Anastasia Chouprik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anastasia Chouprik has a total of 165 co-authors. Here are the top co-authors by number of shared publications:
- Andrei Zenkevich
Moscow Institute of Physics and Technology
10 shared publications - Andrey M. Markeev
Moscow Institute of Physics and Technology
10 shared publications Dmitrii Negrov
10 shared publications- Ilya Margolin
Moscow Institute of Physics and Technology , Dolgoprudny 141701
10 shared publications Vitalii Mikheev
Moscow Institute of Physics and Technology , Dolgoprudny 141701
10 shared publications- Elizaveta Kalika
Moscow Institute of Physics and Technology , 9 Institutskii Lane, Dolgoprudny 141700
7 shared publications
Latest Publications
- 7 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (10)
Origin of peak splitting in polydomain Hf0.5Zr0.5O2 ferroelectric capacitors
Low-voltage operation is widely used in hafnia-based ferroelectric memories to improve endurance and reduce power consumption, but it often leaves the ferroelectric film in a partially switched polydomain state with accelerated retention loss linked to splitting of switching current peaks. The underlying mechanisms, however, remain poorly understood. Here, we investigate the origin of switching current peak splitting in polycrystalline Hf0.5Zr0.5O2 (HZO) capacitors. Combining experiments and theory, we show that peak splitting arises from two factors: imprint acting on domain populations with opposite polarizations and grain-to-grain variations in switching kinetics. Measurements as a function of write voltage, delay time, and voltage sweep rate establish key constraints on the underlying mechanism: peak separation grows with aging time, exhibits a sweep-rate dependence indicative of charge emission during readout, and remains nearly independent of the fraction of switched domains. However, imprint alone cannot explain the smooth shape of the split peaks. To address this, we develop a stochastic switching model that combines Merz law kinetics, dead-layer-induced imprint, and statistical variations of switching parameters among individual HZO grains. The model reproduces the dependence of peak splitting on domain fraction, delay time, and sweep rate. Simulations show that peak separation is governed by the evolution of imprint-induced built-in fields, whereas the smooth peak shape originates from grain-to-grain variability. These results provide a physical understanding of imprint and retention loss in polydomain hafnia memories, aiding the optimization of low-voltage operation.
- 7 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (10)
Origin of peak splitting in polydomain Hf0.5Zr0.5O2 ferroelectric capacitors
Low-voltage operation is widely used in hafnia-based ferroelectric memories to improve endurance and reduce power consumption, but it often leaves the ferroelectric film in a partially switched polydomain state with accelerated retention loss linked to splitting of switching current peaks. The underlying mechanisms, however, remain poorly understood. Here, we investigate the origin of switching current peak splitting in polycrystalline Hf0.5Zr0.5O2 (HZO) capacitors. Combining experiments and theory, we show that peak splitting arises from two factors: imprint acting on domain populations with opposite polarizations and grain-to-grain variations in switching kinetics. Measurements as a function of write voltage, delay time, and voltage sweep rate establish key constraints on the underlying mechanism: peak separation grows with aging time, exhibits a sweep-rate dependence indicative of charge emission during readout, and remains nearly independent of the fraction of switched domains. However, imprint alone cannot explain the smooth shape of the split peaks. To address this, we develop a stochastic switching model that combines Merz law kinetics, dead-layer-induced imprint, and statistical variations of switching parameters among individual HZO grains. The model reproduces the dependence of peak splitting on domain fraction, delay time, and sweep rate. Simulations show that peak separation is governed by the evolution of imprint-induced built-in fields, whereas the smooth peak shape originates from grain-to-grain variability. These results provide a physical understanding of imprint and retention loss in polydomain hafnia memories, aiding the optimization of low-voltage operation.
- 17 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (7)
From volatile to nonvolatile resistive switching in a ferroelectric second-order memristor
Ferroelectric memristors are promising candidates for neuromorphic computing, yet their practical application is hindered by the trade-off between the volatile synaptic plasticity required for learning and the nonvolatile retention needed for long-term data storage. Here, we demonstrate a ferroelectric memristor based on an a-Si:H/Hf0.5Zr0.5O2/TiN MOS structure that resolves this challenge by tuning the ferroelectric layer thickness. By increasing the HZO thickness to 8 nm, the built-in electric field arising from charged interface traps is effectively suppressed, both extending state retention and improving endurance compared to 5 nm devices. The developed memristor exhibits dual-mode operation controlled by write pulse duration: with short pulses, it emulates biological synaptic plasticity including paired-pulse facilitation and depression, while longer pulses enable stable nonvolatile data storage. Furthermore, the device supports approximately 10 distinct and time-stable multibit conductance states via partial polarization switching. This functionality arises from the memristor's true second-order nature, where ferroelectric polarization provides nonvolatile multibit memory, and the temporal dynamics of electron injection and emission into interface traps govern synaptic behavior. The combination of long-term retention, multibit storage, and biologically inspired plasticity within a single cell positions this device as a promising building block for compact and efficient neuromorphic computing systems.
