Woonsang Baek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Woonsang Baek has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Duck Young Kim
Pohang University of Science and Technology
5 shared publications - Sujeong Baek
Department of Industrial and Management Engineering, Hanbat National University, Daejeon, Republic of Korea
1 shared publication
Latest Publications
- 22 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-11
In-Process Noise Inspection System for Product Fault Detection in a Loud Shop-Floor Environment
Abnormal noise originating from within faulty products often irritates customers, which may lead to expensive warranty claims. Therefore, it is important to identify these faulty products proactively in the manufacturing process. However, noise detection in a loud shop-floor is not straightforward because inspection in an anechoic chamber is very costly, and some prerequisites for conventional noise reduction and source separation methods, such as stationary and independent signals and prior knowledge about the signal of interest, are sometimes not feasible in practice. Therefore, we developed an in-process noise inspection system that supports dual-channel acoustic data collection during the inspection process. By using two different groups of acoustic signals, abnormal sound separation and noise detection are made possible through three main steps: in-process background noise training, abnormal noise separation, and significance evaluation. The efficiency of the proposed procedure is demonstrated with two case studies: car door trim panels and dual-channel sound generator and collector.
- 22 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-11
In-Process Noise Inspection System for Product Fault Detection in a Loud Shop-Floor Environment
Abnormal noise originating from within faulty products often irritates customers, which may lead to expensive warranty claims. Therefore, it is important to identify these faulty products proactively in the manufacturing process. However, noise detection in a loud shop-floor is not straightforward because inspection in an anechoic chamber is very costly, and some prerequisites for conventional noise reduction and source separation methods, such as stationary and independent signals and prior knowledge about the signal of interest, are sometimes not feasible in practice. Therefore, we developed an in-process noise inspection system that supports dual-channel acoustic data collection during the inspection process. By using two different groups of acoustic signals, abnormal sound separation and noise detection are made possible through three main steps: in-process background noise training, abnormal noise separation, and significance evaluation. The efficiency of the proposed procedure is demonstrated with two case studies: car door trim panels and dual-channel sound generator and collector.
- Open Access
An in-Process Inspection System to Detect Noise Originating from within the Interior Trim Panels of Car Doors
Car body parts are sometimes responsible for irritating noise caused by assembly defects. Typically, various types of noise are known to originate from within the interior trim panels of car doors. This noise is considered to be an important factor that degrades the emotional satisfaction of the driver of the car. This research suggests an in-process inspection system consisting of an inspection workstation and a noise detection method. The inspection workstation presses down the car door trim panel by using a pneumatic pusher while microphones record the acoustic signals directly above the door trim panel and on the four sides of the workstation. The collected signals are analyzed by the proposed noise detection method after applying noise reduction. The noise detection method determines the presence of irritating noise by using noise source localization in combination with the time difference of arrival method and the relative signal strengths. The performance of the in-process noise detection system was evaluated by conducting experiments on faulty and healthy car door trim panels.
Open AccessAn in-Process Inspection System to Detect Noise Originating from within the Interior Trim Panels of Car Doors
Car body parts are sometimes responsible for irritating noise caused by assembly defects. Typically, various types of noise are known to originate from within the interior trim panels of car doors. This noise is considered to be an important factor that degrades the emotional satisfaction of the driver of the car. This research suggests an in-process inspection system consisting of an inspection workstation and a noise detection method. The inspection workstation presses down the car door trim panel by using a pneumatic pusher while microphones record the acoustic signals directly above the door trim panel and on the four sides of the workstation. The collected signals are analyzed by the proposed noise detection method after applying noise reduction. The noise detection method determines the presence of irritating noise by using noise source localization in combination with the time difference of arrival method and the relative signal strengths. The performance of the in-process noise detection system was evaluated by conducting experiments on faulty and healthy car door trim panels.
- 24 August 2019
- Published by Springer Nature
- p. 413-420
In-Process Noise Detection System for Product Inspection by Using Acoustic Data
- 24 August 2019
- Published by Springer Nature
- p. 413-420
In-Process Noise Detection System for Product Inspection by Using Acoustic Data
- 25 August 2018
- Published by Springer Nature
- p. 35-38
An In-Process BSR-Noise Detection System for Car Door Trims
- 25 August 2018
- Published by Springer Nature
- p. 35-38
An In-Process BSR-Noise Detection System for Car Door Trims
- Open Access
Characterization of System Status Signals for Multivariate Time Series Discretization Based on Frequency and Amplitude Variation
Many fault detection methods have been proposed for monitoring the health of various industrial systems. Characterizing the monitored signals is a prerequisite for selecting an appropriate detection method. However, fault detection methods tend to be decided with user’s subjective knowledge or their familiarity with the method, rather than following a predefined selection rule. This study investigates the performance sensitivity of two detection methods, with respect to status signal characteristics of given systems: abrupt variance, characteristic indicator, discernable frequency, and discernable index. Relation between key characteristics indicators from four different real-world systems and the performance of two fault detection methods using pattern recognition are evaluated.
Open AccessCharacterization of System Status Signals for Multivariate Time Series Discretization Based on Frequency and Amplitude Variation
Many fault detection methods have been proposed for monitoring the health of various industrial systems. Characterizing the monitored signals is a prerequisite for selecting an appropriate detection method. However, fault detection methods tend to be decided with user’s subjective knowledge or their familiarity with the method, rather than following a predefined selection rule. This study investigates the performance sensitivity of two detection methods, with respect to status signal characteristics of given systems: abrupt variance, characteristic indicator, discernable frequency, and discernable index. Relation between key characteristics indicators from four different real-world systems and the performance of two fault detection methods using pattern recognition are evaluated.