Brooks H. Smith
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Brooks H. Smith has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
B.W. Schafer
5 shared publicationsS.R. Arwade
5 shared publications- Stefan Szyniszewski
Durham University
5 shared publications J.F. Hajjar
4 shared publications- Benjamin William Schafer
Johns Hopkins University
2 shared publications - Aritra Chatterjee
Indian Institute of Technology Kharagpur, Kharagpur 721302, India
1 shared publication
Latest Publications
- 1 June 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (6)
System Reliability Benefits of Repetitive Framing in Cold-Formed Steel Floor Systems
Typical cold-formed steel floor systems involve many repetitive joist members laid in parallel, yet the design specifications are based upon the reliability of individual members and fail to account for the potential benefits imparted by repetitive framing. A repetitive member factor, similar to that used in the United States National Design Specifications (NDS) for wood, could be used in cold-formed steel (CFS) design to recognize these benefits and allow for more economical and efficient design that does not compromise safety. This paper introduces and validates procedures based on Monte Carlo simulation for assessing the performance of repetitive floor systems under current code assumptions, and elastic and inelastic load redistribution mechanisms, and uses these procedures to examine two floor systems of varying complexity. Load redistribution is found to provide a benefit of at least 30% to the capacity of the floor system based on a target reliability index of 2.5 and therefore justifies applying a 1.25 factor to the design of joist capacity for the systems studied.
- 1 June 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 144 (6)
System Reliability Benefits of Repetitive Framing in Cold-Formed Steel Floor Systems
Typical cold-formed steel floor systems involve many repetitive joist members laid in parallel, yet the design specifications are based upon the reliability of individual members and fail to account for the potential benefits imparted by repetitive framing. A repetitive member factor, similar to that used in the United States National Design Specifications (NDS) for wood, could be used in cold-formed steel (CFS) design to recognize these benefits and allow for more economical and efficient design that does not compromise safety. This paper introduces and validates procedures based on Monte Carlo simulation for assessing the performance of repetitive floor systems under current code assumptions, and elastic and inelastic load redistribution mechanisms, and uses these procedures to examine two floor systems of varying complexity. Load redistribution is found to provide a benefit of at least 30% to the capacity of the floor system based on a target reliability index of 2.5 and therefore justifies applying a 1.25 factor to the design of joist capacity for the systems studied.
- 1 November 2016
- Published by Elsevier in Engineering Structures
- Vol. 127, 434-446
Design component and system reliability in a low-rise cold formed steel framed commercial building
- 1 November 2016
- Published by Elsevier in Engineering Structures
- Vol. 127, 434-446
Design component and system reliability in a low-rise cold formed steel framed commercial building
- 1 February 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 54, 1083-1094
The mechanical properties and modeling of a sintered hollow sphere steel foam
- 1 February 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 54, 1083-1094
The mechanical properties and modeling of a sintered hollow sphere steel foam
- Open Access
Characterization of Steel Foams for Structural Components
Experimentally measured mechanical properties of hollow sphere steel foam are the subject of this paper. The characterization of the hollow sphere foam encompasses compressive yield stress and densification strain, compressive plastic Poisson’s ratio, and compressive unloading modulus, as well as tensile elastic modulus, tensile unloading modulus, tensile yield stress, and tensile fracture strain. Shear properties are also included. These tests provide sufficient information to allow calibration of a macroscopic, continuum constitutive model. Calibrated foam plasticity parameters are tabulated, and unique feature of foam plasticity are explained. Also, initial development of mesoscale simulations, which explicitly model voids and sintered hollow spheres, is reported. This work is part of a larger effort to help the development of steel foam as a material with relevance to civil engineering applications.
Open AccessCharacterization of Steel Foams for Structural Components
Experimentally measured mechanical properties of hollow sphere steel foam are the subject of this paper. The characterization of the hollow sphere foam encompasses compressive yield stress and densification strain, compressive plastic Poisson’s ratio, and compressive unloading modulus, as well as tensile elastic modulus, tensile unloading modulus, tensile yield stress, and tensile fracture strain. Shear properties are also included. These tests provide sufficient information to allow calibration of a macroscopic, continuum constitutive model. Calibrated foam plasticity parameters are tabulated, and unique feature of foam plasticity are explained. Also, initial development of mesoscale simulations, which explicitly model voids and sintered hollow spheres, is reported. This work is part of a larger effort to help the development of steel foam as a material with relevance to civil engineering applications.
- 1 October 2012
- Published by Elsevier in Thin-Walled Structures
- Vol. 59, 11-19
Local buckling strength of steel foam sandwich panels
- 1 October 2012
- Published by Elsevier in Thin-Walled Structures
- Vol. 59, 11-19
Local buckling strength of steel foam sandwich panels
- Top Cited Papers
- 1 April 2012
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 71, 1-10
Steel foam for structures: A review of applications, manufacturing and material properties
- 1 April 2012
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 71, 1-10
Top Cited PapersSteel foam for structures: A review of applications, manufacturing and material properties