- 17 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (7)
From volatile to nonvolatile resistive switching in a ferroelectric second-order memristor
Ferroelectric memristors are promising candidates for neuromorphic computing, yet their practical application is hindered by the trade-off between the volatile synaptic plasticity required for learning and the nonvolatile retention needed for long-term data storage. Here, we demonstrate a ferroelectric memristor based on an a-Si:H/Hf0.5Zr0.5O2/TiN MOS structure that resolves this challenge by tuning the ferroelectric layer thickness. By increasing the HZO thickness to 8 nm, the built-in electric field arising from charged interface traps is effectively suppressed, both extending state retention and improving endurance compared to 5 nm devices. The developed memristor exhibits dual-mode operation controlled by write pulse duration: with short pulses, it emulates biological synaptic plasticity including paired-pulse facilitation and depression, while longer pulses enable stable nonvolatile data storage. Furthermore, the device supports approximately 10 distinct and time-stable multibit conductance states via partial polarization switching. This functionality arises from the memristor's true second-order nature, where ferroelectric polarization provides nonvolatile multibit memory, and the temporal dynamics of electron injection and emission into interface traps govern synaptic behavior. The combination of long-term retention, multibit storage, and biologically inspired plasticity within a single cell positions this device as a promising building block for compact and efficient neuromorphic computing systems.
- 23 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (12)
Stress-modulated ferroelectricity and dielectric response in HfO2
HfO 2 -based ferroelectrics offer exceptional silicon compatibility and scalability for next-generation nonvolatile memory, yet the fundamental role of mechanical stress in their functional properties remains unresolved. This study provides direct experimental and theoretical evidence that tensile stress intrinsically governs the ferroelectric and dielectric response of Hf0.5Zr0.5O2. Using a uniquely designed stretchable ferroelectric capacitor (W/Hf0.5Zr0.5O2/TiN) on a polyimide substrate, we perform in situ measurements under controlled uniaxial tensile strain. Concurrent first-principles calculations simulate strain in the polar orthorhombic Pca21HfO2 phase. Both approaches conclusively demonstrate that switchable polarization monotonically decreases with strain, dielectric permittivity increases, leakage current reduces. These reversible trends are attributed to strain-induced rearrangement of the crystal structure (not electronic effects). In turn, domain reorientation and phase exchange are ruled out as the primary mechanism. Discrepancies in the absolute values between the experiment and the theory arise from polycrystallinity, interfacial tetragonal layers, and grain boundaries. Our findings resolve long-standing debates on stress-mediated ferroelectricity in HfO2, establishing that intrinsic lattice deformation—not extrinsic factors—primarily dictates property changes. This work enables precise stress engineering for HfO2-based electronic devices.
- 23 March 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (12)
Stress-modulated ferroelectricity and dielectric response in HfO2
HfO 2 -based ferroelectrics offer exceptional silicon compatibility and scalability for next-generation nonvolatile memory, yet the fundamental role of mechanical stress in their functional properties remains unresolved. This study provides direct experimental and theoretical evidence that tensile stress intrinsically governs the ferroelectric and dielectric response of Hf0.5Zr0.5O2. Using a uniquely designed stretchable ferroelectric capacitor (W/Hf0.5Zr0.5O2/TiN) on a polyimide substrate, we perform in situ measurements under controlled uniaxial tensile strain. Concurrent first-principles calculations simulate strain in the polar orthorhombic Pca21HfO2 phase. Both approaches conclusively demonstrate that switchable polarization monotonically decreases with strain, dielectric permittivity increases, leakage current reduces. These reversible trends are attributed to strain-induced rearrangement of the crystal structure (not electronic effects). In turn, domain reorientation and phase exchange are ruled out as the primary mechanism. Discrepancies in the absolute values between the experiment and the theory arise from polycrystallinity, interfacial tetragonal layers, and grain boundaries. Our findings resolve long-standing debates on stress-mediated ferroelectricity in HfO2, establishing that intrinsic lattice deformation—not extrinsic factors—primarily dictates property changes. This work enables precise stress engineering for HfO2-based electronic devices.
