the particles of filter material as spherical. Some studies were carried out earlier on the non-uniform filter material size, but there also the particles have been considered as spherical in shape. To ascertain the effect of shape of the non-uniform filter material on the design criteria of protective filters, the blade-shaped non-uniform filter material was used in the present study. Based on this study, it was observed that the criteria developed for non-uniform filter material particles considering the particle shape as spherical do not hold good for non-spherical shapes of the filter material. The blade-shaped filter material used in the present study was found to protect even finer bases than what was suggested by most of the existing criteria which were based on spherical shape filter material.