- 5 January 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (1)
Polarization loss in low-power Hf 0.5 Zr 0.5 O 2 ferroelectric memory: A polydomain-aware predictive framework
- 5 January 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (1)
Polarization loss in low-power Hf 0.5 Zr 0.5 O 2 ferroelectric memory: A polydomain-aware predictive framework
- 22 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (12)
Thickness-dependent retention–endurance trade-off in scaled Hf0.5Zr0.5O2 ferroelectric capacitor
Hafnium zirconium oxide (Hf0.5Zr0.5O2) has emerged as a leading candidate for next-generation ferroelectric memory due to its superior scalability. However, the fundamental trade-offs between thickness scaling, endurance, and retention remain unresolved. Here, we systematically investigate W/Hf0.5Zr0.5O2/TiN capacitors with ferroelectric layer thicknesses from 5 to 10 nm, revealing a critical thickness-dependent performance crossover. While 6 and 8 nm films achieve optimal ferroelectric properties (2Pr up to 41 μC/cm2) and good endurance, they suffer from accelerated retention loss, suggesting that prominent (002) texture may enhance charge injection and time-dependent imprint. In contrast, a 5 nm film demonstrates a superior endurance–retention compromise. We attribute this to its significantly lower remanent polarization, which likely stems from a distinct nanocrystalline/amorphous microstructure, suppressing imprint development. Through quantitative imprint analysis, we establish that wake-up cycling simultaneously improves polarization while degrading retention—a fundamental constraint arising from the coupling between spontaneous polarization and charge injection dynamics. These findings reveal thickness-dependent design rules for achieving reliable scaled ferroelectric memories.
- 22 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (12)
Thickness-dependent retention–endurance trade-off in scaled Hf0.5Zr0.5O2 ferroelectric capacitor
Hafnium zirconium oxide (Hf0.5Zr0.5O2) has emerged as a leading candidate for next-generation ferroelectric memory due to its superior scalability. However, the fundamental trade-offs between thickness scaling, endurance, and retention remain unresolved. Here, we systematically investigate W/Hf0.5Zr0.5O2/TiN capacitors with ferroelectric layer thicknesses from 5 to 10 nm, revealing a critical thickness-dependent performance crossover. While 6 and 8 nm films achieve optimal ferroelectric properties (2Pr up to 41 μC/cm2) and good endurance, they suffer from accelerated retention loss, suggesting that prominent (002) texture may enhance charge injection and time-dependent imprint. In contrast, a 5 nm film demonstrates a superior endurance–retention compromise. We attribute this to its significantly lower remanent polarization, which likely stems from a distinct nanocrystalline/amorphous microstructure, suppressing imprint development. Through quantitative imprint analysis, we establish that wake-up cycling simultaneously improves polarization while degrading retention—a fundamental constraint arising from the coupling between spontaneous polarization and charge injection dynamics. These findings reveal thickness-dependent design rules for achieving reliable scaled ferroelectric memories.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (12)
Biorealistic response in a technology-compatible graphene synaptic transistor
Artificial synapse is a key element of future brain-inspired neuromorphic computing systems implemented in hardware. This work presents a graphene synaptic transistor based on all-technology-compatible materials that exhibits highly tunable biorealistic behavior. It is shown that the device geometry and interface properties can be designed to maximize the memory window and minimize power consumption. The device exhibits a virtually continuous range of multiple conductance levels, similar to synaptic weighting, which is achieved by gradual injection/emission of electrons into the floating gate and interface traps under the influence of an external electric field. Similar to the biological synapse, the transistor has short-term intrinsic dynamics that affects the long-term state. The temporal injection/emission dynamics of an electronic synapse closely resembles those of its biological counterpart and is exploited to emulate biorealistic behavior using a number of synaptic functions, including paired-pulse facilitation/depression, spike-rate-dependent plasticity, and others. Such a synaptic transistor can serve as a building block in hardware artificial networks for advanced information processing and storage.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (12)
Biorealistic response in a technology-compatible graphene synaptic transistor
Artificial synapse is a key element of future brain-inspired neuromorphic computing systems implemented in hardware. This work presents a graphene synaptic transistor based on all-technology-compatible materials that exhibits highly tunable biorealistic behavior. It is shown that the device geometry and interface properties can be designed to maximize the memory window and minimize power consumption. The device exhibits a virtually continuous range of multiple conductance levels, similar to synaptic weighting, which is achieved by gradual injection/emission of electrons into the floating gate and interface traps under the influence of an external electric field. Similar to the biological synapse, the transistor has short-term intrinsic dynamics that affects the long-term state. The temporal injection/emission dynamics of an electronic synapse closely resembles those of its biological counterpart and is exploited to emulate biorealistic behavior using a number of synaptic functions, including paired-pulse facilitation/depression, spike-rate-dependent plasticity, and others. Such a synaptic transistor can serve as a building block in hardware artificial networks for advanced information processing and storage.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1104-1111
Role of Ferroelectric Layer Thickness in Resistive Switching and Depolarization Effects in Hf₀.₅Zr₀.₅O₂-Based Structures
The development of low-power and high-density ferroelectric memories requires scaling the thickness of the functional layer. However, the thickness could have a significant impact on the performance of memory devices. This work examines the effect of ferroelectric layer thickness on resistive switching and depolarization phenomena in a metal-Hf0.5Zr0.5O2-Si (MFS) structure, which is the functional structure of both ferroelectric field-effect transistors (FeFETs) and ferroelectric tunnel junctions (FTJs). The MFS structures show one stable and another unstable polarization state, with the instability caused by the strong electric field produced by charged donor surface states at the Si interface and poor screening of this polarization. The rate of the unstable state depolarization slows down with increasing thickness from 5 to 10 nm, which is due to the decrease in the depolarization field at the same potential difference in the structure. The resistive effect increases with increasing thickness up to ROFF/RON = 24, which is related to the reduction of undesired conductivity along the grain boundaries of the polycrystalline Hf0.5Zr0.5O2 film. The temporal dynamics of the depolarization of the unstable polarization state and the resulting gradual switching off of the low-resistance state are close to the characteristic times of the weight change of biological synapses, and therefore, such ferroelectric memristors are suitable for emulating their behavior. The results may be useful for the development of building blocks for neuromorphic computing as well as a new generation of FeFET and FTJ-based memories.
- 24 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1104-1111
Role of Ferroelectric Layer Thickness in Resistive Switching and Depolarization Effects in Hf₀.₅Zr₀.₅O₂-Based Structures
The development of low-power and high-density ferroelectric memories requires scaling the thickness of the functional layer. However, the thickness could have a significant impact on the performance of memory devices. This work examines the effect of ferroelectric layer thickness on resistive switching and depolarization phenomena in a metal-Hf0.5Zr0.5O2-Si (MFS) structure, which is the functional structure of both ferroelectric field-effect transistors (FeFETs) and ferroelectric tunnel junctions (FTJs). The MFS structures show one stable and another unstable polarization state, with the instability caused by the strong electric field produced by charged donor surface states at the Si interface and poor screening of this polarization. The rate of the unstable state depolarization slows down with increasing thickness from 5 to 10 nm, which is due to the decrease in the depolarization field at the same potential difference in the structure. The resistive effect increases with increasing thickness up to ROFF/RON = 24, which is related to the reduction of undesired conductivity along the grain boundaries of the polycrystalline Hf0.5Zr0.5O2 film. The temporal dynamics of the depolarization of the unstable polarization state and the resulting gradual switching off of the low-resistance state are close to the characteristic times of the weight change of biological synapses, and therefore, such ferroelectric memristors are suitable for emulating their behavior. The results may be useful for the development of building blocks for neuromorphic computing as well as a new generation of FeFET and FTJ-based memories.
- 23 December 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (6)
Evolution of coercive voltage in a ferroelectric memory cell based on during its lifetime- 23 December 2024
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 22 (6)
Evolution of coercive voltage in a ferroelectric memory cell based on during its lifetime- 24 November 2024
- Published by Elsevier in Acta Materialia
- Vol. 284
Structural changes during wake-up and polarization switching in a ferroelectric Hf0.5Zr0.5O2 film
- 24 November 2024
- Published by Elsevier in Acta Materialia
- Vol. 284
Structural changes during wake-up and polarization switching in a ferroelectric Hf0.5Zr0.5O2 film